Installation Instructions

ManualsBrandsTurn of the Century ManualsCeiling Fan LightsAnya 11.5" White 15 W LED Ceiling Fan Light

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless

additional support is provided for the fan.

355-3165

131011

Turn of the Century

Coupling

Pull Chain

Cap

Glass Shade

Short Nipple

Rubber Pad

Hex Nut

Metel Pad

Hex Nut

Cover

Finial

LED 15W

Installing the fan light on fans with Non-Removable

switch box:

1. Unscrew the three screws from the switch box, remove

the switch box cover and disconnect the wire nuts.

(See Fig. 1)

2. Push the center plug from inside the switch box cover

to remove the center plug. (See Fig. 1)

Note: Save the center plug should you choose to

remove the light fixture in the future.

3. Feed the two wires from the fan light kit through the

center hole in the switch box cover, and thread the

wires through the washer and hex nut, then secure

switch box cover onto the fan light kit with a hex nut

and washer. (See Fig. 2)

4. Remove the wire nuts from the two wires in the

switch box labeled “FOR LIGHT KIT CONNECTION”.

5. Connect wires by using the wire nuts: (See Fig. 2)

---The black (hot) wire from fan light kit to the blue

(hot) wire from the fan.

---The white (neutral) wire from fan light kit to the white

(neutral) wire from the fan.

---Carefully put wires back into the switch box.

6. Restore the switch box cover back to the switch box by

using the three screws. (See Fig. 2)

7. Slip the short nipple up through the pull chain, and

secure it into the coupling with hex nut. (See Fig. 2)

8. Thread the pull chain from the fan through the fan light,

cap and glass shade, then attach the glass shade

through the pull chain and the short nipple, secure them

with a rubber pad, metel pad and hex nut. (See Fig. 2)

Note: Make sure that the pull chain from fan in a

perpendicular line.

9. Slip the cover up through the pull chain and the short

nipple, secure it with finial. (See Fig. 2)

10. Turn on the electric circuit.

Motor

Switch Box

Hex Nut

Screw

Switch Box Cover

Nipple

Wire Nut

Washer

Center Plug

----This FAN LIGHT can be installed in one of three ways.

----This fan light is not compatiable with ceiling fans

containing an integrated light kit.

Fig.1.

Switch Box Cover

Screw

Switch Box

Fig.2.

Wire Nut

Fan Light

Summary of content (3 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS 355-3165 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan. ----This FAN LIGHT can be installed in one of three ways.
PAGE 2
Installing the fan light kit on a removable switch box: 1. Unscrew the three screws from the fan, remove the switch box and disconnect the terminals. (See Fig. 3) 2. Push the center plug from inside the switch box to remove the center plug. (See Fig. 3) Save the center plug should you choose to remove the light fixture in the future. 3.
PAGE 3
Installing the fan light on the ceiling: hardware package For Semi-Flush 1. Take out the parts from the hardware package For Semi-Flush. (See Fig. 7) 2. Attach two screws to the mounting strap, and secure it with two lock nuts. Adjust the length of the screws if necessary. (See Fig. 7) 3. Attach the mounting strap to the outlet box by using two mounting screws. (See Fig. 7) 4.