Tools Adjustable Wrench(2) « Teflon Tape Groove Joint Puller « Screwdriver Silicone Sealant Maintenance Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft, damp cloth. Av old abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and cold your warranty. Safety Tips « If you use soldering for the Installation of the faucet, the seats, cartridges and washers well have to be removed before using flame.
Parts Diagram / List Part Name 1 Handle 2 Wearing Ring 3 Handle Body 4 | Orin 5 Handle Connector 6 Screw 7 Handle Base 8 Lock Nut 9 | o-ING 10 | Cartridge {Hot) 11 | under body 12 | Allen Wrench 13 | Washer 14 | Metal Washer 15 | Lock Nut 16 | Screw 17 | Knob 18 | Body 1% | Aerator 20 | Aerator Color 21 Screw 22 | spout Base 23 | Screw 24 | Gasket 25 | O-ring 26 | Inlet Pipe 27 | Washer 28 | Metal Washer 29 | Nut 30 | Washer 31 | Connector 32 | O-ring 33 | Nut 34 | Tee 35 | Cartridge [Cold) 36 | Aerator Wre
Preparation/Assembly 1. Shut off water supplies before installation. Remove current faucet, clean and dry the sink surface the new faucet will be installed on. 2. Unscrew nut (#29) and remove washer metal washer (#28) from the faucet. Note: Do not remove the customer service tag with the model number and phone number as this will be helpful if you need assistance in the 27 future. This faucet fits counter tops. 3.
Installation Instructions Step 5-8 . Apply Teflon tape to the threads of the under body (#11) in a clockwise direction. . Apply silicone sealant beneath the handle base (#7) and insert the under body (#11) through the far left hole (hot water side). Repeat this step for the far right hole (cold water side). See the diagram for a visual. . From underneath the sink, reassemble the washer metal washer (#14) and the lock nut Hand tighten the lock nut Do not over tighten.
Installation Instructions Hot Wat Cold Wat 9. Attach water supply hoses to the faucet. Use two Supply Tube Supply Tube wrenches (as shown) to keep from twisting the supply tube off of the faucet when tightening the nut. 10. Apply Teflon tape on to the threads of the faucet water shut offs In a clockwise direction. Tighten the water supply hoses onto the water supply shut offs.
Installation Instructions 14. Verify the threads for the ball nut (#49) are pointed straight back to the pop-up rod (#41) location. Slide the washer and lock nut (#46) onto the drain body and up against the bottom of the sink. Tighten the washer and lock nut (#46) firmly against the base to ensure a tight seal. 15. Remove the ball nut (#49) and the sealer Insert the stopper (#43) into the pop-up body Align the hole in the stopper (#43) with the guide rod opening. (See the diagram for a visual).
Installation Instructions 18. Use the aerator wrench (#36) to remove the aerator assembly Open the hot and cold shut offs and check for leaks. If leak occurs, refer to step 9 or 10. ~FIT 19. Close the drain and fill the sink with water. Check &se for leaks. If water Is leaking from the drain, refer to step tighten the drain lock nut 20. Turn on both the hot and cold water and let It run for one minute.
Troubleshooting If you've followed the Instructions carefully and your faucet still does not work properly, take these corrective steps. Problem Cause Action The cartridge (#10 or #35) has Tighten of replace the cartridge Leaks underneath the handle. come loose. (#10 or #38), Remove the handle assembly and cartridge {#10 or Check the ceramic disk for dif and dosage. {the cartridge {#10 or #35) s dirty. soak it in warm white vinegar for 4 hoers.
