MR6K-48X Mid-Rise Scissor Lift 6,000 lbs. Capacity (1,500 lbs.
CONTENT SAFETY INFORMATION · Note, Caution and Warning · Important Information · Safety Instructions TECHNICAL INFORMATION · Product Description · Specifications BEFORE USING · Site Selection · Surface Condition · Operating Condition INSTALLATION INSTRUCTIONS · · · · · Required Tools Unloading Lift Un-banding Lift Lift Assembly Starting Up / Testing OPERATION INSTRUCTIONS · · · · Vehicle Positioning, Lifting & Lowering Inspection, Maintenance & Cleaning Trouble-Shooting Guide Power Unit Priming Proced
SAFETY INFORMATION Note, Caution and Warning This document uses the following notations: Note, Caution and Warning – to alert you to special instructions, tips, or hazards for a given procedure. Please familiarize yourself with the notation explanations described below. Indicates important information that requires special attention, such as a procedure for a specific vehicle, or tips on operating the equipment.
Safety Instructions 1. Do not raise a vehicle on the lift until the installation is completed as described in this manual. 2. Technicians should be trained to use and care for the lift by familiarizing themselves with the manual, including Note, Caution and Warning information. The lift should never be operated by an untrained person. 3. Always position the pads properly out of the way before pulling the vehicle into or out of the service bay. Failure to do so could damage the vehicle and/or the lift. 4.
TECHNICAL INFORMATION Product Description The MR6K-48X is a portable 6,000 lb. hydraulic mid-rise scissor frame contact lift, equipped with twin hydraulic cylinders & extended radius arms and contact pads for maximum strength and stability. The lift raises straight up without forward or aft movement and comes standard with portable dolly / power cart for wheel service, brake work, inspections & detailing all with the ease of mobility.
7” 54” 70.8” BEFORE USING Site Selection The Lift is designed for indoor use only. Application in a room with explosion hazard is not permitted. Placing the lift in a wet place, such as car wash bay, is prohibited. Ensure to check the desired location for possible obstructions such as a low ceiling, overhead lines, adequate working area, access ways and exits. Make sure to allow a minimum space of 12 to 14 feet in front and behind the Lift to accommodate all vehicles.
INSTALLATION INSTRUCTIONS You will need common hand tools that most homeowners have, like a hammer, screwdrivers and pliers, but in addition, you may need some tools that are not common. Each installation is somewhat different and depends on how much room you have to work around the lift. Required Tools 1. 2. 3. 4. 5. 6. 7.
STEP 2: Mounting Power Unit to Dolly A. Remove power unit from the carton. B. Use provided nuts & bolts to attach power unit to dolly’s mount plate (Fig. 3). Fig. 3 Fig. 4 STEP 3: Hydraulic Hose Connection & Filling Reservoir Tank A. Connect hydraulic hose to the pump’s output port (Fig. 4). B. Remove the black fill cap on reservoir tank and fill with 6 quarts of Non-Detergent / NonFoaming Hydraulic Oil - SAE-10, AW 32 or equivalent. Ensure not to fill past the MAX Fill Line on the reservoir tank.
Starting Up / Testing A. Push the ‘start button’ on the motor pump to prime the hydraulic oil into the cylinders on the lift. The lift will rise up with lock latch passing over the lock ladder (Fig. 6). B. Release the start button to stop the lift from rising. Press down on the ‘lowering valve lever’ and the lift will lower down and automatically engage the next lower lock height (Fig. 6). Fig. 6 C. Push the ‘start button’ just 2-3 seconds to slightly raise the frame.
OPERATION INSTRUCTIONS Never operate the Lift if the Safety Lock Assembly is not working properly. 1. Plug the Power Cord of the Lift into a properly grounded, 3-hole, electrical receptacle or extension cord. 2. Squeeze and release the Lock Release Hand Lever several times and while doing so, observe that the Safety Lock Assembly operates properly in response to the Hand Lever. Release pressure on the Hand Lever to release Lock. 3.
5. Position the Arms outward and position the Saddle Pads to contact the vehicle lifting points. 6. Do not lift the vehicle if you cannot establish secure and level lifting points. Do not use sub-standard shims or other devices in place of approved and recommended Saddle Pad Adapters. Never use the Lift without the Saddle Pads in place for each Arm. 7.
Trouble-Shooting Guide 1. Motor Does Not Run: A. Breaker or fuse blown............Call electrician B. Faulty wiring connections...... Call electrician C. Defective start button.............Call electrician D. Defective capacitor................ Call electrician 2. Motor Runs but Will Not Raise: A. Oil level too low......................Oil level should be at the MAX Fill Line with lift fully lowered. B. Check for proper clearance for the release valve’s stem seat. C.
IMPORTANT POWER UNIT PRIMING PROCEDURE THE PROBLEM: Power unit runs fine but will not pump any fluid. Step 1 – Locate the check valve. It is the plug to the left of the lowering valve. Step 2 – Using a Hex wrench and shop towel – with shop towel in place to catch fluid – loosen the check valve plug by approximately 2-½ turns and allow fluid to bleed off. Step 3 – Push the START button for one second, then release for three seconds. Repeat these steps until unit starts pumping fluid.
EXPLODED DRAWING 14 MR6K-48X Dec 2017-A
PARTS LIST ITEM Tux P/N M REF P/N 1BX MR6K-48X-001-BX XF01-04000-000 2B DESCRIPTION QTY Top Platform 1 MR6K-48X-002B Pin 3mm x 40mm 2 3B MR6K-48X-003B Pin 3mm x 40mm 2 4B MR6K-48X-004B Hose fitting from T - HYD 1 5B MR6K-48X-005B Cylinder Hose 2 6B MR6K-48X-006B Hose Fitting to Cylinder 2 7B PU-110V-S-K Power Unit 115VAC 1 8B MR6K-48X-008B Bolt M8 x 25 8 9B MR6K-48X-009B Nut M8 x 25 4 10B MR6K-48X-010B Lock Release Cable 1 11B MR6K-48X-011B Dolly Handle 1 12
36B-1C MR6K-48X-036B-1C Lock Pin 1 36B-2C MR6K-48X-036B-2C QJYJ3-02-14/6 Lock Spring 1 36B-3C MR6K-48X-036B-3C QJYJ3-02-14/3 Lock Latch 1 36B-4C MR6K-48X-036B-4C QJYJ3-02-14/1 Lock Bar 1 36B-5C MR6K-48X-036B-5C QJYJ3-02-14/5 Lock Cam 1 36B-9C MR6K-48X-036B-9C QJYJ3-02-14 Lock Tube 1 36B-10C MR6K-48X-036B-10C Washer D8 2 36B-11C MR6K-48X-036B-11C Bolt M8 x 16 2 36B-12C MR6K-48X-036B-12C T-Valve Hyd 1 37BX MR6K-48X-037BX Pin 4mm x 50mm 2 38B MR6K-48X-038B QJYJ3-0
LIMITED WARRANTY Structural Warranty: The following parts and structural components carry a five-year warranty: Columns Legs Tracks Arms Carriages Cross Rails Uprights Overhead Beam Top Rail Beam Swivel Pins Limited One-Year Warranty: Tuxedo Distributors, LLC (Tuxedo) offers a limited one-year warranty to the original purchaser of Lifts and Wheel Service equipment in the United States and Canada.
