User Manual

ManualsBrandsTurnigy Marine ManualsHobbyESC 120A

01 Main features

User Manual

03 Wiring Diagrams

ATTENTION

02 Speciﬁcation

04 Operation Instruction

Normal working mode

05 Programming

1. Enter programming mode：

1.1 Turn on transmitter , move throttle to the full forward position.

1. Connect ESC with batter y, wait for 2 seconds, motor emits shor t“BEEP-BEEP-”twice, it means power up normally.2

1.3 Wait for 5 seconds, motor emits special tone“ ∮12321”,it has entered programming mode.

2.Select setting options:

After entering programming mode, you will hear 5 groups tone which emits in a loop as following sequence .After motor emits a group of tone ,

move the throttle to the neutral( pistol transmitter) / the full down throttle position ( the stick transmitter), it enters this option.

( Note: there is a special tone “∮12321” before the loop tone,“∮12321” is the start of selecting option.)

2.1 Running Mode （1 short tone） “beep-”

2.2 Motor direction adj. （2 short tone） “beep-beep-”

2.3 Low voltage protection （3 shor t tone） “beep - beep - beep -”

2.4 Start Mode (Punch) （4 shor t tone） “beep-beep- beep-beep -”

2.5 Timing （1 long tone） “beep --”

3.Select parameter:

Goes into some one setting option,motor will emit tone in a loop, move the throttle to the forward full position after a cer tain tone, so the

parameter of this option has selected, then motor emits special tone “∮1212”, this parameter has stored.(If don't select other options, move

throttle to the nature position in 3 seconds, then motor emits special tone “∮765765”, exit the program mode. If go on selecting other options,

please return to procedure 2, and select other options).

*Shadow parts are factory default value

Programming with transmitter

Note: Usually,1 long tone"beep--" equals to 5

shor t tone"beep-", for example:1 long tone

"beep--" and 1 short tone “beep-” equals to 6.

Set throttle range

Advise set throttle range when ﬁrst time to use Flycolor ESC.

The feature of Flycolor ESC is that set the best throttle range according to different transmitter, then ESC can get the most smoothly throttle

linear through throttle range of transmitter. To make ESC get and memorize throttle output signal. The process only do once, you need do this

process again after changing transmitter.

FlyM onster

seri es

Thank you for purchasing our brushless electronic speed controller (ESC) . Any improper operation may cause

personal injury and equipment damage. This high power system for RC model can be dangerous ,we strongly

suggest users read the instruction carefully and completely. We will not assume any responsibility for personal

injury ,property damage, or any consequential damages resulting from our product.

(Boat Brushless ESC)

● Use powerful & high performance MCU. Users can set functions as their demand, fully embody Intelligent characteristics. Unique circuit design, strong

anti-interference.

● Waterproof design(Note: if there is water in the ESC, Please dry the water at the connectors).

Start mode can be set. throttle response fast, and it has a very smooth speed control linearity. Compatible with scale boat & racing boat .●

Low-voltage protection threshold value can be set.●

Built-in switch BEC, large power load with servo, lower power dissipation.●

Multiple protection functions: input voltage abnormal protection/ low-voltage cutoff protection, over-thermal protection and throttle signal loss protection, ●

make the ESC more reliable.

High power safety performance: wherever the throttle lever is, the motor will not start immediately.●

Over thermal protection: when ESC temperature is over 100 °C， output power will automatically reduce. When it's lower than 80 output power will ● °C

return to normal.

Cycle menu setting, simple operation. Support setting with program box and transmitter.●

LiPO Cells

50A 70A 90A

120A

A-SW050006 A-SW070006 A-SW090006

A-SW120006 A-SW150006

150A

2-6S2-6S 2-6S 2-6S2-6S

5.5V/5A 5.5V/5A 5.5V/5A 5.5V/5A 5.5V/5A

57*49*18mm

90g

57*49*18mm

101g 102g

57*49*18mm

Boat length＜55cm Boat length＜70cm Boat length＜100cm

Switch BEC Switch BEC Switch BEC Switch BEC Switch BEC

Boat length＜120cm Boat length＜135cm

300A 420A 540A 720A 900A

76*56*25mm 76*56*25mm

155g 169g

Model

Cont. Current

Burst Current

BEC Type

Application

Dimension

(Exclude water pipe)

Weight

BEC Output

Turn on transmitter ,

move throttle trigger

to the full forward

position.

Connect ESC with battery, wait for 2 seconds,

motor emits short “BEEP-BEEP-”twice, move

trigger to neutral position in 5 seconds, the

full throttle position is memorized.

Operation procedure with Pistol Transmitter

Waits for 1second, motor emits

short "BEEP-" few times, sound

times is Lipo battery cells. Then

waits for 1 second, motor emits

1 long “BEEP—”and 1 short

“BEEP-” , the“zero throttle“position

is memorized.

At this time,it's

ready to work now.

At this time,it's

ready to work now.

Waits for 1second, motor emits

short "BEEP-" few times, sound

times is Lipo battery cells. Then

waits for 1 second, motor emits

1 long “BEEP—”and 1 short

“BEEP-” , the“zero throttle“position

is memorized.

Turn on transmitter ,

move throttle stick

to the full forward

position.

Operation procedure with Stick Transmitter

Connect ESC with battery, wait for 2 seconds,

motor emits short “BEEP-BEEP-”twice, move

stick to neutral position in 5 seconds, the

full throttle position is memorized.

Operation procedure with Pistol Transmitter

Operation procedure with Stick Transmitter

Turn on transmitter ,

move throttle trigger

to the nature position.

Connect ESC with battery, wait for 2

seconds,motor emits short "BEEP-" few

times, sound times is Lipo battery cells.

Waits for 1 second, motor emits

1 long “BEEP—”and 1 short “BEEP-”

ESC is ready to work now.

Turn on transmitter ,

move throttle stick

to the nature position.

Connect ESC with battery, wait for 2

seconds,motor emits short "BEEP-" few

times, sound times is Lipo battery cells.

Waits for 1 second, motor emits

1 long “BEEP—”and 1 short “BEEP-”

ESC is ready to work now.

Running Mode

Motor direction adj.

Low voltage

protection

Non-

protection

2.6V 2.8V 3.0V 3.2V 3.4V

CCW

Star t Mode (Punch)

Level 1

Level 2 Level 3 Level 4 Level 5

Timing

0° 3.75° 7.5° 11.25° 15° 18.75° 22.5° 26.25°

1 shor t tone

2 shor t tone

3 shor t tone

4 shor t tone

1 long tone 1 long1 short

1 long2 short 1 long3 short

1 long4 short

Forward

Forward &

Reverse

● ● ●50A 70A 90A

Battery

Receiver

ESC

Motor

*Please ensure all solder joints are insulated with heat shrink where necessary

● ●120A 150A

Battery

Receiver

ESC

Motor

*Please ensure all solder joints are insulated with heat shrink where necessary

Note: We strongly advise the use of battery connections that do not allow reverse polarity , or ESC will be damaged.

Please disconnect the battery and ESC , if not use for a long time.

Summary of content (2 pages)

PAGE 1
User Manual R F ly Mons te r s e r ie s (Boat Brushless ESC) ATTENTION 04 Operation Instruction 1 Set throttle range Advise set throttle range when ﬁrst time to use Flycolor ESC. The feature of Flycolor ESC is that set the best throttle range according to different transmitter, then ESC can get the most smoothly throttle linear through throttle range of transmitter. To make ESC get and memorize throttle output signal. The process only do once, you need do this process again after changing transmitter.
PAGE 2
4. Exit programming There are 2 ways to exit programming mode: 4.1 After hearing the tone “∮1212”, move throttle to the throttle nature position, motor emits special tone “∮765765”, it exits programming mode. 4.2. Turn off power can exit programming mode. saved setting data are the setting before turning off. 2 09 Trouble Shooting Programming with program card It's the easiest way to set with programming card.