Model : IA-300 ADSL PC Network Interface Modem Installation Guide Microsoft Windows 95, 98, and NT4.0 44-060017-000 V1.
TABLE OF CONTENTS System Requirements ................................................................................................. 1 Before Installation........................................................................................................1 Hardware Installation ....................................................................................................1 Software Installation and Service configuration................................................................
Model : IA-300 Installation Guide SYSTEM REQUIRMENTS Make sure your PC system meets ALL of the following minimum hardware and software requirements: Hardware: q IBM PC/AT or compatible q Pentium 100Mhz or faster q 30Mbytes available hard disk space or more q 2x CD-ROM drive or better q 32Mbyte available system memory or more Software: Your Operating System must be one of the following: ü Microsoft Windows 95.x – 95A, 95B ü Microsoft Windows 98.
Model : IA-300 Installation Guide POINT TO POINT SERVI CE FOR WINDOWS 95A 1. After installing the IA-300 card, power on the PC system. The Hardware Wizard will detect the card as a PCI Network Controller. Select the Driver from disk provided by hardware manufacturer option. Click OK. 2. Insert the IA-300 Driver CD into the CD-ROM drive. 3. The Install From Disk window appears. Enter the :\Drivers\ Win95_98\ PPPoA (e.g. D:\Drivers\Win95_98\PPPoA), then click OK. 4.
Model : IA-300 Installation Guide POINT TO POINT SERVI CE FOR WINDOWS 95B 1. After installing the IA-300 card, power-up the PC system. The Hardware wizard will detect the IA-300 as a PCI Network Controller, click Next. 2. Insert the CD labeled IA-300 Driver into your CD-ROM drive. Then click Other Locations. NOTE: If the driver is not detected, click Back, insert the IA-300 Driver CD, then click NEXT. 3. When the Select Other Location window appears, enter :\Driver\PPPoA9x (e.g. D:\Dr
Model : IA-300 Installation Guide POINT TO POINT SERVI CE FOR WINDOWS 98, 98A 1. After installing the IA-300 card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. 2. Then select Search for the best driver for your device. (Recommended), click Next. 3. Insert the CD labeled IA-300 Driver into your CD drive. 4. Then select Specify a location and enter :\Drivers\Win98SE\PPP
Model : IA-300 Installation Guide 16. Enter the User Name and Password supplied by the Internet service provider. Click Connect. 17. The message Logging on to network confirms a valid user name, password, and VPN IP address. Please wait for the Connection Established window before proceeding. Note: If logon domain is required, enter username, password and logon domain supplied by your ISP. 18. The PPPoA service connection is now established.
Model : IA-300 Installation Guide Point to point Service for windows nt 4.0 NOTE: To perform the installation logon as Administrator. Also the TCP/IP protocol must be installed prior to the driver installation. 1. At the desktop, double click My Computer, then double click Control Panel . 2. In the Control Panel window, double click the Network icon then select the Adapters tab. 3. Click Add (to add new adapters). 4. In the Select Network Adapter window click Have Disk. 5.
Model : IA-300 Installation Guide 16. The PC system needs to be restarted for the changes to take effect. Click Yes 17. After the system restarts the Diagnostic Tools icon will appear on the task bar. When the IA-300 card is connected to the ADSL data port, both panels of the icon will appear black signifying an ADSL connection. 18. To begin a dial-up connection, double-click My Computer, then double-click Dial-Up Networking. 19. If this is the first dial-up connection created enter an area code (e.g.
Model : IA-300 Installation Guide PPPoA ADSL NETWORK CONNECTION NOTE: This section is for Win95A, 95B and 98 users only. 1. Double click the My Computer icon on the desktop. Then double click the Dial-Up Networking icon. The Dial-Up Networking window will appear. NOTE: Another dialog window may prompt for the entry of the Area Code if this is a first time Network connection. Enter the Area code and click OK. 2. Double-click on the Make New Connection icon. 3. Enter the connection name (e.g.
Model : IA-300 Installation Guide IP OVER ATM SERVICE FOR WINDOWS 98 2ND EDITION nd NOTE: This section is for Windows 98 2 Edition only. 1. After installing the IA-300 card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. 2. Then select Search for the best driver for your device.(Recommended)., click Next. 3. Insert the CD labeled IA-300 Driver into your CD-ROM drive. 4.
Model : IA-300 Installation Guide 15. The Select Network Component Type window appears. Select Protocol, and click Add. The Select Network Protocol window appears. In the Manufactures section, select Microsoft. In the Network Protocols section, select TCP/IP then click OK. 16. Back at the Network window, scroll through the installed network component window and select TCP/IP à ITeX ADSL PCI NIC.
Model : IA-300 Installation Guide Bridged Ethernet service for Windows 95A 1. After installing the IA-300 card, power on the PC system. The Hardware Wizard will detect the IA-300 as a PCI Network Controller. Select the Driver from disk provided by hardware manufacturer option. 2. Insert the IA-300 Driver CD into the CD-ROM drive. 3. The Install From Disk window appears. Enter the :\Drivers\Win95_98\BEoA (e.g. D:\Drivers\Win95_98\BEoA), then click OK. 4.
Model : IA-300 Installation Guide BRIDGED ETHERNET SERVICE FOR WINDOWS 95B 1. After installing the IA-300 card, power-up the PC System. 2. The Hardware wizard will detect the IA-300 as a PCI Network Controller, click Next. Insert the IA-300 Driver CD into the CD-ROM drive. Click Other Locations. 3. When Select Other Location window appears, enter :\Drivers\Win95_98 \BEoA (e.g. D:\Drivers\Win95_98\BEoA) and click OK. 4. The Update Device Driver Wizard window appears. Click Finish.
Model : IA-300 Installation Guide BRIDGED ETHERNET FOR WINDOWS 98, 98A 1. After installing the IA-300 card and restarting the system, the Add New Hardware Wizard window will automatically appear and indicate that a new PCI Network Controller has been found. Click Next. 2. Then select Search for the best driver for your device. Click Next. 3. Insert the CD labeled IA-300 Driver into your CD-ROM drive. 4. Then select Specify a location, enter :\Drivers\Win95_98\BEoA (e.g. D:\Drivers\W
Model : IA-300 Installation Guide BRIDGED ETHERNET ADS L SERVICE CONFIGURATION This section describes how to configure the ADSL network service when your PC is running Microsoft Windows 95A, 95B, 98, 98A. 1. Double click My Computer, Control Panel , and then Network. 2. In the Network window, select the Configuration tab. 3. Scroll through the installed network components list. Highlight the TCP/IP-> ITeX ADSL PCI NIC and click Properties.
Model : IA-300 Installation Guide Congratulations, you are done.
Model : IA-300 Installation Guide BRIDGED ETHERNET FOR WINDOWS NT 4.0 NOTE: To perform the installation logon as Administrator. TCP/IP protocol must be installed prior to the driver installation. At the Network window select the Protocols tab and verify that the TCP/IP is present. 1. At the desktop, double click My Computer, double click Control Panel, double click Network and then select the Adapters tab of the Network window. 2. Click Add (to add new adapters). 3.
Model : IA-300 Installation Guide 15. The Configuration window appears. Select the ADSL Mode option and then select the ADSL mode type provided by your ISP. The service mode type will be one of the following: q ITU G.992.1 Annex A (G.dmt) ....................referred to as G.dmt q ITU G.992.2 Annex A/B (G.lite)..................referred to as G.lite q ANSI T1.413 Issue 2.......................................referred to as ANSI 16. After you select and check your ISP’s service mode, click Set.
Model : IA-300 Installation Guide EDITING BRIDGED ETHERNET ADSL SERVICE CONFIGURATION 1. This section includes the IP configuration specifics for Windows NT4.0. The NT 4.0 windows are slightly different from those of Windows 95/98. Other than these illustrative differences, the process for editing the IP address settings is the same for Windows NT 4.0 and Windows 95/98. 2. At the desktop, double click My Computer, then double click Control Panel to view the contents of the control panel.
Model : IA-300 Installation Guide APPENIDX A - DIAGNOSTIC TOOLS On the Diagnostic Tools icon on the right hand side of the status bar. Right-click the icon to display the menu, then Click Open. The ADSL Diagnostic Tools window appears on the desktop. The three tabs of the Diagnostic Tools are ADSL Status, Diagnostic and ADSL Statistic.
Model : IA-300 Installation Guide The Diagnostic program performs a brief hardware check and displays the hardware status. If the IA-300 fails the Diagnostic tests (shown below), then record the test result and contact customer support.
Model : IA-300 Installation Guide 3 4 Is the NIC constantly trying to negotiate a connection – with blinking yellow panels – but failing to reach ADSL connection? q Select Disconnect from the Diagnostic Tools then try to reconnect. q Restart the PC system and try to reconnect. q Examine the RJ-11 connectors and cable for any deterioration.
Model : IA-300 Installation Guide 11 Driver installation resulted in unexpected errors or warnings, and you can’t connect. q Perform the driver removal procedure. q Verify which version of Microsoft Windows is loaded in the PC system. q Perform the Alcatel Speed Touch PC driver removal procedure q For PPPoA – Reload Dial -Up Network upgrade 1.3 q Install the Alcatel Speed Touch PC driver again.
Model : IA-300 Installation Guide APPENDIX B - UPGRADE MICROSOFT DUN VERS ION 1.3 This section explains how to upgrade Microsoft’s Dial -Up Networking (DUN) application. You can download the DUN application from Microsoft’s Web page and install it into your system. Please follow the instruction below. 1. Access the Microsoft Web site at http://www.microsoft.com. 2. In the Contents frame, select Free Downloads. 3. Scroll to Support Drivers, Patches and Service Packs and select Window 95 Updates.
Model : IA-300 Installation Guide APPENDIX C – VERIFYI NG DIAL-UP NETWORKING (DUN) STATUS 1. It is possible to have Dial-Up Networking (DUN) version 1.2B or above, but not have the Dial-Up Networking components loaded in the Windows environment. This procedure is for determining the status of DUN on the PC system. 2. At the task bar click Start, Settings, Control Panel and double-click on Add/Remove Programs. 3.
Model : IA-300 Installation Guide APPENDIX D – REMOVING IA-300 DRIVERS WINDOWS 95, 98 1. To Delete IA-300 drivers; on the desktop, right -click on My Computer, then select Properties, then click on the Device Manager tab, then double click Network adapters. 2. Select the ITeX ADSL PCI NIC, then click on the Remove button. 3. A warning message “You are about to remove this device from your system.” will appear. Click OK to remove drivers or click Cancel to abort the driver removal. 4.
Model : IA-300 Installation Guide APPENDIX E – VERIFYING / CHANGING THE ADSL MODE NOTE: The default installation ADSL mode is ANSI T1.413 Issue 2 or ANSI. If your ISP is providing a different mode then you need to change the setting. 1. On the right-hand side of the task bar, right click on the Diagnostic Tools icon. Then select Configuration. 2. The Configuration window appears. Select the ADSL Mode option and then select the ADSL mode type provided by your ISP.
Model : IA-300 Installation Guide APPENDIX F - SYSTEM REQUIREMENTS & COMPLIANCE INFORMATION Power Requirements • 0.75A Max @ +5V ± 5%, 0.
Model : IA-300 Installation Guide APPENDIX G – COPYRIGHT & REGULATORY INFO RMATION Copyright 1999, Integrated Telecom Express, Inc. All rights reserved. This manual and software described in it are copyrighted with all rights reserved. This manual may not be copied, in whole or in part, without the written consent of Integrated Telecom Express, Inc. All other product names are trademarks and or registered trademarks of their respective companies.
