Installation Instructions

ManualsBrandsTurn of the Century ManualsCeiling Fan Lights3-Light Weathered Patina Ceiling Fan Light Kit with Faux Rawhide Shades

355-7091 --- Page 1

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT

BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless

additional support is provided for the fan.

355-7091

121018

Turn of the Century

Shade

Clip

Candle Tube

Bulb Type B Max.60W

(included)

Installing the fan light on fans with Non-Removable

switch box:

WARNING:

As per EPACT 2005 requirements, this fan light has a built-in current

limiting device to conserve energy. The fan light will not operate if the

combined wattage of the installed bulbs exceeds 190 Watts. If the fan

light shuts off shortly after being switched on, it may be due to

excessive current demand. You should replace the light bulbs with

lower wattage bulbs.

1. Unscrew the three screws from the switch box, remove

the switch box cover and disconnect the wire nuts.

(See Fig. 1)

2. Push the center plug from inside the switch box cover to

remove the center plug. (See Fig. 1)

Note: Save the center plug should you choose to remove

the light fixture in the future.

3. Feed the two wires from the fan light kit through the

center hole in the switch box cover, and thread the wires

through the washer and hex nut, then secure switch box

cover onto the fan light kit with a hex nut and washer.

(See Fig. 2)

4. Connect wires by using the wire nuts: (See Fig. 2)

---The smooth wire (marked) from fan light kit to the

black (hot) wire from the fan.

---The ridged wire (unmarked) from fan light kit to the

white (neutral) wire from the fan.

---Carefully put wires back into the switch box.

6. Restore the switch box cover back to the switch box by

using the three screws. (See Fig. 2)

7. Attach the clips of the shades onto the candle tubes.

(See Fig.2)

8. Install bulbs (included). See relamping label at socket

area or packaging for maximum allowed wattage. (See Fig. 2)

9. Turn on the electric circuit.

Motor

Switch Box

Hex Nut

Screw

Switch Box Cover

Nipple

Wire Nut

Washer

Center Plug

----This FAN LIGHT can be installed in one of three ways.

Fig.1.

Switch Box Cover

Screw

Switch Box

Fig.2.

Wire Nut

Fan Light

Summary of content (3 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS 355-7091 WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless additional support is provided for the fan. Fig.1.
PAGE 2
Installing the fan light kit on a removable switch box: 1. Unscrew the three screws from the fan, remove the switch box and disconnect the terminals. (See Fig. 3) 2. Push the center plug from inside the switch box to remove the center plug. (See Fig. 3) Save the center plug should you choose to remove the light fixture in the future. 3.
PAGE 3
Installing the fan light on the ceiling: Fig.7. Fig.9. Fig.8. Hex Nut Washer Loop 1/2" Nipple-2 Hex Nut Nipple-2 Cap Cap hardware package for chandelier Grounding Tab Ceiling Box House Grounding Wire Wire Nut Hex Nut Washer Mounting Strap Green Grounding Screw Mounting Screw Nipple-1 Canopy Top Loop Collar 1. Attach nipple-1 to the mounting strap, and secure with a Loop Lock washer and a hex nut. (See Fig.9) Chain 2.