Installation Instructions

ManualsBrandsTuscany ManualsDual-Mount Kitchen SinksMorey All-in-One Dual Mount 19" Stainless Steel Single Bowl Bar/Prep Sink

Note: The sink provided is considered a universal mount sink - it can either be

installed as an under mount with the counter top overhang or a traditional top mount.

For top mount installations, please follow .

For under mount installations, please follow .

- -

- top-mount sinks installation

- under-mount sinks installation

The warranty will be voided if these installation instructions are not followed.

Remember, it is your responsibility to follow all local plumbing and building codes.

CAUTION: Risk of personal injury. Metal surfaces can be sharp and can cause severe cuts.

Please use gloves and handle the sink with care.

BEFORE INSTALLING THE SINK, INSPECT IT FOR DAMAGE. DO NOT

INSTALL A DAMAGED UNIT.

— —

Dual-mount Sinks Installation Instructions

Stainless Steel

RECOMMENDED TOOLS

For safety and ease of installation, factory recommends the use of the helpful tools above.

Drill and Drill Bit

Long Shank Flat Screwdriver

Silicone Caulk and Caulk Gun

Pencil

Saber Saw

Flashlight

Teflon Tape

Safety Glasses

Gloves

Adjustable Wrench

5 6

1 2

8 9 10 11

Plumber's Putty/Silicone Sealant

— —

Top-mount Sinks Installation

Step 2 (Out With The Old)

Here's how to remove the old sink:

A. Shut off the water supply valves.

B. Disconnect the water supply fittings.

C. Disconnect the drain fittings.

D. From the underside of the sink, w ,

loosen and remove the frame clamps or rim fasteners.

E. Lift the entire sink out of the counter top.

ith your flashlight and long screwdriver

Step 3 (Check Your Dimensions)

Check the countertop cut-out opening by placing the sink in the opening to be

sure it is sized properly. The sink rim must be set uniformly on the countertop,

ensure the corners of the sink sit properly. If the sink does not fit, enlarge the

cut-out opening with a saber saw.

Step 4 ( )Attach Faucet, Drain Fittings and Accessories

If you are installing a new faucet and/or drain fitting, garbage disposal or other

accessory, follow the directions provided with these products. If you are re-

installing the fittings you had on the old sink, first clean off all old putty or

silicone before installing, then mount it on the new sink using putty or silicone

caulk under the disposer flange.(See sink strainer installation instructions

below.) Using flexible supply lines, measure from the shut off to the bottom of

the countertop, add at least 4" to the measurement to allow for movement.

Attach your supply lines to the faucet using teflon tape on all threaded water

connections at this time.

Step 1

THIS STEP ONLY FOR NEW COUNTER INSTALLATION.

IF YOU HAVE AN OLD COUNTER TOP ALREADY CUT, PLEASE GO TO STEP 2.

( ,

)

B. It is impor tant that your cut-out be EXACT. First, drill a 3/8" dia. hole for the

saber saw blade on the inside edge of the cut-out. Cut sink opening, using the

cut-out line as your guide. Brace up the cut-out por tion as you complete cutting

to avoid splintering the edge of hole. Sand edges smooth.

C. Go to step 3 .

For laminate counter top only other materials should refer to the counter top

manufacture's recommendations.

Locate template, put masking tape over the area where your sink cut-out will

be, this helps avoid splintering of the laminate when you are cutting, trace

completely around edge of cut-out template.

Step 2

Step 3

Length

idt

Step 4

Plumbers Putty

COUNTERTOP

Cut On Inside

Step 1

Trace Completely Around

Edge Of Cut-out Template

COUNTERTOP

Sink Strainer Installation Instructions

● Place strainer in sink opening making cer tain that sufficient G

( )

(A) Locknut

(B) Rubber Washer

(E) Tailpiece Washer

(D) Slip Nut

(F) Strainer Flange

Sink

(G) Plumbers' Putty

Step 7 ( )Engage and Tighten Fasteners

Inser t the sink into the counter top.

A U

(If the cut-out is undersize, please go back to

step 3 and do not force the sink.)

Position the fasteners claw end under top edge (See diagram (1) for example).

Locate the fastener in the position as shown in diagram (2).

CAUTION: Improper tightening of channel fasteners could result in improper

nstallation or cause damage to sink.

Tightening Sequence is as follows:

. With channel fasteners equally spaced, and with one at each end of channel

bar, hand tighten channel fasteners, star ting at center and working toward

sides.

. Re-check sink position on counter top.

. Tighten all channel fasteners an additional quar ter turn with a flat head

screwdriver. IMORTANT – DO NOT OVERTIGHTEN.

Step 8 ( )Connect Faucet Supplies and Drain Fittings

Connect the drain trap fittings, connect the faucet supply fittings using teflon tape

and turn on the water supply. Check for possible leaks at these locations: Supply

lines to faucet, and Supply lines to shut-off valves (or, lower connections). Next

fill the sink bowl with water and check for possible leaks around the drain

flange(s). If there is a leak you will see water dripping onto the bottom of the

cabinet. Release the water from the sink and check for possible leaks at the drain

connection. Tighten any joint that is leaking.

Step 6 ( )Assemble and Inser t Sink Fasteners

Step 5

Apply compound completely around

all edges of sink opening. Stay approximately 1/4" from cut-out.

Use only a 1/8" to 1/4" bead of silicone. More will make the sink

difficult to seal to the countertop.

a small bead of silicone caulk

Assemble the screws into the channel fasteners as shown . (Note: Screws are

designed to inser t into the channel fasteners with backward threading, so that in

mounting, they will turn the counter-clockwise direction.) Locate the fasteners in

the position as shown . Hand tighten each fastener onto the channel so that the

clamp “teeth” point is the same direction as the channel.To install channel

fasteners in channel bar : Slide channel fasteners into channel bar from either

open end and/or slots in channel.

U (1)

(2)

U U

Step 8

Step 5

1/8" To 1/4"

Bead of Silicone

Speed

Screw

Backward

Thread

Clamp

U Channel

Turn "speed screw"

clockwise to hand tighten.

Step 6

(1) (2)

COUNTERTOP

Sink

Drop Into Cut

Out With Clamp

Parallel To

Channel

Rotate

Clamp

90°To

Channel

Turn Clockwise

To Tighten

Screw Driver

Sink

COUNTERTOP

(1)

(2)

Step 7

Plumbers' Putty is used between the bottom of the trainer

Flange and the top of the sink to seal properly.

(F)S

Inser t tailpiece through lip Nut and then assemble to the bottom of the

strainer outlet.

(D)S

● From underneath, place ubber Washer first, then riction (B)R (C)F

Washer. Screw threaded locknut onto strainer.

● Thread on ocknut, hold strainer firmly in place. Tighten securely .

● Place ailpiece Washer inside of tailpiece with flat side of washer facing up.

(A)L

(E)T

Summary of content (6 pages)

PAGE 1
Top-mount Sinks Installation Step 1 Dual-mount Sinks Installation Instructions THIS STEP ONLY FOR NEW COUNTER INSTALLATION. IF YOU HAVE AN OLD COUNTER TOP ALREADY CUT, PLEASE GO TO STEP 2. ( For laminate counter top only, other materials should refer to the counter top manufacture's recommendations. ) A. Locate template, put masking tape over the area where your sink cut-out will be, this helps avoid splintering of the laminate when you are cutting, trace completely around edge of cut-out template. B.
PAGE 2
Top-mount Sinks Installation Step 1 Dual-mount Sinks Installation Instructions THIS STEP ONLY FOR NEW COUNTER INSTALLATION. IF YOU HAVE AN OLD COUNTER TOP ALREADY CUT, PLEASE GO TO STEP 2. ( For laminate counter top only, other materials should refer to the counter top manufacture's recommendations. ) A. Locate template, put masking tape over the area where your sink cut-out will be, this helps avoid splintering of the laminate when you are cutting, trace completely around edge of cut-out template. B.
PAGE 3
Top-mount Sinks Installation Step 1 Dual-mount Sinks Installation Instructions THIS STEP ONLY FOR NEW COUNTER INSTALLATION. IF YOU HAVE AN OLD COUNTER TOP ALREADY CUT, PLEASE GO TO STEP 2. ( For laminate counter top only, other materials should refer to the counter top manufacture's recommendations. ) A. Locate template, put masking tape over the area where your sink cut-out will be, this helps avoid splintering of the laminate when you are cutting, trace completely around edge of cut-out template. B.
PAGE 4
Under-mount Sinks Installation Step 4 (Install the Sink) Undermount sinks can be installed with two different reveals - Reveal and Flush. Please select your reveal prior to installation. (See diagram) Reveal - The counter top edge sits approximately 1/4" back from the edge of the sink, exposing the sink rim. Reveal Clean the bottom of the counter top and the top flange. Then apply a bead of silicone adhesive sealant to the top edge of the bowl flange and position the bowl in the counter top.
PAGE 5
Under-mount Sinks Installation Step 4 (Install the Sink) Undermount sinks can be installed with two different reveals - Reveal, Flush Deciding on your preferred Look must be done prior to installation.(See diagram) Reveal - The counter top edge sits approximately 1/4" back from the edge of the sink, exposing the sink rim. Reveal Clean the bottom of the counter top and the top flange. Then apply a bead of silicone adhesive sealant to the top edge of the bowl flange and position the bowl in the counter top.
PAGE 6
Under-mount Sinks Installation Step 4 (Install the Sink) Undermount sinks can be installed with two different reveals - Reveal and Flush. Deciding on your look must be done prior to installation.(See diagram) Reveal - The counter top edge sits approximately 1/4" back from the edge of the sink, exposing the sink rim. Reveal Clean the bottom of the counter top and the top flange. Then apply a bead of silicone adhesive sealant to the top edge of the bowl flange and position the bowl in the counter top.