SAVE THESE INSTRUCTIONS FOR FUTURE USE Tip for First-Time Use When using this fireplace for the first time, or after a long period of storage, let the fireplace run for at least 15 minutes with the thermostat set at the maximum heat level to remove the "new product” smell. This smell is because the fireplace absorbs moisture, creating an odor similar to that of old leather. It will go away after a few minutes of use.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Overheating Protection » This heater has an overheating protection cutoff that switches the appliance off automatically if it overheats. » Obstruction of the front grill may result in overheating. If this occurs, please disconnect the heater from the power socket and allow it to cool for 10-15 minutes before powering it on again. » Should problems persist, please contact TURBO customer service team via [Lg 110-120V / 60Hz Rated Current 12.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Parts List etl, Part LY TL Quantity Part Description Quantity A Firebox 1 E Mounting Bracket A 1 B Glass Panel 1 F Mounting Bracket B 1 Cc Remote Central 1 G Acrylic Crystals 1 set D Ember Bed Strip 1 H Logs 1 set Hardware Contents Description Quantity AA Wall Anchor 4 BB Large Screw 8 cc Small Screw 12 03
SAVE THESE INSTRUCTIONS FOR FUTURE USE WARNINGS + Due to high temperatures, keep the fireplace out of high-traffic locations. +» Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3ft (0.9m) away from the front of the fireplace. » Never install the fireplace where it may fall into a bathtub or other body of water. « Prevent contact with loose insulation. Do not install the fireplace against a vapor barrier or exposed insulation.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Wiring This fireplace can either be plugged into a grounded 3-prong outlet or a hard wire connection. ENS J 4 This product is equipped with a 3-pin polarized plug. Connect to properly grounded outlets only. This unit is for use on 120 volts outlets only. For your safety, please always plug the unit into a wall outlet/receptacle. An extension cord or power tap (outlet/power strip) should never be used with this device.
SAVE THESE INSTRUCTIONS FOR FUTURE USE 3. Use pliers to take the wire clip off and remove the power cord. 4. Insert the Red wire to the designated N Terminal and tighten the screw. Insert the Green or bare copper wire to the designated G Terminal and tighten the screw. Insert the Black wire to the designated L Terminal and tighten the screw. Make sure all connections are tightened properly.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Testing Testing the Fireplace Prior to Installation NOTE: Do not install the glass panel when testing. + Before installing the fireplace, test the fireplace to make sure that it operates properly. + Plug fireplace into approved outlet and power on the fireplace. Once fireplace is tested, continue with the installation.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Mantel Mantel 8" (203mm) 8" (203mm) Wall o Floor Floor Side View (Wall Mount } Side View (recessed into a wall) NOTE: « Before installing the fireplace, please plug fireplace into approved outlet and power on, test the fireplace to make sure that it operates properly. « Do not install the glass panel when testing. « If you have any problems about installation, please contact support team at A.
SAVE THESE INSTRUCTIONS FOR FUTURE USE 4. Insert the Firebox into the opening and adjust the position of the unit until it is centered and level. 5. Attach the Firebox with 4 Large Screws (BB}, on the side wood studs with an electric drill.
SAVE THESE INSTRUCTIONS FOR FUTURE USE 6. Insert the Ember Bed Strip (D) into the base of the Firebox (A). Depending on your preference, place Acrylic Crystals (G) / Log {H) on the Carbon Bed Strip {D). 7. Installing the Glass Panel. NOTE: This glass front is heavy. It is recommended that two people perform the assembly at this step to prevent damage. + Carefully set both hooks of the front glass panel in the firebox.
SAVE THESE INSTRUCTIONS FOR FUTURE USE » Secure the glass front (B) by fastening 4 Small Screw (CC) and complete the installation. Your fireplace is now ready for use! installation 1. To mount the item to the wall, refer to the mounted size of the model below and mark the mounting position on the wall. Using a electric drill bit (not included), drill a pilot hole at each of the marked corners.
SAVE THESE INSTRUCTIONS FOR FUTURE USE 2. Fix the Mounting Brackets at both sides of firebox by 6 Small Screws (CC) as shown. WALL 3. Insert Wall Anchors (AA) to drilled holes, then insert Large Screws (BB) into the Wall Anchor (AA) with an electric drill or screwdriver. Note: Wall Anchors (AA) are not required if you are installing the fireplace directly to studs. It is recommended ~~ to install the mounting brackets to at least one stud if possible. Note: Do not fasten the Large Screws (BB) tightly.
SAVE THESE INSTRUCTIONS FOR FUTURE USE 4. Lift the Firebox(A) and hang the Firebox on to the wall with the Large Screws (BB). (It's recommended that two people lift the firebox to prevent injury or damage) 5. Insert the Ember Bed Strip {D) into the base of the Firebox (A). Depending on your preference, place Acrylic Crystals (G} / Log {H) on the Carbon Bed Strip (D).
SAVE THESE INSTRUCTIONS FOR FUTURE USE 6. Installing the Glass Panel. NOTE: This glass front is heavy. It is recommended 2 people to fulfill the assembly at this step to prevent damage. « Carefully set both hooks of the front glass panel in the firebox. NOTE: Make sure the glass is properly installed according to the direction and steps below, and fully attached to the firebox so that the control panel can work properly.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Control Panel Operation The Control Panel is located in the lower right corner of the fireplace. The function icon lights will tum off after 20 seconds of no operation. Please touch the control panel to wake it up again before using the control panel. Crackling Sound Flame Speed Flame | | | fis] Display Screen REC Heater Ember Bed Power » Power Button « Turn the appliance ON/ OFF. Flame Button + Press the Flame Button to active the Flame Color mode.
SAVE THESE INSTRUCTIONS FOR FUTURE USE « Press and hold the Flame Button for 3s and enter the Flame Brightness mode. The Flame Button will flash. Press again to cycle through different brightness settings of the flame. See the table below for more detailed information. b5 Level 5 ba Level 4 b3 Level 3 b2 Level 2 b1 Level 1 « No operation within 10 seconds to exit the Flame Brightness mode. ©) Ember Bed Button « Press to active the Ember Bed Color mode.
SAVE THESE INSTRUCTIONS FOR FUTURE USE ™ Flame Speed Button This option is invalid on the Flame OFF state. * Press to active the Flame Speed mode. « Press again to cycle through different speed of the flame. See the table below for more detailed information. Level 1 Level 2 Level 3 Level 4 Level 5 Heater Button « Press to active the Heater function. + Press again to cycle through different temperature of the heater. See the table for more detailed information.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Crackling Sound Button This option is Invalid on Flame OFF state. * Press to active the Crackling Sound mode. « Press again to cycle through different level of the crackling sound. See the table for more detailed information. Child Lock Mode +» Press and hold the Ember Bed Button + Crackling Sound Button for 5 seconds to active the Child Lock function.
SAVE THESE INSTRUCTIONS FOR FUTURE USE & Power Button « Turn the appliance ON/ OFF. & Flame Button « Press the Flame Button to tum the Flame LED ON/OFF. « Press Up and Down button to choose the flame color. ©) Ember Bed Button « Press the Ember Bed Button to tum the Ember Bed LED ON/OFF. « Press Up and Down button to choose the ember bed color. Heater Button « Press the Heater Button to turn the Heater ON/OFF. « Press Up and Down button to choose the temperature of the heater.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Child Lock « Press the Child Lock Button to turn the Child Lock function ON/OFF. Note: On the child lock mods, you can tum the appliance OFF by the remote control, and the other keys of the remote control do not work. ™ Flame Speed It is invalid on Flame OFF state. « Press to active the flame speed mode. « Press Up and Down button to chooses the flame speed. A Up Button/ N77 Down Button « Press the Up and Down Button to choose the corresponding setting.
SAVE THESE INSTRUCTIONS FOR FUTURE USE 15.19 Labeling requirements. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 15.21 Information to user.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Cleaning & Maintenance « Always tum the fireplace OFF and unplug the prows cord from the outlet before cleaning, performing maintenance, or moving the fireplace. Failure to do so could result in electric shock, fire, or personal injury. Metal: « Buff using a soft cloth, slightly dampened with a citrus oil-based product. +» Do not use brass polish or household cleaners as these products will damage the metal trim.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Troubleshooting Customer Support: [0] The fireplace doesn't operate Possible Cause(s) The fireplace is not plugged in. [e112 YT Make sure the fireplace is plugged into a standard 120V outlet. A circuit breaker is tripped or a fuse is blown. Check additional appliances on the circuit. Ideally, the fireplace should be on a dedicated 15-amp circuit. The vents are dirty or clogged. Unplug the unit. Clear the vent area of dust and debris.
SAVE THESE INSTRUCTIONS FOR FUTURE USE Warranty Information TURBO provides a 1-year limited warranty for TURBOPROP Heater, from the date of purchase, subject to the following conditions and limitations outlined below. WHAT IS COVERED? « This warranty is limited to the repair or replacement of part(s} proved to be defective in material or workmanship, after said defect is confirmed by the manufacturer's inspection.
