SJ-35 Sliding Bridge Jack 3,500 lbs.
TABLE OF CONTENTS Specifications.......................................................................................................... Description & Features……………………………………………………………......... Installation Instructions........................................................................................... Safety Instructions.................................................................................................. Operating Instructions.............................................................
DESCRIPTION This SJ-35 jack is a hand pump operated, scissor style sliding bridge jack, designed to be mounted on the four-post lift’s runway edges between runways. It is capable of lifting the wheels off runways to provide ‘wheels free’ service for brake, suspension, tire repairs and maintenance. FEATURES A. Lifting capacity of the sliding jack is 3500 lbs. (1600 kg). B. The sliding body assembly arms are adjustable for an inside runway width of 30" (762 mm) minimum to a 45.7” (1162 mm) maximum. (Fig.
INSTALLATION INSTRUCTIONS 1. Carefully remove sliding jack from its package. 2. Pump jack to top by the hand pump. Check that the hydraulic oil quantity is enough and hose is properly connected. 3. Lower the jack completely down by moving the lock release lever to the right, while turning the hydraulic release valve knob counter-clockwise. 4. Slide out the slider body assembly extensions on both sides to match the width between the runways. 5. Put the jack on the edges of the runways (Fig.
OPERATING INSTRUCTIONS WARNING!!! To avoid personal injury and/or property damage, permit only trained personnel to operate jack. After reviewing these instructions, get familiar with jack controls by running the jack through a few cycles before loading vehicle on jack. Observe and avoid any pinch point areas of the linkage mechanism. 1. Before loading a vehicle onto lift, ensure jack(s) are fully lowered. Make sure the adapters are in their most inbound and lowest position.
MAINTENANCE INSTRUCTIONS WARNING! If you are not completely familiar with automotive lift maintenance procedure, please contact your distributor for instructions before any practice. TO AVOID PERSONAL INJURY, permit only qualified personnel to perform maintenance on this equipment. Daily: • Inspect sliding jack adapters for damage or excessive wear. • Inspect hydraulic system for leaks. • Inspect for loose bolts, broken/damaged components. • Inspect linkages for damage, wear and tear.
TROUBLE SHOOTING TROUBLE Sliding Jack will not raise after contacting load CAUSE 1. Jack loaded beyond capacity. 2. External fluid leak at pump, hose or cylinder. 3. Internal leakage. 4. Release mechanism damaged or parts missing. 5. Pump low on fluid. 6. Pump malfunctioning. Sliding Jack will not raise to full height. Jack drifts down - will not hold. Jack lowers slow or not at all. 1. Pump low on fluid. 1.Release mechanism damaged or parts missing REMEDY 1. Use Jack only to rated capacity. 2.
EXPLODED VIEW 8 SJ-35 May 2017
PARTS LIST ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 25.1 26 27 28 29 30 30.1 31 32 33 34 Tux P/N SJ-35-001 SJ-35-002 SJ-35-003 SJ-35-004 SJ-35-005 SJ-35-006 SJ-35-007 SJ-35-008 SJ-35-009 SJ-35-010 SJ-35-011 SJ-35-012 SJ-35-013 SJ-35-014 SJ-35-015 SJ-35-016 SJ-35-017 SJ-35-018 SJ-35-019 SJ-35-020 SJ-35-021 SJ-35-022 SJ-35-023 SJ-35-024 SJ-35-025 SJ-35-025.1 SJ-35-026 SJ-35-027 SJ-35-028 SJ-35-029 SJ-35-030 SJ-35-030.
35 36 37 37.1 37.2 37.3 37.4 37.5 37.6 37.7 37.8 37.9 38 39 40 41 42 47 48 SJ-35-035 SJ-35-036 SJ-35-037 SJ-35-037.1 SJ-35-037.2 SJ-35-037.3 SJ-35-037.4 SJ-35-037.5 SJ-35-037.6 SJ-35-037.7 SJ-35-037.8 SJ-35-037.
SJ-35 May 2017
