Installation Instructions
Table Of Contents
- 页 1
- 书签E82FF916 TUSCANY
- 书签19B11AD2 Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft damp cloth. Avoid abrasive cleaners, steel wool, and harsh cleaners at these will dull the finish and void the warranty. Vinegar is suggested as an alternative cleaner and is safe for all finishes.
- 书签D71FDD7F If soldering during the installation of this faucet, remove the seats, cartridges, and washers before adding any heat. The warranty will be voided on these parts if not removed before soldering.
- 书签B2213688 Safety glasses should always be worn when cutting or soldering.
- 书签C99E719E Always cover your drain before installation to prevent losing parts.
- 书签C259A8A1 Before installation turn off the cold and hot water shut offs. Turn the faucet handle\(s\) on to release the pressure in the system. Before installing the water supply lines to the new faucet, bleed the water supply lines into a bucket for one minute to remove any debris that could clog the faucet. Wrap ALL threaded connections with Teflon tape in a clockwise direction. When installing the new faucet, turn the connectors finger tight, then use an adjustable wrench to tighten the connectors. Connections that are too tight will reduce the integrity of your system.
- 书签BE228284 Flashlight
- 书签DCF7B19C Single Handle Vessel Lavatory Faucet
- 书签1CFE259E For Models : 673-7060, 673-7061 673-7062
- 页 2
- 页 3
- 书签FFE487B6 1. Shut off the water supplies before installation. Remove the current faucet. Clean and dry the surface the new faucet will be installed on. Note: This faucet fits 3 cm/1-3/16" countertops.
- 书签DA3F125C Note: Do not remove the customer service tag with the model number and phone number as this will be helpful if you need assistance in the future.
- 书签01575FE0 3. Apply Teflon tape to the threads of the hot and cold water supply tubes on the waterway \(#14\) in a clockwise direction.
- 书签D0D5F4DC 14
- 书签A3725DB1 4. Verify the O-ring \(#18\) is in place. Apply silicone sealant beneath the base \(#17\). Install the faucet through the single faucet hole. From underneath, reassemble the gasket assembly \(#21\) and the lock nut \(#22\). Hand tighten the lock nut \(#22\) lining up one of the screws \(#23\) with the groove in the gasket assembly \(#21\). Do not over tighten. Use a Phillips screwdriver to tighten the screws \(#23\) on the lock nut \(#22\). Note: Assemble in the order listed with the rubber washer \(#39\) first. See the diagram for a visual. Hint: Have someone hold the body \(#16\) in place while tightening.
- 书签76EA11D9 18
- 书签7C309A25 39
- 书签F242EB17 40
- 书签94E3CBD7 16
- 页 4
- 书签557C7953 Installation Instructions
- 书签E64C9121 Steps 5-9
- 书签50CA9ABC 9. Overflow Hole Instructions: Note: Skip this step if installing the drain into a sink without an overflow hole. Unscrew the cover \(#28\) counterclockwise by hand. Unscrew the stopper core \(#29\) counterclockwise using a pair of pliers if needed. Screw the stopper core \(#29\) into the stopper housing \(with overflow hole\) \(#31\). Screw the cover \(#28\) onto the stopper core \(#29\).
- 书签A20DFE0E 30
- 书签B322D283 31
- 书签9FCCDA28 7. Remove the nut \(#38\), outlet pipe \(#37\), O-ring \(#36\), lock nut \(#35\), wearing ring \(#34\), and bottom rubber washer \(#33\) from the drain assembly. Note: Before installation, verify there is no damage to the push down pop-up drain. If there is damage, please call customer service for a replacement. Do NOT install damaged parts.
- 书签04F7B249 30
- 书签25E68163 32
- 书签B410B186 33
- 书签9371BDD4 34
- 书签74749AE7 35
- 书签41F94595 36
- 书签4147AA6C 37
- 书签77DBE9F6 38
- 书签3F356D13 8. Remove the old drain assembly. Clean the surface to remove the old adhesive and dirt before installing the new drain. Dry the area thoroughly.
- 书签A986B8BC 28
- 书签62B633F8 29
- 书签5857D050 4
- 书签3A144DED Teflon
- 页 5
- 书签316D9712 Installation Instructions
- 书签9212F534 13. Open the hot and cold shut offs and check for leaks.
- 书签D29FEF6B 15. Turn on both the hot and cold water and let it run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water.
- 书签0BA1355D 14. Close the drain and fill the sink with water. Check for leaks. If water is leaking from the drain, refer to step 11 or 12.
- 书签8B9A6872 11. From underneath the sink, slide the bottom rubber washer \(#33\) and wearing ring \(#34\) onto the stopper housing \(#30 or #31\), then screw on the lock nut \(#35\) hand tight. Do not over tighten. See the diagram for a visual.
- 书签86EC0C21 36
- 书签1E39562C 38
- 书签56677194 37
- 书签1CCBFA78 12. Slide the nut \(#38\) over the outlet pipe \(#37\) and insert the O-ring \(#36\) onto the outlet pipe \(#37\). Screw the nut \(#38\) onto the stopper housing \(#30 or #31\) hand tight. Do not over tighten. Note: The outlet pipe \(#37\) connects to the p-trap drain. Refer to the installation instructions for the p-trap for more information on how to connect the outlet pipe \(#37\) to the p-trap drain.
- 书签CEA4835F 30 or 31
- 书签814963DA 33
- 书签B61D0506 34
- 书签0AF915FE 35
- 书签1B496E16 30 or 31
- 书签0B706AB0 30 or 31
- 书签B5DDBA5C 32
- 书签D5F84C88 10. Place a ring of silicone sealant around the top rubber washer \(#32\) on the stopper housing \(#30 or #31\) or the drain opening of the sink. Insert the stopper housing \(#30 or #31\) into the drain hole from the top.
- 书签D7317B27 If a leak occurs, refer to step 5 or 6.
- 书签E62A1B14 Steps 10-15
- 页 6
- 书签FD0CE500 Revised on 10/30/2020
- 书签2671DA70 Turn off the water supplies. Turn on the handle \(#3\) to release the pressure, then close the handle \(#3\). Remove the handle \(#3\) and trim cap \(#4\). If the lock nut \(#7\) is loose tighten it. If the lock nut \(#7\) is tight, remove the lock nut \(#7\) and cartridge \(#9\). Verify the O-ring is clean and in proper alignment on the cartridge \(#9\). If the O-ring is dirty rinse in warm water. Reinstall the O-ring onto the cartridge \(#9\). Reinstall the cartridge \(#9\), lock nut \(#7\), trim cap \(#4\) and handle \(#3\). Turn the water supplies back on.
- 书签34D519AE The lock nut \(#7\) has come loose or the O-ring on the cartridge \(#9\) is dirty or misaligned.
- 书签061D8097 Dirty or damaged cartridge \(#9\).
- 书签B1F1BFF3 Turn off the water supplies. Turn on the handle \(#3\) to release the pressure, then close the handle \(#3\). Remove the handle \(#3\), trim cap \(#4\), lock nut \(#7\), and cartridge \(#9\). Check the ceramic disk for dirt and damage. Replace the cartridge \(#9\) if damaged. If the cartridge \(#9\) is dirty, soak it in warm white vinegar for 4 hours. Every 30 minutes, while the cartridge \(#9\) is completely submerged, turn the stem on and off 10 times. Reinstall the cartridge \(#9\), lock nut \(#7\), trim cap \(#4\), and handle \(#3\). Turn the water supplies back on.
- 书签F193E35F Troubleshooting
- 书签AC3E9CD3 Leaks underneath the handle \(#3\).
- 书签35F51768 The water will not shut off completely.
- 书签7A454857 Screen filter \(#27\) is dirty.
- 书签A5147E51 Faucet has an inconsistent water flow.
- 书签69E3DFD0 Turn off the water supplies. Turn on the handle \(#3\) to release the pressure, then close the handle \(#3\). Disconnect the supply lines from the waterway \(#14\) and remove screen filters \(#27\). Keeping the raised face of the screen filter \(#27\) downward, clean the screen filter \(#27\) gently with a soft bristled brush. Reinstall the screen filters \(#27\) and supply lines. Turn the water supplies on. Check for leaks. \(Refer to step 6 for instructions on reinstalling the supply lines.\)
- 书签2296AE8B The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation. Our responsibility under this warranty is limited only to the replacement of parts and no other costs. Should a malfunction occur within the time covered by this warranty, replacement parts may be obtained from Customer Service Department 1-800-626-3525 or email warranty@cmiproduct.com. The manufacturer will, at its discretion, provide replacement parts for installation by consumer for any parts that prove defective under normal usage and care with new or equivalent parts.