Turbo Air Speeds up the Pace of Innovation Super Deluxe Series Refrigerators & Freezers Installation and Operation Manual Please read this manual completely before attempting to install or operate this equipment Full Stainless Steel Interior and Exterior SOLID DOOR REFRIGERATORS TSR-23SD* TSR-35SD TSR-49SD TSR-72SD SOLID DOOR FREEZERS TSF-23SD TSF-35SD TSF-49SD TSF-72SD www.turboairinc.
CONTENTS PAGE 1. SPECIFICATIONS .......................................................................................... 2 2. SERIAL NUMBER ........................................................................................ 2 3. INSTALLATION ............................................................................................ 3 4. CLEANING & CAUTION ...............................................................................4 5. BASIC OPERATION 5-1. REFRIGERATORS ..........................
INSTALLATION 1. GOOD AIR CIRCULATION - Be sure to avoid any partition and object which may stop the air flow - Be sure that air space is allowed to flow the rear of the unit (Turbo Air recommends that the rear of the unit would be no less than 5 inches from the wall) 2. PLACE ON STRONG GROUND - Be sure that the location be chosen has a storng enough floor to support the total weight of the cabinet and any other contents 3. DO NOT PLAVE NEAR HEAT - Be sure to avoid hot corners and locations near stoves.
CLEANING 1. CLEANING THE INTERIOR AND EXPERIOR - The interior and exterior of the unit can be cleaned using warm water with soap - Don not use an abrasive cleaner becasue it will scratch the stainless steel surface 2. CLEANING THE CONDENSER FINS - To maintain proper refrigeration performace, the Condenser coil must be free of dust, dirt, and grease. This will require periodic cleaning. Condenser fins should be cleaned every three months (90 days) or as needed 3.
BASIC OPERATION TSR-23SD* TSR-35SD TSR-49SD TSR-72SD REFRIGERATORS 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run. 2. The default temprature setting is No.”5”. 3. The compressor is automatically cycled by the electronic controller (PCB, D-Senser). 4. The Defrost cycle is automatically controlled by the R-sensor, and the PCB. 5.
DISPLAY PANEL OF REFRIGERATOR TEMP. SETTING TEMP. CONTROL BUTTON (SEE TO PAGE 7) INNER TEMP. (SEE TO PAGE 8) 3 2 1 4 ˚F 5 6 7 8 9 TEMPERATURE T.C.
TURBO COOLING 1. If you push the T.C. (Turbo Cooling) button, the compressor will run continuously until D-Senser detect 14˚F (-10˚C) to bring down the temperature more quickly. (max.comp.run time = 120 min.) 2. If you push the T.C. button again during Turbo Cooling mode, the compressor will return to the normal operation. 3. During the Turbo Cooling mode works, the temperature Up/Down button will not affect the compressorʼs operation.
INNER TEMPERATURE DISPLAY 1. It displays the inside temperature. 2. Display range is 14˚F to 69˚F (-10˚C ~ +20˚C). 3. When the inside temperature is lower than 14˚F, the panel will display ʻ and, higher than 69˚F, the panel will display ʻ ʼ. ʼ. FAN RUNNING INDICATOR 1. If the fan motor is running, fan running indicator will be turned on. 2. Evaporator fan motor is activated when the door (both doors for TSR-49SD, all three doors for TSR-72SD) is closed. DOOR OPENING INDICATOR 1.
BASIC OPERATION TSF-23SD TSF-35SD TSF-49SD TSF-72SD FREEZERS 1. Plug in and turn on the power switch located on the bottom of the top grille right side. The Display panel will be lighted and make a beep sound. The compressor will begin to run. 2. The default temprature setting is No.”5”. 3. The compressor is automatically cycled by the electronic controller (PCB, F-Senser). 4. The Defrost cycle is automatically controlled by the D-sensor, and the PCB. 5.
DISPLAY PANEL OF FREEZER TEMP. SETTING TEMP. CONTROL BUTTON (SEE TO PAGE 11) INNER TEMP. (SEE TO PAGE 12) 3 2 1 4 ˚F 5 6 7 8 9 TEMPERATURE D.F.
MANUAL DEFROST 1. If you push MANUAL DEFROST button for 5 seconds, the Defrost will start. 2. During the Manual Defrost mode, the Up/Down button for the temperature control can not make the compressor cycle ON or OFF. 3. If you want to change the Manual Defrost mode to the normal mode, push MANUAL DEFROST button for 5 seconds. UP/DOWN BUTTON (Temperature control button) 1. By pushing the up/down button, you can set the inside temperature level from ʻ1ʼ to ʻ9ʼ. 2.
INNER TEMPERATURE DISPLAY 1. It displays inside temperature. 2. Display range is -50˚F to 50˚F (-45˚C ~ +10˚C). 3. When inside temperature is lower than -50˚F, the panel will display ʻ and, higher than +50˚F, the panel will show ʻ ʼ. ʼ. FAN RUNNING INDICATOR 1. If the fan motor is running, fan running indicator will be turned on. 2. Evaporator fan motor is activated when the door (both doors for TSF-49SD, all three doors for TSF-72SD) is closed. DOOR OPENING INDICATOR 1.
TROUBLESHOOTING SYMPTOMS CAUSES SOLUTIONS Freezer is melting food • The controller is set too high to contain food fresh. • Turn the temperature dial to a warmer position. The unit does not refrigerate at all • There is a power connection failure problem. • Check the power cord and plug in it correctly. The unit does not refrigerate well • The unit is in sunlight or near a • Check the installation place. heating device. • Check the condition of stored • The unit contains hot food or too food.
MANUFACTURING COMPANY THREE YEAR WARRANTY Turbo Air warrants to the original purchaser of every new Turbo Air refrigerated unit, the cabinet and all parts thereof, to be free from defects in material or workmanship, under normal use and service, for a period of three (3) year from the date of original installation or 39 months after shipment date from Turbo Air , whichever occurs first.
What is NOT covered by this warranty Turbo Airʼs sole obligation under this warranty is limited to either repair or replacement of parts, subject to the additional limitations below. This warranty neither assumes nor authorizes any person to assume obligations other than expressly covered by this warranty. 1. WARRANTY IS NOT TRANSFERABLE. This warranty is not assignable and applies only in favor of the original purchaser/user to whom delivered.
Warranty Claims... All claims for parts or labor must be made directly thorough Turbo Air. All claims should include: model number of the unit, the serial number of the cabinet, proof of purchase, date of installation, and all pertinent information supporting the alleged defect. In case of compressor replacement under warranty, either compressor or compressor tag must be returned to Turbo Air along with above listed information. Failure to comply with warranty policies will result in voiding claims.