User Manual TURNIGY JUMP STARTER T27 Jump Start Socket USB1 Output 5V/2A USB2 Output 5V/3A 9V/2A Switch Type-C 9V/2A Input 1
LED Flashlight USB Output 5V/2A 5V/3A 9V/2A Power Level 2
Operating Instructions: Charging Your T27 You can charge your T27 one of Two ways: 1. Using the supplied 220 Volt main charger. OR 1. Inserting the one end of QC 3.0 car charger into the jack of cigar lighter. 2. Inserting the other end of QC 3.0 car charger into the devices. Charging takes 2 hours using either charging option. If adaptors support QC 3.0 charging, jump starter will be charged at 9V/2A OR 5V/3A, otherwise, jump starter will be charged at 5V/2A.
Starting Your Vehicle: Please ensure that your T27 is no less than 50% charged. If it is below 50%, you may not be able to jumpstart your vehicle. 1. Connect the jumper lead to your T27. 2. Connect the +(red clip) to the + on your car battery. 3. Connect the -(black clip) to the - on your car battery. 4. Turn your key to start your vehicle. 5. Once your vehicle is started, disconnect the alligator clip as soon as possible. Note: 1. After starting your vehicle, Remove the T27 as soon as possible. 2.
Turning On Your T27 Follow 2-step process as below to turn on your T27 jump starter: 1. Press the round power button. 2. Your T27 is now ready to use. Charging Digital Devices via USB 1. You can either use the provided USB Break out lead or your own USB cable suitable for your digital device. 2. Connect either cable to the T27. 3. If using the provided USB Break out lead, Select the correct connection for your device.
How to use the LED Torch 1. Press and hold the round power button for 3 seconds. The LED torch will turn on. 2. Press the round button again to activate the strobe function. 3. Press the round button again to activate the SOS function. Pressing this button for 3 seconds can turn on the LED lighting system Charging Indicator 1. Press the round power button to see the charge status of the T27 LCD Screen. 2. When charging, The LCD Screen will show the specific number range from 0 to 100%. 3.
Trouble Shooting: If the following operations are unable to troubleshoot, please stop using the jump starter and contact with the stores which you bought the jump starter from Trouble Cause Solution The power capacity of the device is shown in 100%, but did not fully charged in charging precoess The battery shown 100% in the LCD Screen of T27 on means stop charging, and this situation means it is semi-state of charge, which is conductive to long-term storage when the device is not in use for long time.
Frequently Asked Questions (FAQ): 1. Q: How long does a full charge take? A: The devices have smart detection, in the case there is no load or charging is finished, the T27 will turn itself off. 2. Q: How long does a full charge take? A: A full charge will take 2 hours using either the 220V or 9V charging option. 3. Q: How many times i can jump start my vehicle? A: This depends on the different displacements and vehicle engine. The T27 item can start a vehicle up to 15 times. 4.
Current return charging protection Voltage stabilization protection Short circuit protection Overload protection Wide temperature ignition Balanced charge Over dischange protection Quality commitment 12 million RMB sum insured Our product’s quality is underwritten by Hobbyking 9
Warranty Card We offer 12-month warrantly service for the product from tha date of purchasing. Warranty conditions: Please show this warranty card and fill in the details to obtain warranty service. We offer 12-month warranty for the product from the date of purchase. Warranty range: Quality problems in the state of normal use can be guaranteed. Damages to the product caused by the operational errors, Warranty can’t be provided. The device is dismantled, no warranty.
