GLASS DOOR ICE MERCHANDISERS Please read this manual completely before attempting to install or operate this equipment! An asterisk(*) in a model number means the external finish of cabinet, black & white color, and each model is identical except the aesthetic difference which doesn't affect the performance. Model No.
CONTENTS PAGE 1. SPECIFICATIONS ........................................................................................ 2 2. SERIAL NUMBER ........................................................................................ 2 3. NOTICE TO CUSTOMER / INSTALLATION ............................................... 3 4. CLEANING ................................................................................................... 4 5. BASIC OPERATION ............................................................
NOTICE TO CUSTOMER Loss or spoilage of products in your refrigerator/freezer is not covered by warranty. In addition to following recommended installation procedures, you must run the refrigerator/ freezer 24 hours prior to usage. INSTALLATION 1. GOOD AIR CIRCULATION - Please make sure to avoid any partition and object which may stop the air flow. - Please make sure there is enough space for air circulation to the rear of the unit.
CLEANING 1. CLEANING STAINLESS STEEL INTERIOR AND EXTERIOR : Damage to stainless steel finish due to improper use of cleaning products or non- recommended products is NOT covered under this product's warranty. • Do - Use warm, soapy water and a soft, clean cloth or sponge. - Rinse surfaces with clean, warm water and dry immediately to avoid water spots.
BASIC OPERATION 1. Plug in and turn on the power and lamp switch located on the top of the bottom grille right side. The display panel will light up and make a beeping noise.The compressor will begin to run. 2. The default temperature setting is No. “16˚F” for the TGIM-23*. The default temperature setting is No. “16˚F” for the TGIM-49*. 3. The compressor is automatically cycled by the electronic controller (PCB, F-Sensor). 4. The defrost cycle is automatically controlled by the D-sensor, and the PCB. 5.
DISPLAY PANEL OF FREEZER (TGIM-23*) TEMP CONTROL BUTTON (SEE PAGE 8) LAMP SWITCH INTERIOR TEMP INDICATOR (SEE PAGE 9) POWER SWITCH TEMPERATURE Turbo air LAMP T.F.
DISPLAY PANEL OF FREEZER (TGIM-49*) TEMP CONTROL BUTTON (SEE PAGE 8) LAMP SWITCH INTERIOR TEMP INDICATOR (SEE PAGE 9) POWER SWITCH LAMP POWER TEMPERATURE T.F.
TURBO FREEZE 1. If you push the T.F. (Turbo Freeze) button, the compressor will run for 120 minutes to bring down the temperature more quickly. 2. If you push the T.F. button again during Turbo Freeze mode, the compressor will return to the normal operation. 3. During the Turbo Freeze mode, the temperature Up(+)/Down(-) button will not affect the compressor’s operation. UP(+)/DOWN(-) BUTTON (Temperature control button) 1.
INNER TEMPERATURE DISPLAY 1. It displays inside temperature. 2. Display range is -40˚F to 99˚F (-40˚C ~ +40˚C). 3. When inside temperature is lower than -40˚F, the panel will display ‘ and, higher than +99˚F, the panel will show ‘ ’. ’. FAN RUNNING INDICATOR 1. If the fan motor is running, fan running indicator will be turned on. 2. Evaporator fan motor will stop when the door is opened. DOOR OPENING INDICATOR 1. If the door is opened, an indicator will be turned on. 2.
BEFORE REQUESTING SERVICE SYMPTOMS CAUSES SOLUTIONS The unit is freezing or • The temperature is set too high • Push the temperature button to the suitable position. or low to contain food fresh. melting food. The unit does not refrigerate at all. • There is a power connection failure problem. • Check the power cord and plug in it correctly. The unit does not refrigerate well. • The unit is in sunlight or near a heating device. • The unit contains hot food or too much food.
Warranty Claims... All claims for parts or labor must be made directly thorough Turbo Air. All claims should include: model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all pertinent information supporting the alleged defect. In case of compressor replacement under warranty, either compressor or compressor tag must be returned to Turbo Air along with above listed information. Failure to comply with warranty policies will result in voiding claims.
WARRANTY REGISTRATION CARD TURBO AIR MANUFACTURING COMPANY 4184 Conant St Long Beach, CA 90808, U.S.A. (Name of your business) MANUFACTURING COMPANY MAIL CARD IMMEDIATELY (Address) (Model No. of Unit) (City and State of Purchaser) (Unit Serial Number) (Compressor Serial Number) This is to inform TURBO AIR MANUFACTURING COMMPANY that I, This card must be mailed immediately after installation date for warranty to be in effect.
4184 CONANT ST LONG BEACH, CA 90808 U.S.A & Canada Toll Free 800-627-0032 For Service 800-381-7770 TEL: 310-900-1000 FAX: 310-900-1077 http://www.turboairinc.