Installation Instructions

ManualsBrandsTurn of the Century ManualsCeiling Fan Lights2-Light Burnished Bronze Ceiling Fan Light Kit with Amber Flake Bowl

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless

additional support is provided for the fan.

355-3170

131016

Turn of the Century

Pull Chain

Glass Shade

Frame

Installing the fan light on fans with Non-Removable

switch box:

WARNING:

As per EPACT 2005 requirements, this fan light has a built-in current

limiting device to conserve energy. The fan light will not operate if the

combined wattage of the installed bulbs exceeds 190 Watts. If the fan

light shuts off shortly after being switched on, it may be due to

excessive current demand. You should replace the light bulbs with

lower wattage bulbs.

1. Unscrew the three screws from the switch box, remove

the switch box cover and disconnect the wire nuts.

(See Fig. 1)

2. Push the center plug from inside the switch box cover

to remove the center plug. (See Fig. 1)

Note: Save the center plug should you choose to

remove the light fixture in the future.

3. Feed the two wires from the fan light kit through the

center hole in the switch box cover, and thread the

wires through the washer and hex nut, then secure

switch box cover onto the fan light kit with a hex nut

and washer. (See Fig. 2)

4. Remove the wire nuts from the two wires in the

switch box labeled “FOR LIGHT KIT CONNECTION”.

5. Connect wires by using the wire nuts: (See Fig. 2)

---The black (hot) wire from fan light kit to the blue

(hot) wire from the fan.

---The white (neutral) wire from fan light kit to the white (neutral) wire from the fan.

---Carefully put wires back into the switch box.

6. Restore the switch box cover back to the switch box by using the three screws. (See Fig. 2)

7. Adjust the arms of the fan light, the arms should be positioned with equal distances between them.

8. Install bulbs(included). See relamping label at socket area or packaging for maximum allowed

wattage.

9. Place the glass shade into the frame as shown, raise the frame and align the three holes on

outside of the frame with three holes on arms of fan light, and secure them with set screws.

10. Thread the light pull chain through the grommet hole (marked “For fan light kit”) on the frame.

11. Thread the fan pull chain through the grommet hole (marked “For fan”) on the frame.

Note: Make sure that the pull chain from fan in a perpendicular line. (See Fig. 2)

12. Turn on the electric circuit.

Motor

Switch Box

Hex Nut

Screw

Switch Box Cover

Nipple

Wire Nut

Washer

Center Plug

----This FAN LIGHT can be installed in one of three ways.

----This fan light is not compatiable with ceiling fans

containing an integrated light kit.

Fig.1.

Switch Box Cover

Screw

Switch Box

Fig.2.

Wire Nut

Fan Light

Set Screw

Bulb Type B Max.60W

(included)

Summary of content (3 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS 355-3170 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan. WARNING: Fig.1.
PAGE 2
Installing the fan light kit on a removable switch box: Fig.3. 1. Unscrew the three screws from the fan, remove the switch box and disconnect the terminals. (See Fig. 3) 2. Push the center plug from inside the switch box to remove the center plug. (See Fig. 3) Screw Save the center plug should you choose to remove the light fixture in the future. Switch Box 3.
PAGE 3
Installing the fan light on the ceiling: hardware package For Semi-Flush 1. Take out the parts from the hardware package For Semi-Flush. (See Fig. 7) 2. Attach two screws to the cross bar, and secure it with two lock nuts. Adjust the length of the screws if necessary. (See Fig. 7) 3. Attach the cross bar to the outlet box by using two mounting screws. (See Fig. 7) 4. Thread the fixture wires through the canopy, metal pad, washer, grounding pad and hex nut. (See Fig. 7) 5.