Safety Instructions

ManualsBrandsTurnils North America ManualsElectric MotorsDC Tubular Motor & rechargeable battery

Micro-USB Port

Instruction

Attention

-1-

The motor is suitable for motorization of roller blinds

Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.

Important safety instructions to be read before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

-2-

1. Do not expose motor to humid, damp or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna and keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If power cable or connector is damaged, do not use.

6. Ensure correct crown and drive adaptor are used.

7. Ensure power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls shall be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered

operation.

11. Installation and programming to be performed by a qualified professional, use or modification outside

the scope of this instruction may void warranty.

Features

Fields of Application

Specifications

Following data for reference

Working temperature: -10℃ ~ +50℃

Input Voltage: USB 5V 1A / USB 5V 2A

Radio Frequency: 433.925MHz

Maximum Running Time: 6 minutes

Model

Rated Torque

(N.m)

Rated Speed

(rpm)

Rated Power

(W)

- 0.7/34 0.7 34 8

-1.1/28 1.1 28 8

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and

needs to be charged.

During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped

running and needed to be recharged.

Rechargeable Battery

Blinking red:

Low battery alert

Blinking green:

Charging is processing

Solid green:

Battery has

finished charging.

A zoom in on the

charging port

Button Instructions

P1 button

Lithium Battery Switch

LED light

Micro-USB Port

Sheer

Roller

Revolve

Roman shades

Working temperature: -10º C ~ +50º C

Input Voltage: USB 5V 1A / USB 5V 2A Maximum Running Time: 6 minutes

Model

Rated Torque

(N.m)

Rated Speed

(RPM)

Rated Power

(W)

35B-6.0/24 6.0 24 38

Issues Possible Causes Solution

Built in battery is depleted

Recharge with compatible AC adaptor and check

connection and positioning of solar PV panel

Insufﬁcient charging from Solar

PV Panel

Check connection and orientation of solar PV panel

Remote control battery is discharged Replace battery

Battery is inserted incorrectly into

remote control

Check battery polarity

The motor is not responding Radio interference / shielding

Ensure remote control and the antenna on the motor are

positioned away from metal objects

Receiver is far away from Remote

Control

Move remote control to a closer position

Power failure Check power supply to motor is connected and active

Incorrect wiring

Check that wiring is connected correctly (refer to motor

installation instructions)

Motor beeps 10 times when in use

Battery voltage is low / PV (solar

panel issue)

Recharge with AC adapter or check connection and

positioning of solar PV panel

Always reserve an individual channel for programming

functions

SYSTEM BEST PRACTICE - Provide an extra 15 channel

remote in your multi-motor projects that provides

individual control for each motor for programming

purposes

Place all other motors into sleep mode (ref to P1 button

instructions)

Do not dispose of in general waste.

Please recycle batteries and damaged electrical products appropriately.

Roller

Cannot program a single motor

(multiple motors respond)

Multiple motors are paired to the

same channel.

Settings Steps

1 Pairing P1 (hold down for 2s) > Stop (hold down for 2s)

2 Switch Rotating Direction Up + Down (hold down for 2s)

3 Setting Upper & Lower Limits

4 Add / Remove Favorite Position P2 > Stop > Stop

5 Roller Mode & Sheer Mode Switch Up + Down (hold down for 5s) > Stop

6 Adjust Limits

7 Pair / Unpair Additional Emitter P2 (existing) > P2 (existing) > P2 (new)

8 Speed Regulation

Upper Limit: Up (hold down for 2s) > Up + Stop (hold down for 2s)

Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)

Acceleration: P2 > Up > Up

Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)

Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)

Deceleration: P2 > Down > Down

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

ISED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the

device. Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Please scan QR code to see more

AMP

™

product information

× × × ×

Test Motor

Activate Pairing Mode

Sleep Mode

Reverse Direction

Reset To Factory Settings

Approx. 2 sec.

Happening as you press for 2 seconds

Happening as you press for 1 second

Happening as you press for 6 seconds

Happening as you press for 10 seconds

Happening as you press for 14 seconds

when released

Approx. 6 sec.

Approx. 10 sec.

Approx. 14 sec.

Until Shade:

Motor Response:

Until Shade:

Motor Response:

Beep x1

Beep x2

Jog x3

Jog x4

Jog x1

Jog x2

Beep x3

Beep x4

Less than 1 sec.

Press P1

Motor Response:

Wakes & Runs

AMP35B

Declarations

Fields of Application

Quick Index

Attention

Safety Instructions

Troubleshooting

Charging Instructions

Rechargeable Battery

P1 Button Instructions

This motor has a built in Li-ion battery pack with integrated charge management.

Max power input for recharging: 5V 2A.

Before ﬁrst use please charge motor for 6 hours using a 5V charger.

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and needs

to be charged.

During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Blinking red:

Low battery alert

Blinking green:

Charging in process

Solid green:

Battery has ﬁnished

charging

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.

Read all safety instructions before installation.

Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

1. Do not expose motor to humid, damp, or extreme temperature conditions.

2. Do not drill into motor.

3. Do not cut the antenna. Keep it clear from metal objects.

4. Do not allow children to play with this device.

5. If the power cable or connector is damaged, do not use.

6. Ensure the correct crown and drive adaptor are used.

7. Ensure the power cable and aerial is clear and protected from moving parts.

8. Cable routed through walls should be properly isolated.

9. Motor is to be mounted in horizontal position only.

10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.

11. Installation and programming should be performed by a qualiﬁed professional. Use or modiﬁcation outside the

scope of these instructions may void warranty.

Micro-USB Port

Summary of content (2 pages)

PAGE 1
AMP35B Declarations U.S. Radio Frequency FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 2
4. Adjust Limits Button Instructions Button Instructions 4.1 Adjust the Upper Limit button(LED (LEDLight) Light) P1P1 button a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1. LCD Display Micro-USB Port Micro-USB Port Up Stop Down Lower Channel P2 Higher Channel b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.