Installation Instructions
Issues Possible Causes Solution
Battery in motor is depleted
Recharge with compatible AC adaptor and check
connection and positioning of solar PV panel
Insufficient charging from Solar
PV Panel
Check connection and orientation of solar PV panel
Wall switch battery is discharged Replace battery
Battery is inserted incorrectly into
wall switch
Check battery polarity
The motor has no response Radio interference / shielding
Ensure wall switch and the antenna on the motor are
positioned away from metal objects
Receiver distance is too far from
wall switch
Move wall switch to a closer position
Power failure Check power supply to motor is connected and active
Incorrect wiring
Check that wiring is connected correctly (refer to motor
installation instructions)
Motor beeps 10 times when in use
Battery voltage is low / PV (solar
panel issue)
Recharge with AC adapter or check connection and
positioning of solar PV panel
Always reserve an individual channel for programming
functions
SYSTEM BEST PRACTICE - Provide an extra 15 channel
remote in your multi-motor projects that provides
individual control for each motor for programming
purposes
Place all other motors into sleep mode (Press “P1”
button (about 6 sec) on the motor head until motor jog
x2 and beep x2).
Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.
Roller
Cellular/Honeycomb
Standard
Cellular/Honeycomb
Skylight
Sheer Banded
Tilt-Only
Horizontal
Narrow
Width
Roman
Cannot program a single motor
(multiple motors respond)
Multiple motors are paired to the
same channel.
Settings Steps
1 Pairing P1 (hold down for 2s) > Stop (hold down for 2s)
2 Switch Rotating Direction Up + Down (hold down for 2s)
3 Setting Upper & Lower Limits
4 Add / Remove Favorite Position P2 > Stop > Stop
5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop
6 Adjust Limits
7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new)
8 Speed Regulation
Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s)
Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)
Acceleration: P2 > Up > Up
Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)
Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)
Deceleration: P2 > Down > Down
AMP
™
Wall Switch
Declarations
Fields of Application
Quick Index
Safety Instructions
Troubleshooting
Button Instructions
Replace/Install Battery
Advanced Setting - Disable Limit Setting
1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the
scope of these instructions may void warranty.
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the
device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
AMPTILT
AMP25B / AMP28B / AMP35B / AMP25BDC AMPCEL
P1 Button
LED light
P1 button
Lithium Battery Switch
Power line
Signal line
P1 Button
Voltage 3V (AAA battery x 2)
Radio Frequency 433.92 MHz Bi-directional
Transmitting Power 10 milliwatt
Operating Temperature 14°F to 122°F (-10°C to 50°C)
RF Modulation FSK
Lock Function Yes
IP Rating IP20
Transmission Distance up to 200m (outdoor)
Specications
a. Press and hold “Stop“ button more than 15s,
WS will show “L” (lock), WS is now in “Lock” mode
and following commands are disabled:
- Change Motor Direction
- Setting the Upper and Lower Limit
- Adjust Limit
- Roller Mode or Sheer Mode
b. Press and hold “Stop“ button more than 15s,
WS will show “U” (unlock) - back to unlock mode,
you can assess all control functions.
a. Gently take out the battery cover.
b. Install 2 x AAA batteries with positive
(+) side facing up.
c. Gently assemble the battery cover back.
a. b.
c.
*This advanced feature is intended to be used after
all shade programming is completed. User Mode
will prevent accidental or unintended changing
of limits.
Please scan QR code to see more
AMP
™
product information
LOWER
CHANNEL
HIGHER
CHANNEL
BATTERY
DOWN
(P2)(P2)
STOP
UP
7#89D0"D'2."D
D=::21D
$*&*9D
D%*%!)*
*%&&'%*
*%&&'%*