Installation Instructions
Table Of Contents
- 页 1
- 书签87CF67CE Marianna One Handle Pressure Balanced Shower Set
- 书签68511B26 TUSCANY
- 书签F7D5FB27 Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft damp cloth. Avoid abrasive cleaners, steel wool, and harsh cleaners at these will dull the finish and void the warranty. Vinegar is suggested as an alternative cleaner and is safe for all finishes.
- 书签68C14086 If soldering during the installation of this faucet, remove the seats, cartridges, and washers before adding any heat. The warranty will be voided on these parts if not removed before soldering.
- 书签FF0CC64D Safety glasses should always be worn when cutting or soldering.
- 书签3F80A209 Always cover your drain before installation to prevent losing parts.
- 书签7CA863C9 ∙ Before installation turn off the cold and hot water shut offs. Turn the faucet handle\(s\) on to release the pressure in the system. ∙ Wrap ALL threaded connections with Teflon tape in a clockwise direction.
- 书签6081EAEC Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 书签3C92D2DF Flashlight
- 书签4EF6474E Safety Glasses
- 书签DD9D7A82 Groove Joint Pliers
- 书签5D5A002C For Skus : 673-6113, 673-6114 673-6115
- 页 2
- 书签A5D67A52 Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 书签7B8CBD77 30
- 书签6F691B66 Integral Stop
- 书签B2B84F94 Protective Sleeve
- 书签CA8FFE33 O-rings
- 书签FF9D0BBB O-ring
- 书签9D69D73B Showerhead
- 书签92B0A5B3 Adjuster Seat
- 书签5446DA39 Adjuster
- 书签D26B4495 Sealing Washer
- 书签F79A346D Valve Body
- 书签B82255A8 Cartridge Sleeve
- 书签D9A1E2F4 Sealing Ring
- 书签B245DBF6 Screws
- 书签9F1B2F48 Shower Arm
- 页 3
- 书签9BC84373 Floor
- 书签00F2D03F Tub Rim
- 书签FEECF88A 78''min to finished floor
- 书签0D92B6BC 4-1/2-14NPT
- 书签D69F2FBD 3-11/16" \(94mm\)
- 书签C1CC96DE 1-1/2"-2-3/16" \(38mm-56mm\)
- 书签46D2317E 1/2-14NPT
- 书签6FC23523 Recommended 74” \(1880mm\) Minimum From Floor To Showerhead, Or Greater As Desired
- 书签23D60627 Φ6-7/8" \(175mm\)
- 书签A03DE151 5-1/2" \(140mm\)
- 书签20D3EC61 8-11/16" \(220mm\)
- 书签512AD1B7 10-1/2" \(267mm\)
- 书签D952A05F 4-9/16" \(116mm\)
- 书签D70898AB Steps 1-2
- 书签952BD45F 1. Note the minimum/maximum installation dimensions between the shower arm \(#22\) and handle \(#1\). Also note, if this is a thin wall mounting, the hole for the valve body \(#13\) must be 5-1/2". Diagram accounts for a 17" standard tub.
- 书签C64919F3 2. Verify the valve body \(#13\) is properly oriented. The word "UP" on the valve body \(#13\) should be toward the riser; "DOWN" should be pointed toward the tub spout outlet; the flat surface of the plaster guard should be flush with the finished wall. Secure the valve body to the support cross board for stability. Note: If this is not a thin wall mounting, the plaster guard \(#8\) may be removed from the valve body \(#13\).
- 书签B20AD794 13
- 书签5FFB4B66 8
- 书签CE33257A Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 页 4
- 书签60FA5EDE Installation Instructions
- 书签84F24679 5. Slide the shower arm flange \(#21\) onto the longer end of the shower arm \(#22\). Wrap the threads of the longer end of the shower arm \(#22\) with Teflon tape and install to the shower drop. Wrap the threads in Teflon tape. Verify the rubber washer \(#27\) is in place between the showerhead \(#23\) and the shower arm \(#22\). Install the showerhead \(#23\) onto the shower arm \(#22\).
- 书签F8D504FE 4. Turn on the hot and cold water shut offs and check for leaks. If a leak occurs, refer to steps 3 or 4. Turn on the faucet and let the water run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water. Note: Turn on both the hot and cold water shut offs before turning the faucet on. Not turning on both will cause your cartridge to become pressure locked. If this occurs, see the troubleshooting guide.
- 书签312361A6 4
- 书签3BAC4EAE Steps 3-5
- 书签2B0539D2 Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 书签B85A8EC1 3. Apply Teflon tape to all pipe threads. Install an elbow at one end of the pipe. Install the other end to the shower diverter \(top hole\) of the valve body \(#13\). Secure the shower elbow to a 2x4 bracing.
- 页 5
- 书签F74C3C70 Installation Instructions
- 书签0F020712 6. Remove the protective sleeve \(#28\) from the plaster guard \(#8\) by twisting the protective sleeve \(#28\) counterclockwise. Note: Verify the handle adapter at the tip of the cartridge \(#11\) is securely attached to the cartridge \(#11\). If loose, locate the set screw \(bottom side of adapter\) and tighten the set screw with the provided Allen wrench \(#29\). If the set screw is not in the cartridge \(#11\), check the packaging or contact customer service.
- 书签78E09445 7. Temperature Limiting Device: Remove the trim cap \(#9\) and lock nut \(#10\). By default, the temperature limiting device is set to the highest temperature setting \(A\). In order to reduce the temperature, remove the temperature limiting device \(the red cap\) and turn the device clockwise to the desired temperature \(position B or C\). Reinstall the lock nut \(#10\) and trim cap \(#9\).
- 书签494F1388 Steps 6-8
- 书签3653D696 Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 书签72114896 8. Verify the escutcheon gasket \(#7\) and sealing ring \(#6\) are attached to the escutcheon \(#5\). Slide the escutcheon \(#5\) over the cartridge sleeve \(#12\) and secure it with screws \(#4\) and O-ring \(#24\). Note: Do not remove the customer service tag with the model number and phone number. This information will be needed when calling the customer service department.
- 书签68D5BDF2 11
- 书签FF7A3A45 8
- 书签C4B63F21 11
- 书签18EE66C7 Handle Adapter
- 书签AB62F7A8 Set Screw
- 页 6
- 书签408126AF Installation Instructions
- 书签4A714C2D Steps 9-10
- 书签63A8553C 10. Turn on the water and check for leaks. If a leak occurs from \(#22\) or \(#23\) in the diagram, repeat step 5.
- 书签5FD91AD0 Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 书签79C8BB88 9. Slide the handle \(#1\) onto the cartridge \(#11\). Then use the set screw \(#2\) to secure the handle \(#1\). Insert the handle button \(#3\). See the diagram for a visual.
- 页 7
- 书签5F8D8545 Troubleshooting
- 书签AEB42F64 7
- 书签E838494E The lock nut \(#10\) has come loose or the O-ring on the cartridge \(#11\) is dirty or misaligned.
- 书签39283487 The rubber valve seat at the base of the pressure balance cartridge \(#11\) is dirty or broken.
- 书签1C5CC05B The cartridge \(#11\) is dirty, damaged, or pressure locked.
- 书签BC12267D Turn off the water supplies. Turn on the handle \(#1\) to release the pressure, then close the handle \(#1\). Remove the handle button \(#3\), set screw \(#2\), handle \(#1\) and trim cap \(#9\). If the lock nut \(#10\) is loose tighten it. If the lock nut \(#10\) is tight, remove the lock nut \(#10\) and cartridge \(#11\). Verify the O-ring is clean and in proper alignment on the cartridge \(#11\). If the O-ring is dirty rinse it in warm water. Reinstall the O-ring onto the cartridge \(#11\). Reinstall the cartridge \(#11\), lock nut \(#10\), trim cap \(#9\), and handle \(#1\), set screw \(#2\) and handle button \(#3\). Turn the water supplies on.
- 书签DCDC9ACE Turn off the water supplies. Turn on the handle \(#1\) to release the pressure, then close the handle \(#1\). Remove the handle button \(#3\), set screw \(2\), handle \(#1\) and trim cap \(#9\), lock nut \(#10\), and the cartridge \(#11\). Verify the rubber valve seat is damage free, clean, and in proper alignment on the cartridge \(#11\). If the rubber valve seat is damaged replace the cartridge \(#11\). If the rubber valve seat is dirty rinse in warm water. Reinstall the rubber valve seat onto the cartridge \(#11\). Reinstall the cartridge \(#11\), lock nut \(#10\), trim cap \(#9\), handle \(#1\), set screw \(#2\) and handle button \(#3\). Turn the water supplies on.
- 书签C1D796BB Turn off the water supplies. Turn on the handle \(#1\) to release the pressure, then close the handle \(#1\). Remove the handle button \(#3\), set screw \(#2\), handle \(#1\), trim cap \(#9\), lock nut \(#10\), and cartridge \(#11\). Inspect the cartridge \(#11\) for dirt and damage. Replace the cartridge \(#11\) if damaged. Shake the cartridge \(#11\) and verify the pressure balance spool \(located at the bottom of the cartridge \(#11\)\) is moving freely \(clicks when shaken\). If the spool is not moving, tap it on your hand until it begins to click. If the cartridge \(#11\) is dirty, soak it in warm white vinegar for 4 hours. Every 30 minutes, while the cartridge \(#11\) is submerged in the vinegar, rotate the stem on and off 10 times. Reinstall the cartridge \(#11\), lock nut \(#10\), trim cap \(#9\), handle \(#1\), set screw \(#2\), and handle button \(#3\). Turn the water supplies on.
- 书签3DA2521F Leaks underneath the handle \(#1\).
- 书签2C26E1BC The water will not shut off completely.
- 书签74150FB7 The water temperature cannot be adjusted or there is no hot or cold water.
- 书签48D3D09A Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.
- 书签37EBC55A If the installation instructions have been followed carefully and the faucet still does not work properly, take these corrective steps. CAUTION: Faucets are under pressure. For safety, before preforming maintenance on the faucet always turn off the water at the water supply valve and turn on the handle\(s\) to release the pressure.
- 页 8
- 书签952A49D3 The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation. Our responsibility under this warranty is limited only to the replacement of parts and no other costs. Should a malfunction occur within the time covered by this warranty, replacement parts may be obtained from Customer Service Department 1-800-626-3525 or email warranty@cmiproduct.com. The manufacturer will, at its discretion, provide replacement parts for installation by consumer for any parts that prove defective under normal usage and care with new or equivalent parts.
- 书签42B9160D Revised on 07/07/2021
- 书签D517DE3E 8
- 书签304D6769 Have a question? DON’T GO BACK TO THE STORE. WE CAN HELP. Just call 1-800-626-3525,8 a.m. to 5 p.m. EST Monday-Friday. Or send an email to Help@cmiproduct.com.