Installation Instructions

ManualsBrandsTuscany ManualsBathAudrey Single Handle Tub and Shower Faucet in Chocolate Bronze and Brushed Nickel

Table Of Contents

Summary of content (8 pages)

PAGE 1
Tools « Adjustable Wrench (2) « Teflon Tape Groove Joint Slier + Phillips Screwdriver Silicone Sealant Audrey Single Handle Pressure Balanced Tub/Shower Set Maintenance Your new faucet is designed for years of trouble-free performance. Keep it looking new by cleaning it periodically with a soft, damp cloth. Avoid abrasive cleaners, steel wool and harsh chemicals as these will dull the finish and cold your warranty.
PAGE 2
Parts Diagram / List Part Name Shower Arm Flange Shower Arm Shower Head Screws Protective Sleeve Trim Cap Lack Nut Cartridge Cartridge Housing Valve Body O-ring Sealing Washer Stop Valve Core Stop Valve Spring Adjuster Seat Set Screw Handle Escutcheon Gasket Sealing Ring Escutcheon Handle Button O-rings Screws Allen Wrench Teflon Tape Adjuster O-rings Spout Knob O-ring | Screw 2116 2223 24 25 O-ring O-ring Plastic Core Ring O-ring Core Cover Pulling Core Sealing Plate Washer Washer Spout Assembly: Plaster G
PAGE 3
Preparation/Assembly 1. Note the minimum/maximum installation dimensions between the shower arm handle (#17) and spout Also note, if this is a thin wall mounting, the hole for the valve body (#10) must be in diameter. 3 (161mm) = (38mm-56mm) Ln-sE 611167 (169mm) JTITTTITITTTIT7 Floor ng 2. If this is not a thin wall mounting, the plaster guard (#43) may be removed from the valve body Note: Secure the valve body (#10) to the support cross board for stability.
PAGE 4
Installation Instructions 3. Shower Only: Plug the tub spout diverted (bottom hole) of the valve body using the washer shower only Tub Only (#46) and end cap Skip step 5 and 8. Tub Only: Plug the shower diverted (top hole) of the valve body using the washer (#46) and end cap Skip step 4 and 7. Note: For a watertight connection, wrap Teflon tape (#25) around all threads in a clockwise $e direction. i= 4. Apply Teflon tape (#25) to all pipe threads. Install an elbow at one end of the pipe.
PAGE 5
Installation Instructions 6. Turn on the hot and cold water shut offs and check for leaks. If leaks occur, refer to steps 4 or 5. Turn on the faucet and let the water run for one minute. This will help clear any debris that may have come loose during installation and prevent the system from becoming clogged. Turn off the water. Note: Turn on both the hot and cold water shut offs before turning the faucet on. Not turning on both will cause your cartridge (#8) to become pressure locked.
PAGE 6
Installation Instructions Temperature Limiting Device: Remove the trim cap (#6) and lock nut By default, the temperature limiting device is set to the highest temperature setting (A). In order to reduce the temperature, remove the temperature limiting device (the red cap) and turn the device clockwise to the desired temperature (position B or C).
PAGE 7
Troubleshooting If you've followed the Instructions carefully and your faucet still does not work properly, take these corrective steps. Problem Cause Action Leaks underneath the handle The lock nut (#7) has come loose or the O-ring on the cartridge (#8) is dirty or misaligned. Turn off the water supplies. Turn on the handle (#17} to release the pressure, then close the handle Remove the handle button set screw handle {#17} and| trim cap If the lock nut (#7) is loose tighten it.
PAGE 8
Lifetime Limited Warranty The manufacturer warrants that the parts and assemblies of this product will be free from defects in material and workmanship under normal household use for as long as it is owned by the original consumer purchaser. This warranty covers the original purchaser with original receipt only and does not include business, commercial or industrial use of this product. This warranty shall not apply to goods which have been subject to accidents, negligence or improper installation.