TUMBREL USER GUIDE Window Air Conditioner Mounting Support Bracket AC-100 AC-200 THANK YOU FOR PURCHASING THE TURBRO® wind Ow AIR CONDITIONER MOUNTING SUPPORT BRACKET. ® \> Read all instructions before assembling or using this product. Failure to follow instructions may lead to property damage or personal injury. Keep this user manual for future reference.
BOX CONTENTS AC-100 Long Screw (M8 x 70mm) oO 1 Rubber Pad 2 Short Screw (M6 x 50mm) ® 2 Small Wash mall Washer 1 Level Shelf ® ; Hex Nut ax Nu 1 Adjustable Base ® ; User Good ser Guide 3 Flat Spacer 2 Plastic Expansion Anchor jy Flange Hex Bolt (M6 x 100mm) te Support Body 006006860 © wh Support Leg
BOX CONTENTS AC-200 lam Qty.
IMPORTANT SAFEGUARDS ® This product works with single or double hung windows only. It does not work in slider, crank-out or casement windows. The included expansion screws are not suitable for hollow aluminum window sills. 2 Do not overload the bracket in excess of its maximum capacity (AC-100: 100 lbs, AC-200: 200 Ibsen. @ This product is not designed to support the weight of people or animals. Do not place children on the unit or attempt fo use it as a support for any of the above.
INSTALLATION INSTRUCTIONS Installation Side View for 3 Window Types @ ) @ Inside . Outside Inside Quayside Sill with out wall Sill with out wall 7 Outside @ Inside NOTE: If the lip is too thick that the leg of bracket might not be able to reach the outer wall.
INSTALLATION INSTRUCTIONS ® Find the air conditioner's center of gravity. Determine the approximate center of gravity, or If one side is heavier than the other. To do this, set the air conditioner on the ground. Partially lift one side at a time (left and right, not front and back) to determine if the weight is centered, or if the right or left side is heavier. (If both sides feel the mass, weight is ‘balanced’} @ Find the correct window sill position.
INSTALLATION INSTRUCTIONS NOTE: If your air conditioner has an adjustable window panel frame (a), keep moving the support body until the frame fits between it and stool (b). If the A/C shelf contacts the window frame (c), add a flat spacer. NOTE: Build-up may be higher than stool, but the A/C Support will hold. @ Align and Mount to Sill Mark two holes through the base of the bracket onto the sill. If A/C weight is ‘balanced’, use these marks.
INSTALLATION INSTRUCTIONS ® Set the angle Place the end of the leg flat against the underside of the support body. Gradually slide the leg towards the inner end of the shelf until the foot pad rests against the exterior wall. Stop moving leg when the level bubble is centered. Align leg holes with the closest holes in the shelf. Insert the flange hex bolt with washer through holes, temporarily securing leg fo shelf. Hack the level so the bubble is toward you.
INSTALLATION INSTRUCTIONS @ Final Mounting Tighten leg to shelf with hex bolt and hex nut and washer assembly, using wrench or socket {7/16 inch or 10 mm). Be sure the fool pad is flatly secured against the exterior wall. ® Removal Remove A/C unit. Unfasten screws. Remove A/C support and spacer from the sill.
WARRANTY This product is covered by a limited 2-year warranty by TURBO from the date of purchase. ® What is NOT covered? Damage caused by the owner when attempting to fix or alter the product themselves. Damage caused by misuse, abuse, neglect, alterations, or unauthorized repair. Natural depreciation. 2 How fo request warranty services? To obtain the benefit of this warranty, please leave a message online turbro.comicontact), or send an email to ® What will TURBO do? Repair the item.
ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANT ABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. TURBO © Katmai Technology Limited www.
