CONTENTS INTRODUCTION SAFETY STICKERS INSTALLATION INSTRUCTIONS 2 3 4 Inspection for damage Location of Bakery Case Leveling of Bakery Case PACKAGING MATERIAL LIGHTS SHELVES ELECTRICAL INFORMATION WIRING DIAGRAM OPERATING INSTRUCTIONS 5 5 5 6 7 8 Controls Anti Moisture Fans How to place product Shelf placement Replacement of light 9 9 10 11 FRONT CURVED GLASS MAINTENANCE & CLEANING Cleaning daily Cleaning weekly Condenser Coil 12 13 TROBLE SHOOTING Bakery Case not working Bakery Case warm Glass swe
INTRODUCTION This owner’s manual has important information. Please read the entire manual before installing your new Turbo Air Refrigerated Bakery Case. After reading manual if you have any questions, please fill free to call: CUSTOMER SERVICE DEPARTMENT TURBO AIR 1250 VICTORIA ST. CARSON, CA 90746 1-800-381-7770 1-800-627-0032 Please write down model and serial number for making any reference to this unit.
SAFETY STICKERS The following signs are thru out Turbo Air Bakery Case. If any are missing, Pleae call Customer Service so the sticker can be sent to you. DANGER HIGH VOLTAGE-This sticker is on back of bakery case. CAUTION-This sticker is below the Bakery display pan. ! CAUTION-This sticker is on back of bakery case. Please follow all safety warnings on stickers. Make sure all employees understand warnings. Have all employees read manual for your and their safety.
INSTALLATION INSTRUCTIONS INSPECTION FOR DAMAGE Customer is responsible for checking for damage. First inspect crate as soon sa it arrives. Prior to signing if crate is damaged make sure you note that on bill of lading. If after uncrating there is concealed damaged and crate was in good condition you must call Customer Service at Turbo Air. Concealed damage must be reported within 24 hours of receiving unit. Bill of lading will be requested faxed to claim department.
PACKAGING MATERIAL Remove all tape that holds lift up glass and doors in place. Some residue will be left and this can be removed with glass cleaner. Remove all plastic ties that hold shelves and brackets for shelves. LIGHTS Make sure lights are in their lamp holders. Also make sure plugs for lamp holders are completely plugged in. If they are loose it may cause lamp holder to burn. SHELVES To install shelves in desired position front glass must be open and rear doors removed.
ELECTRICAL INFORMATION !!! BAKERY CASE MUST BE GROUNDED Only a licensed electrician must install all electrical on Bakery Case. All electrical must be done in accordance with applicable electrical standards. A dedicated breaker is to be used for each Bakery Case. Electrical must be grounded upon installation An access hole is provided thru base of case for running electrical up through floor. Also a hole is provided in the back of unit to run electrical. Unit is designed to be hardwired by electrician.
WIRING DIAGRAM(TCB-5R)
OPERATING INSTRUCTIONS After installing unit and all electrical to Bakery Case, unit is ready to start up. CONTROLS POWER SWITCH:It is labeled with on/off position. It controls power to the entire Bakery Case. LIGHT SWITCH:The switch controls the power to the lighting circuit. The switch rocker is red in the “on” position, black in the “off” position. TEMPERATURE CONTROL: TCB-5R 1. The controller(thermostat) is locatef at the right inside of the unit. 2. The factory setting for the control is Normal 3.
SHELF PLACEMENT: The shelves can be installed slanted or straight. To make the shelf slanted do the following; a. Shelf needs to be removed from shelf support. b. Shelf support needs to be held at each end. c. Shelf support needs to be lifted at the back till bracket can inserted into shelf standard slots. Refer to drawing of pages 5. ADJUSTING SHELF LEVEL Shelves can be sdjusted up or down. To move shelves do the following; a. Lights must be turned off. b. Grasp plug for light cord and unplug. c.
FRONT CURVED GLASS !!!WARNING The Bakery Case is not intended for self serve. Do not let customers lift front glass. Only trained personnel should lift curved glass. Under normal use hinges will last many years. If any of the following problems occur, plase call Customer Service; a. Front curved glass closes rapidly. b. Front curves glass does not open easily. c. Front curved glass does not stay open, when in the opened position.
MAINTENANCE & CLEANING !!! Always before cleaning Bakery Case unit should be turned off at power switch and lights should be turmed off. Removed product and allow display to reach room temperature. !!! Do not wet electrical components. BAKERY CASE SHOULD BE CLEANED THOROUGHLY BEFORE FIRST USE. CLEANING DAILY a. Do not clean with detergents. Use a mild soap. b. If door track is dirty remove doors. Keeping door track clean allows for doors to slide easily. Food silicone can be sprayed on rollers and track.
MAINTENANCE CONTINUED CONDENSER COIL a. Turn off unit at power switch. Disconnect power to unit. b. Remove rear grill. c. Clean condenser by either brushing off with stiff wire brush or vacuuming with wet/dry vacuum. Condenser is black and looks like a radiator. This should be cleaned every month or as necessary. Keeping clean allows for maximum cooling of unit and long life of compressor.
TROUBLE SHOOTING For any problems with BAKERY-Case please refer to following check list. If still having a problem or need to ask a question please call Customer Service at 1-800-381-7770 or 1-800-627-0032 BAKERY CASE NOT WORKING a. Check to see if breaker is not tripped. b. Check power gowing to unit. c. Check thermostat is set at on position. d. Check power switch is on. BAKERY CASE WARM a. Check condenser to see if clean. b. Check that doors and curved glass are closed tightly. c.
WARRANTY STATEMENT WARRANTY CLAIMS All claims for parts or labor must be made directly through Turbo Air. All claims should include : model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all pertinent information supporting the alleged defect. In case of compressor replacement under warranty, either compressor or compressor tag must be returned to Turbo Air along with above listed information.
WHAT IS NOT COVERED BY THIS WARRANTY Turbo Air's sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty neither assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty. NO CONSEQUENTIAL DAMAGES.