Headquarter: 1250 Victoria street CARSON, CA 90746 & Canada Toll Free 800-627-0032 TEL: 310-900-1000 FAX: 310-900-1077 www.turboairinc.
Commercial Refrigerator & Freezer Service Manual Model No.
Commercial Refrigerator Service Manual Model No.
TABLE OF CONTENTS 1. FEATURE CHART ............................................................................................................ 2 2. WIRING DIAGRAM ......................................................................................................... 12 3. REFRIGERANT CYCLE DIAGRAM ............................................................................. 17 4. SPECIFICATION OF MAIN COMPONENTS ............................................................... 18 5.
1.
FEATURE CHART • Model : TGM-48R, 45R, 35R, 33R SIGN PANEL DOOR DOOR HANDLE BOTTOM GRILL LEVELING LEG < FRONT > EVAPORATOR COIL • Model : TGM-48R, 35R FLUORESCENT LAMP EVAPORATOR FAN MOTOR EVAORATOR FAN BLADE THERMOSTAT FLOURESCENT LAMP SHELF CONDENSER FAN BLADE CONDENSER FAN MOTOR DRAIN PAN COMPRESSOR CONDENSER COIL < SIDE > 3
FEATURE CHART • Model : TGM-45R, 33R EVAPORATOR COIL COMPRESSOR CONDENSER COIL DRAIN PAN < SIDE > 4
FEATURE CHART • Model : TGM-22R SIGN PANEL SHELF BOTTOM GRILL DOOR GLASS LEVELING LEG < FRONT > • Model : TGM-22R EVAPORATOR EVAPORATOR THERMOSTAT FAN MOTOR FAN BLADE EVAPORATOR COIL BALLAST SIGN PANEL FLUORES -CENT LAMP DRAIN ELBOW DOOR HINGE TOP DRAIN HOSE SUCTION PIPE -COVER HANDLE DOOR HINGE BOTTOM COMPRESSOR CONDENSER COIL DRAIN PAN CONDENSER FAN BLADE CONDENSER FAN MOTOR < SIDE > 5
FEATURE CHART • Model : TGM-22RV < FRONT > • Model : TGM-22RV < SIDE > 6
FEATURE CHART • Model : TGM-14R SIGN PANEL SHELF BOTTOM GRILL DOOR GLASS LEVELING LEG < FRONT > • Model : TGM-14R EVAPORATOR COIL EVAPORATOR FAN MOTOR BALLAST SIGN PANEL FLUORES -CENT LAMP DOOR HANDLE DRAIN PAN CONDENSER COIL CONDENSER FAN MOTOR COMPRESSOR < SIDE > 7
FEATURE CHART • Model : TGM-14RV < FRONT > • Model : TGM-14RV < SIDE > 8
FEATURE CHART • Model : TGM-11RV < FRONT > • Model : TGM-11RV < SIDE > 9
FEATURE CHART • Model : TGM-11R FLUORESCENT LAMP SIGN PANEL STICKER SHELF BOTTOM GRILL LEVELING LEG < FRONT > EVAPORAOR FAN MOTOR • Model : TGM-11R EVAPORATOR FAN BLADE EVAPORATOR COIL CONDENSER FAN MOTOR CONDENSER FAN BLADE COMPRESSOR CONDENSER COIL DRAIN PAN < SIDE > 10
FEATURE CHART • Model : TGM-5R THERMOSTAT CONTROL BOX FLUORE SCENT LAMP EVAPORATOR SHELF DRAIN PAN GASKET LAMP SWITCH DOOR < FRONT > • Model : TGM-5R DOOR HANDLE CONDENSER LEVELING LEG < SIDE > 11
• Model : TGM-48R 12 WH WH WH WH YW YW YW YW WH WH S/C WH WH WH YW YW LAMP SWITCH RD BL RD BL WH CO MP BK GY GY CONDENSING MOTOR COOLING MOTOR (2) BK BALLAST F/L LAMP F/L LAMP YW YW BK E POWER THERMOSTAT BK BK BK BK WH WH WH WH BL BK RD BK BL RD COOLING MOTOR (1) F/L LAMP F/L LAMP BALLAST LAMP SWITCH 2.
WIRING DIAGRAM • Model : TGM-45R 3 4 • Model : TGM-35R 13
WIRING DIAGRAM • Model : TGM-33R 3 • Model : TGM-5R 14 F/L Lamp(17W) F/L Lamp(17W) 4
WIRING DIAGRAM • Model : TGM-22R • Model : TGM-14R BK THERMOSTAT • Model : TGM-11R BK BK 3 4 BK WH GY WH M A3 OL G/S F/M1 FL (13W) F/M2 WH 1 GN COMPRESSOR & P-RELAY POWER PLUG WH 15 WH BL BL BR BALLAST(13W) S/V WH R/C PK BK 2 WH WH WH
WIRING DIAGRAM • Model : TGM-22RV • Model : TGM-14RV • Model : TGM-11RV 16
3.
4. SPECIFICATION OF MAIN COMPONENTS 1. COMPRESSOR HORSE POWER CAPACITY AKA4482YXA 30200K2900 3/4 HP 8,200 BTU/h CSIR 1,190W TECUMSEH AKA4476YXA 30200A4700 1/2 HP 7,880 BTU/h (856 Kcal/h) CSIR 750W TECUMSEH AEA4448YXA 30200J2100 1/3 HP 4,650 BTU/h CSIR 457W TECUMSEH MODEL PART NAME TGM69R PART NO.
SPECIFICATION OF MAIN COMPONENTS 4. CONDENSER FAN MOTOR BLADE (NUMBER) MODEL PART NAME PART NO. POLE INPUT TYPE MAKER TGM69R TGM48R TGM45R TGM35R TGM33R IS-4420DWSG-1 3963220410 4P 47W Shaded Pole Induction Aluminum SUNGSHIN (5) TGM22R / TGM22RV IS-4420DWSR-1 3963229000 4P 47W TGM14R / TGM14RV IS-3225DWSQ-2 TGM11R / TGM-11RV 3963326710 2P 36W Shaded Pole Induction Shaded Pole Induction Aluminum SUNGSHIN (5) Zytel SUNGSHIN (6) 5.
SPECIFICATION OF MAIN COMPONENTS 7.
5. TROUBLE SHOOTING CHART 1.
TROUBLE SHOOTING CHART 2.
TROUBLE SHOOTING CHART 3.
TROUBLE SHOOTING CHART 4.
6. PARTS DIAGRAM 1.
PARTS DIAGRAM 2.
PARTS DIAGRAM •Model : TGM-22R, 22RV 27
PARTS DIAGRAM •Model : TGM-14R, 14RV, 11R, 11RV 28
PARTS DIAGRAM •Model : TGM-5R 29
PARTS DIAGRAM 3.
PARTS DIAGRAM •Model : TGM-48R, 45R, 35R, 33R Door Channel Top Door Stopper Cushion Door Seal Top Door Gasket Door Frame Door Glass Door Handle Door Seal Bottom Door Chabbel Right Door Roller(A) Door Assembly*LEFT Door Channel Left Door Roller(C) Door Rail Door Channel Bottom 31 Door Assembly*RIGHT
PARTS DIAGRAM •Model : TGM-22R, 22RV, 14R, 14RV, 11R, 11RV 32
PARTS DIAGRAM •Model : TGM-5R 33
PARTS DIAGRAM 4.
PARTS DIAGRAM •Model : TGM-69R, 45R, 33R 35
PARTS DIAGRAM •Model : TGM-22R, 22RV 36
PARTS DIAGRAM •Model : TGM-14R, 14RV 37
PARTS DIAGRAM •Model : TGM-11R.
PARTS DIAGRAM •Model : TGM-5R 39
PARTS DIAGRAM 5.
PARTS DIAGRAM •Model : TGM-69R, 45R, 33R Lamp Switch Ballast Lamp Socket Lamp (for Sign Panel) Lamp Socket Lamp (for Cabinet Liner) Lampshield 41 Lampshield End Cap
PARTS DIAGRAM •Model : TGM-14R 42
PARTS DIAGRAM •Model : TGM-22RV, 14RV, 11RV •Model : TGM-22RV, 14RV, 11RV •Model : TGM-22RV, 14RV 43
PARTS DIAGRAM •Model : TGM-11R, 5R 44
PARTS DIAGRAM 6.
PARTS DIAGRAM 7.
PARTS DIAGRAM •Model : TGM-45R, 33R, 22R, 22RV, 14R, 14RV 47
PARTS DIAGRAM 8.
PARTS DIAGRAM 9.
7.
PARTS LIST Part Name Part Number Description Model 69 48 45 35 33 22 14 11 5 1 1 1 1 Dryer 30268A0100 30g Refer Parts Diagram Dryer 30268H0100 30g Refer Parts Diagram Dryer 30268F0403 30g Refer Parts Diagram Dryer 30268K0100 30g Refer Parts Diagram Dryer 3016801300 10g Refer Parts Diagram Dryer 30268Q0300 C-052-S 1 1 Power Cord 30213A1000 KKP-30B 1 1 1 1 1 1 1 1 1 Power Cord Clamp 30212A0600 SPG 1 1 1 1 1 1 1 1 1 Drain Wicking Pad 30245A0700 1 1 1 1 1 1 1 1 1 1 1 Drain Pan
PARTS LIST Door Glass 30255K0100 T24 Model 69 48 45 35 33 22 14 11 5 1 Door Glass 30255J1100 T24 1 Door Glass 30255J0200 T24 Door Glass 30255D0110 T24 Door Glass 30255A0110 T24 Door Glass 30255H1100 T24 Door Glass 30255F1100 T24 Door Glass 30255A9010 T24 Door Glass 30255G1100 T24 Part Name Part Number Description 1 1 1 1 1 1 1 Door Handle 30226A0101 Slide ABS Plastic Black Door Handle 30226G0101 Swing Aluminum Door Handle 3022600300 Swing Aluminum Door Hinge Bracke
PARTS LIST Door Channel Left 30287K0500 PVC-H, Left Model 69 48 45 35 33 22 14 11 5 1 Door Channel Right 30287K0600 PVC-H, Right 1 Door Rail 30287D0300 Stainless Door Rail 30287A0500 Stainless Door Rail 30287J2200 Stainless Door Rail 30287J2100 Stainless Door Rail (A) 30287K0100 SUS304 1 Door Rail (B) 30287K0200 SUS304 1 Door Roller 30247A0500 Part Name Part Number Description 1 1 1 1 1 Door Roller 30206A1400 Door Roller 30206D0300 Door Roller 30247K0200 Tok DU-22-H
PARTS LIST Part Name Part Number Description Model 69 48 45 35 33 22 14 11 5 2 Evaporator Fan Motor 3963328610 IS-3210DWSB-2 Evaporator Fan Motor 3963328110 IS-4420DWSN-2 Evaporator Fan Motor 3963328120 IS-4420DWSN-2A Evaporator Fan Motor 3963328620 IS-3210DWSB-3 Evaporator Fan Motor Blade 30218F0100 Zytel ф 150 Evaporator Fan Motor Blade 4034L38038 Zytel ф 158 Evaporator Fan Motor Blade 3011800400 ABS ф 110 Evaporator Fan Motor Blade 30218F0200 AL ф 175 Evaporator Fixture 30220
PARTS LIST Part Number Description Bottom Grill Assembly 30224F0102 Front ABS Dark Gray Model 69 48 45 35 33 22 14 11 5 1 1 Bottom Grill Assembly 30224K0100 Ass’y Grill 1 Ballast 30285D0500 32Watt x 1 R-2P32-TP 2 1 Ballast 30285A0700 32Watt x 1 R-1P32-TP 1 1 1 Ballast 30200A0110 25Watt x 1 R-1P825-TP 1 Ballast 30285J1200 25Watt x 2 R-2P825-TP Ballast 30285H1500 17Watt x 2 R-2P817-TP Part Name Lightings Ballast 30200A0140 13Watt x 1 DD22B Lamp 30200D2800 32Watt F32T8/TL8504
PARTS LIST Part Name Part Number Description Model 69 48 45 35 33 22 14 11 5 1 Shelf(M) 30278A9150 Wire, White MIDDLE Shelf(B) 30278A9000 Wire, White BOTTOM Shelf(A) 30278G0111 Wire, White TOM 3 Shelf(B) 30278G0401 Wire, White BOTTOM 1 Shelf Bracket 30220A0200 Front Center White 2 1 1 Shelf Clip(E) 30220A0700 PP TOP 36 24 24 Shelf Clip(D) 30220A0600 Nylon BOTTOM 36 24 24 Shelf Standard 3022000703 Sides & Back of Cabinet White 4 4 4 Shelf Support 30253A0500 Back Center
PARTS LIST Part Name Model 11RV 14RV 14CRV 22RV 22CRV Part Number Description Ballast 30200F7300 25Watt x R-1P825TP Ballast 30200G7300 25Watt x R-1P825TP Ballast 30200A0141 13Watt x 1DD22B Ballast 30200H7400 17Watt x R-1P817-TP 1 1 Ballast 30200H7300 32Watt x R-1P32-TP 1 1 Lamp 30236A0500 25Watt F25T8/TL95036” Lamp 30236F0500 13Watt F13T8’ CW12” Lamp 30236H0500 17Watt F17T8/TL95024” 1 1 Lamp 30200D0500 32Watt F32TB/TL85048” 1 1 Lamp Shield 30211K0200 PC, T0.
8. REPLACEMENT OF MAIN COMPONENTS 1. LAMP FOR ADVERTISING PANEL(TGM-69R, 48R, 45R, 35R, 33R) 1. Separate the Sign Frame End. 2. Separate the Sign Panel. 3. Separate the Lamp Socket. 4. Separate the Lamp out of the Lamp Holder and replace it.
REPLACEMENT OF MAIN COMPONENTS 5. Take out the Clamp securing wires. 6. Separate the Ballast Connectors. 7. Unscrew two screws securing the Ballast and replace it.
REPLACEMENT OF MAIN COMPONENTS 1. LAMP FOR CABINET LINER(TGM-69R, 48R, 45R, 35R, 33R) 1. Take out the Doors and separate the Lamp from the Lamp Holder. 2. Separate the Lamp Socket.
REPLACEMENT OF MAIN COMPONENTS 3. Separate the Lamp Shield End Cap. 4. Replace the Lamp.
REPLACEMENT OF MAIN COMPONENTS 1. LAMP(TGM-22R,14R) 1. Unscrew four screws securing the Sign Frame End and separate the Sign Frame End. 2. Separate the Sign Panel. 3. Separate the Lamp Sockets and replace the Lamp.
REPLACEMENT OF MAIN COMPONENTS 4. Separate connector of the ballast. 5. Unscrew two screws securing the Ballast. 6. Separate the Lamp Sockets to replace the Lamp for Cabinet Liner. 7. Separate the Lamp Shield End Cap and replace the Lamp.
REPLACEMENT OF MAIN COMPONENTS 1. LAMP BASE ASSEMBLY FOR VERTICAL LAMP SERIES TGM-11RV TGM-14RV, TGM-22RV 1. UNSCREW THE SCREWS OF THE HOUSING COVER TGM-11RV TGM-14RV, TGM-22RV 2. PULL OUT THE HOUSING 3. UNSCREW THE SPECIAL BOLT THAT IS FIXING THE LAMP BASE ASSEMBLY (3POINTS) 4.
REPLACEMENT OF MAIN COMPONENTS 5. SEPARATE THE FLUORESCENT LAMP FROM THE LAMP HOLDER 6. PULL OUT THE LAMP CAP FROM THE LAMP CASE 7. REPLACE THE FLUORESCENT LAMP AFTER PULL OUT THE FLUORESCENT LAMP FROM THE LAMP CASE.
REPLACEMENT OF MAIN COMPONENTS 1. LAMP(TGM-11R,5R) 1. Unscrew two screws securing the Lamp Shield. 2. Disassemble the Lamp Shield. 3. Separate the Lamp out of the Lamp Holder and replace it.
REPLACEMENT OF MAIN COMPONENTS 2. THEMPERATURE CONTROL AND LIGHT SWITCH(TGM-69R, 48R, 45R, 35R, 33R) 1. Unscrew four screws securing the Thermostat control plate. 2. Pull out the Thermostat control plate. 3. Separate the Receptacles out of the Thermostat and Lamp Switch. 4. Separate the Tube of Thermostat from the Evaporator.
REPLACEMENT OF MAIN COMPONENTS 5. Separate the Thermostat Knob out of the Thermostat. 6. Unscrew two screws securing the Thermostat. 7. Separate the Thermostat out of the Thermostat plate. 8. Unscrew two screws securing the Thermostat out of the Thermostat Bracket.
REPLACEMENT OF MAIN COMPONENTS 2. THERMOSTAT CONTROL AND LIGHT SWITCH (TGM-14R, 14RV) 1. Unscrew two screws securing the Thermostat Plate. 2. Pull out the Thermostat Plate. 3. Separate the Receptacles out of the Thermostat and Light Switch.
REPLACEMENT OF MAIN COMPONENTS 4. Separate the Tube of Thermostat from the Evaporator. 5. Separate the Thermostat out of the Thermostat Plate. 6. Unscrew two screws securing the Thermostat out of the Thermostat Bracket.
REPLACEMENT OF MAIN COMPONENTS 2. THEMPERATURE CONTROL AND LIGHT SWITCH(TGM-11R, 11RV) 1. Unscrew six screws securing the Duct. 2. Unscrew four screws securing the Thermostat Plate. 3. Separate the Receptacles out of the Thermostat and Lamp Switch.
REPLACEMENT OF MAIN COMPONENTS 4. Separate the Tube of Thermostat from the Evaporator Coil. 5. Pull out the Thermostat plate. 6. Separate the Thermostat out of the Thermostat plate.
REPLACEMENT OF MAIN COMPONENTS 2. THEMPERTURE CONTROL AND LIGHT SWITCH(TGM-5R) 1. Unscrew two screws securing the Control Box. 2. Separate the Connectors. 3. Unscrew two screws securing the Tube of Thermostat out of the Thermostat Fixture.
REPLACEMENT OF MAIN COMPONENTS 3. EVAPORATOR FAN MOTOR & BLADE(TGM-69R, 48R, 45R, 35R, 33R) 1. Unscrew four screws securing the Thermostat Plate. 2. Unscrew eight screws securing the Duct. 3. Separate the Duct. 4. Unscrew four screws securing the Evaporator Drain Pan.
REPLACEMENT OF MAIN COMPONENTS 5. Separate the Evaporator Drain Pan. 6. Unscrew four screws securing the Evaporator Guide *L, *R and separate them. 7. Separate the Vinyl Cover securing the Evaporator Fan Motor. 8. Separate the Connectors of Evaporator Fan Motor.
REPLACEMENT OF MAIN COMPONENTS 9. Pull out of the Evaporator Fan Motor Harness. 10. Unscrew two screws securing the Evaporator Fan Motor Bracket. 11. Separate the Evaporator Fan Motor Bracket. 12. Unscrew four screws securing the Evaporator Fan Motor out of the Bracket.
REPLACEMENT OF MAIN COMPONENTS 3. EVAPORATOR FAN MOTOR & BLADE(TGM-22R, 22RV) 1. Unscrew the screw securing the Evaporator Fan Motor Guard. 2. Separate the Evaporator Fan Motor Cover. 3. Replace the Evaporator Fan Motor. 4. Unscrew four screws securing the Thermostat Plate.
REPLACEMENT OF MAIN COMPONENTS 5. Separate the Thermostat Plate. Pull out the tube of Thermostat out of the Evaporator Coil. 6. Unscrew four screws securing the Duct. 7. Separate the Duct.
REPLACEMENT OF MAIN COMPONENTS 3. EVAPORATOR FAN MOTOR & BLADE(TGM-14R, 14RV) 1. Unscrew the screws securing the Thermostat Plate and two screws securing the Duct. 2. Separate the Duct. (Caution: Pulling the Duct in to the front can cause the Fan Blade to be bent.) 3. Unscrew four securing the Evaporator Fan Motor Bracket. 4. Separate the Connectors of Fan Motor, the Nut and replace the Fan Blade.
REPLACEMENT OF MAIN COMPONENTS 5. Unscrew two screws securing the Evaporator in case of replacing it. 6. Separate Suction Pipe Cover on the Rear Cabinet. 7. Separate the Sealing Tube. 8. Replace the Suction Pipe with welding machine.
REPLACEMENT OF MAIN COMPONENTS 9. Pull out the Evaporator Coil. (Caution: Pulling the Evaporator can cause the Cabinet Liner to be scratched.) 10. Separate the Evaporator Coil out of the Evaporator Drain Pan and repair the Evaporator Coil.
REPLACEMENT OF MAIN COMPONENTS 3. EVAPORATOR FAN MOTOR & BLADE(TGM-11R, 11RV) 1. Unscrew the screws securing the Duct. 2. Unscrew the screws securing the Thermostat Plate. 3. Separate the harness out of the Thermostat and Lamp Switch. 4. Separate the Evaporator Fan Motor Bracket.
REPLACEMENT OF MAIN COMPONENTS 4. CONDENSER FAN MOTOR & BLADE(TGM-69R, 48R, 45R, 35R, 33R) 1. Unscrew four screws securing the Bottom Grill. 2. Separate the Compressor Harness out of the Switch Box. 3. Unscrew four screws securing the Compressor Base. 4. Pull the Compressor Base and separate the Condenser Fan Motor.
REPLACEMENT OF MAIN COMPONENTS 4. CONDENSER FAN MOTOR & BLADE(TGM-22R, 22RV) 1. Unscrew four screws securing the Bottom Grill. 2. Separate the Connector out of the Switch Box. 3. Unscrew four screws securing the Compressor Base. 4. Pull the Compressor Base and separate the Condenser Fan Motor.
REPLACEMENT OF MAIN COMPONENTS 4. CONDENSER FAN MOTOR & BLADE(TGM-14R, 14RV, 11R, 11RV) 1. Unscrew four screws securing the Bottom Grill. 2. Separate the Connector out of the Switch Box. 3. Unscrew four screws securing the Condenser Fan Motor Bracket. 4. Pull the Condenser Fan Motor with care.
REPLACEMENT OF MAIN COMPONENTS 5. Separate the Fan Motor Bracket. 6. Separate the nut and replace the Fan Blade.
REPLACEMENT OF MAIN COMPONENTS 5. DOOR(TGM-22R, 22RV, 14R, 14RV) 1. Separate the Sign Frame End and Sign Panel. 2. Separate the Door Hinge Top and Door.
Commercial Freezer Service Manual Model No.
1.
FEATURE CHART • Model : TGF-23F SIGN PANEL FLUORESCENT LAMP DOOR ASSEMBLY POWER SWITCH LAMP SWITCH < FRONT > EVAPORATOR FAN MOTOR BLADE • Model : TGF-23F EVAPORATOR FAN MOTOR EVAPORATOR COIL BACK GUARD (AIR BAFFLE BACK) SHELF DOOR HANDLE BOTTOM GRILLE CASTER(WITH BRAKE) CASTER COMPRESSOR CONDENSER COIL CONDENSER FAN MOTOR < SIDE > 90
FEATURE CHART • Model : TGF-9F/13F DOOR ASSEMBLY (1DOOR:TGF-9F) (2DOOR:TGF-13F) DOOR RAIL(ONLY TGF-13F) DOOR HANDLE TEMPERATURE CONTROL (IN THE SIGN PANEL) LAMP SWITCH SIGN PANEL DECORATION COVER *LEFT DECORATION COVER *RIGHT FRONT GLASS < FRONT > LAMP HOLDER • Model : TGF-9F/13F LAMP SOCKET BALLAST LAMP LAMP SWITCH LINER COVER INSULATOR *TOP LINER COVER HEATER EVAPORATOR URT FOAM ASSEMBLY EVAPORATOR * TOP RUNNING CAPACITOR STARTING CAPACITOR SWITCH BOX CASTER(BRAKE) CASTER < SIDE > 91
FEATURE CHART • Model : TGF-9F/13F COMPRESSOR DRYER CONDENSER FAN MOTOR CONDENSER COIL POWER CORD COMPRESSOR COMPRESSOR RELAY ASSEMBLY < BACK > 92 REAR GRILL
2.
PART DETAILS Duct (TGF-23F) Evaporator Fan Motor Guard Duct (A) Duct (B) Evaporator, Fan (TGF-23F) Lamp & Fan Motor Connectors Evaporator Fan Motor Blade Evaporator Coil Evaporator Thermal Defrost Heater F-Sensor 94 Heater Connectors & Sensor Connectors
3.
WIRING DIAGRAM • Model : TGF-13F • Model : TGF-9F 96
4. SPECIFICATION OF MAIN COMPONENTS 1. COMPRESSOR MODEL PART NAME PART NO. HORSE POWER TGF-49F CAJ2464Z 30200R1900 3/2 HP TGF-23F CAJ2432Z 30200R1000 2/3 HP TGF-13F AEZ2415Z 30200N4400 1/3 HP TGF-9F HBL27YE-1 3952127G10 1/4 HP CAPACITY TYPE OF MOTOR INPUT CSR 1,232W CSR 810W CSIR 280W TECUMSEH (FRANCE) TECUMSEH (FRANCE) TECUMSEH (FRANCE) CSR 220W DAEWOO 6,452 BTU/h (1,626 Kcal/h) 3,200 BTU/h (807 Kcal/h) 1,459 BTU/h (368 Kcal/h) 896 BTU/h (226 Kcal/h) MAKER 2.
SPECIFICATION OF MAIN COMPONENTS 6. TEMPERATURE CONTROL MODEL TGF-13F TGF-9F PART NAME PART NO. TYPE MAKER GNF-107DC 30283D0700 NORMAL SHINHAN Spec. 600W 445W MAKER SANGDO SANGDO 7. EVAPORATER DEFROST HEATER MODEL TGF-49F TGF-23F PART NAME SHEATHED HEATER SHEATHED HEATER PART No. 30228L0700 30228L0802 8. BALLAST MODEL TGF-49F TGF-23F TGF-13F TGF-9F PART NAME MAGNETEK 949-LH-TC-P B232I120RH-A 703-L-TC-P 949-LH-TC-P M-132R120C 727-L-TC-P PART NO.
5. ELECTRONIC CONTROLLER INSTRUCTION Section 5 is for TGF-23F/49F 5-1-1. HOW TO USE THE DISPLAY PANEL(TGF-23F) - InsideTemperature can be set by the user. - Not controllable during Turbo Freeze mode. - The default temperature setting is '-7˚F' - By pushing up/down button, you can set the inside temperature from '5˚F' to '-17˚F' LAMP SWITCH POWER SWITCH TEMPERATURE Turbo air LAMP Long Beach, CA T.F.
ELECTRONIC CONTROLLER INSTRUCTION Section 5 is only for TGF-23F/49F 5-1-2.
ELECTRONIC CONTROLLER INSTRUCTION 5-2. FUNCTION TABLE No Control Function Control Objects Contents Remark 1 Initial Operation Buzzer Fan Lamp 88 LED 1. Buzzer will be ring within 2 seconds when you plugged-in and turned on the power switch. 2. 88 LED displays inside temperature. 3. Compressor will be run if evaporator's temperature is higher than 38.3˚F(3.5˚C), compressor will not run for 3 minutes when you plugged-in. 4.
ELECTRONIC CONTROLLER INSTRUCTION No 3 Control Function Control Objects Turbo Freeze Compressor Evap-Fan Motor Con-Fan Motor LED Contents Remark 6. If you press the Turbo Freeze button during the defrost mode, display panel displays Turbo Freeze mode but actually The Turbo Freeze mode will start after defrost mode is completed. 7. If defrost mode occurs during the Turbo Freeze mode, the defrost mode will start after the Turbo Freeze mode is completed TEMPERATURE Turbo air LAMP Long Beach, CA T.F.
ELECTRONIC CONTROLLER INSTRUCTION No 5 Control Function Control Objects Defrost Function Heater Compressor Evap-Fan Motor Con-Fan Motor Contents Remark f. If Defrost Heater's on time exceeds 40 minutes for any reason, a back-up defrost termination switch is also provided. g. If D-sensor's temperature does not reach 47˚F(8˚C) in 40 minutes, error code will be recorded on a MICOM. TEMPERATURE Turbo air LAMP Long Beach, CA T.F. FAN POWER DOOR TURBO FREEZE C. Pause step a. Time = 3 min. b.
ELECTRONIC CONTROLLER INSTRUCTION No 12 Control Function Control Objects Fuzzy Deforst Heater Compressor Evap-Fan Motor Con-Fan Motor Contents Remark The Defrost step will be started at following conditions. 1. The compressor has run for 30 minutes. 2. There is no openning the door for 30 minutes. 3. The temperature of D-sensor is lower than 5˚F. 4. The temperature of F-sensor is higher than D-senser's temperature by 53.6˚F for 10 minutes. 5-3.
6. PARTS LIST Part Name Part Number Description 49F Casters Caster Caster with Brake Caster Caster 30265L0400 30265L0300 30265H0100 30265H0200 TP5040-22-HDP TP5040-22-HDP-TLB 1/2" Stem (TP3625-21-HR) 1/2" Stem (TP3625-21-HR-TLB) 2 2 Compressor Compressor Compressor Compressor Compressor PowerRelay(Comp.
PARTS LIST Part Name Part Number Description Evaporator Evaporator Coil Evaporator Coil Evaporator Sensor (D-senser+F-Senser) Evaporator Sensor (D-senser+F-Senser) Evaporator Thermal Fuse Evaporator Drain Pan Heater Evaporator Drain Pan Heater Evaporator Defrost Heater Evaportaor Defrost Heater Drain Hose Heater Drain Hose Heater Drain Pan Insulator Drain Pan Insulator Evaporator Fan Motor Guard Evaporator Fan Motor Blade Evaporator Fan Motor Duct(A) Duct(B) Duct(A) Duct(B) Evaporator URT Foam Assembly E
PARTS LIST Part Name Part Number Description Lamp Socket Bracket Lamp Shield Fixture Door Handle Door Rail (Middle) 30206R1000 30220R1100 30226A0101 30287N0201 SPG, Painting EGI, Painting Slide, ABS Plastic, Gray PVC-H SignPanel Ballast Ballast Ballast Ballast Lamp Lamp Lamp Lamp Lamp Sign Panel Sign Panel Lamp Holder Lamp Switch Lamp Socket Lamp Socket Decoration Cover (Left) Decoration Cover (Right) Sign Panel Lamp Holder Door Switch Lamp Socket Lamp Socket Sign Frame*Top Sign Frame*Bottom Sign Fram
PARTS LIST Part Name Transformer Ballast Part Number Description 30284L0100 30200R3102 DWS-115U 949-LH-TC-P(MAGNETEK) Shelf ShelfStandard Shelf *L Shelf *R Shelf ShelfClip BackGuard (AirBaffleBack) 30220L1001 30250R0600 30250R0500 30278R0100 30220L0900 30250R0200 SUS304-2B SWRM-B SWRM-B Wire, White PA-6 Wire, White Thermostat Themperture Control 30283N0100 GNF-107DC(SHINHAN) 108 49F 1 1 Model 23F 13F 1 1 9F 4 4 4 4 16 2 1 1
7. REPLACEMENT OF MAIN COMPONENTS 7-1. BOTTOM GRILLE PARTS(TGF-23F) - MAIN PCB, TRANSFORMER, POWER RELAY - DISPLAY P.C.B. - LAMP SWITCH, POWER SWITCH A. Remove Bottom Grille by unscrewing the four screws. B. Remove the Bracket of Display P.C.B.
REPLACEMENT OF MAIN COMPONENTS C. Disconnect Connectors and receptacles. - Replace the Power Switch, Lamp Switch or Display P.C.B. D. Remove the electrical box (Switch Box) cover.
REPLACEMENT OF MAIN COMPONENTS E. Remove the Fixture. F. Replace the Ballast. (for inner Cabinet Lamp. 110W) 1. Pull out the Ballast Base. 2. Replace the Ballast.
REPLACEMENT OF MAIN COMPONENTS G. Replace the Main P.C.B. Transformer and Power Relay. 1. Pull out the Base. 2. Replace the parts.
REPLACEMENT OF MAIN COMPONENTS 7-2. REPLACING DOOR (TGF-23F) A. Disassemble bottom grille as described section 7-1, A, B, C, D. B. Disconnect the door heater wire and lamp wire. Door Heater Wire Lamp Wire C. Remove the Sign Frame (Left, Right) by unscrewing the four screwes of each side.
REPLACEMENT OF MAIN COMPONENTS D. Pull out sign panel to the Right Side. F. Remove the sign panel frame *Bottom.
REPLACEMENT OF MAIN COMPONENTS E. Remove the harness of door switch. - Replace door Switch. G. Remove the door hinge top. H. Lift the door and pull out the door wires.
REPLACEMENT OF MAIN COMPONENTS 7-1. TOP ADVERTISING PANEL (TGF-49F) - MAIN PCB, TRANSFORMER - LAMP SWITCH, POWER SWITCH - DISPLAY P.C.B A. Remove the Sign Frame by unscrewing two screwes of left side. B. Pull out the sign panel from left side.
REPLACEMENT OF MAIN COMPONENTS C. Replace the TRANSFORMER. D. Grip the fixture with long nose and pull out the Main P.C.B. - Replace the Main P.C.B.
REPLACEMENT OF MAIN COMPONENTS E. Disconnect Connectors and receptacles.
REPLACEMENT OF MAIN COMPONENTS 7-2. BOTTOM GRILLE PARTS (TGF-49F) - POWER RELAY - BALLAST(For Inner Cabinet Lamp) A. Remove the Bottom Grill by unscrewing four screws. B. Unscrew the cover plate each side.
REPLACEMENT OF MAIN COMPONENTS C. Disconnect receptacles and unscrew two screws. - Replace the Power relay D. Remove the Drain case. - Pull out the Drain case.
REPLACEMENT OF MAIN COMPONENTS E. Unscrew two screws on the Ballast bracket. (for Inner Cabinet Lamp.
REPLACEMENT OF MAIN COMPONENTS 7-3. REPLACEING DOOR (TGF-49F) A. Disassemble bottom grill as described section 7-2, A. B. Disconnect Left(right) Door heater wires. Door Heater Wire Door Heater Wires (LEFT, RIGHT) C. Disconnect Left (Rigft) Door switch wires.
REPLACEMENT OF MAIN COMPONENTS D. Unscrew the Sign Frame. (Bottom) - Remove Sign Frame (Bottom) E. Remove the door hinge(top). - Lift the door and pull out the door wire.
REPLACEMENT OF MAIN COMPONENTS 7-4. REPLACING Inner Cabinet Lamp (TGF-49F) A. Unscrew the top shelf bracket and Pull out it. B. Unscrew a bottom screw and separate the shelf bracket.
REPLACEMENT OF MAIN COMPONENTS C. Unscrew the lamp top cover and separate lamp cover. D. Lift the fluorescent lamp and pull out it.
