30i TRANSarc welding Inverter A-11731 Operating Manual Revision: AA Operating Features: Issue Date: January 10, 2013 Manual No.
WE APPRECIATE YOUR BUSINESS! Congratulations on your new Cigweld product. We are proud to have you as our customer and will strive to provide you with the best service and reliability in the industry. This product is backed by our extensive warranty and world-wide service network. To locate your nearest distributor or service provider call +1300 654 674, or visit us on the web at www.cigweld.com.
! WARNINGS Read and understand this entire Manual and your employer’s safety practices before installing, operating, or servicing the equipment. While the information contained in this Manual represents the Manufacturer’s best judgement, the Manufacturer assumes no liability for its use.
TABLE OF CONTENTS SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS...................................... 1-1 1.01 1.02 1.03 Arc Welding Hazards........................................................................................ 1-1 Principal Safety Standards............................................................................... 1-5 Declaration of Conformity................................................................................ 1-6 SECTION 2: INTRODUCTION .......................
TABLE OF CONTENTS SECTION 6: KEY SPARE PARTS.................................................................................... 6-1 6.01 6.02 6.03 Power Source.................................................................................................. 6-1 TIG Torch W4013804 (where supplied)........................................................... 6-2 Stick Electrode Holder with Trigger Switch 646761(where supplied)............... 6-3 APPENDIX: TRANSARC 130i CIRCUIT DIAGRAM........................
TRANSARC 130i SECTION 1: ARC WELDING SAFETY INSTRUCTIONS AND WARNINGS ! WARNING PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS KEEP AWAY UNTIL CONSULTING YOUR DOCTOR. DO NOT LOSE THESE INSTRUCTIONS. READ OPERATING/INSTRUCTION MANUAL BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.
TRANSARC 130i 2. Wear approved safety glasses. Side shields recommended. WARNING ARC RAYS can burn eyes and skin; NOISE can damage hearing. Arc rays from the welding process produce intense heat and strong ultraviolet rays that can burn eyes and skin. Noise from some processes can damage hearing. 1. Use a Welding Helmet or Welding Faceshield fitted with a proper shade of filter (see ANSI Z49.1 and AS 1674 listed in Safety Standards) to protect your face and eyes when welding or watching. 3.
TRANSARC 130i 3. Remove all flammables within 35 ft (10.7 m) of the welding arc. If this is not possible, tightly cover them with approved covers. WARNING 4. Be alert that welding sparks and hot materials from welding can easily go through small cracks and openings to adjacent areas. FUMES AND GASES can be hazardous to your health. Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. 5. Watch for fire, and keep a fire extinguisher nearby. 6.
TRANSARC 130i 5. Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and associated parts in good condition. 6. Turn face away from valve outlet when opening cylinder valve. 7. Keep protective cap in place over valve except when cylinder is in use or connected for use. 8. Read and follow instructions on compressed gas cylinders, associated equipment, and CGA publication P-1 listed in Safety Standards.
TRANSARC 130i 1.02 Principal Safety Standards Safety in Welding and Cutting, ANSI Standard Z49.1, from American Welding Society, 550 N.W. LeJeune Rd., Miami, FL 33126. Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing Office, Washington, D.C. 20402. Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held Hazardous Substances, American Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W.
TRANSARC 130i 1.03 Declaration of Conformity Manufacturer: CIGWELD Address: 71 Gower St, Preston Victoria 3072 Australia Description of equipment: Welding Equipment (GTAW, MMAW) including, but not limited to CIGWELD Transarc 130i Welding Inverter and associated accessories. Serial numbers are unique with each individual piece of equipment and details description, parts used to manufacture a unit and date of manufacture.
TRANSARC 130i SECTION 2: INTRODUCTION 2.01 How To Use This Manual 2.02 Equipment Identification To ensure safe operation, read the entire manual, including the chapter on safety instructions and warnings. The unit’s identification number (specification or part number), model, and serial number usually appear on a nameplate attached to the control panel. In some cases, the nameplate may be attached to the rear panel.
TRANSARC 130i 2.04 Symbol Chart Note that only some of these symbols will appear on your model. On Single Phase Wire Feed Function Off Three Phase Wire Feed Towards Workpiece With Output Voltage Off.
TRANSARC 130i 2.05 Description 2.07 Transporting Methods The Cigweld Transarc 130i is a self contained single phase multi process welding inverter that is capable of performing MMAW (Stick) and GTAW (Lift TIG) welding processes. The unit is equipped with an integrated voltage reduction device (VRD applicable in stick mode only), digital amperage/voltage meter, and a host of other features in order to fully satisfy the broad operating needs of the modern welding professional.
TRANSARC 130i 2.09 Duty Cycle The rated duty cycle of a Welding Power Source, is a statement of the time it may be operated at its rated welding current output without exceeding the temperature limits of the insulation of the component parts. To explain the 10 minute duty cycle period the following example is used. Suppose a Welding Power Source is designed to operate at a 25% duty cycle, 130 amperes at 25.2 volts. This means that it has been designed and built to provide the rated amperage (130A) for 2.
TRANSARC 130i 2.10 Specifications Description Transarc 130i W1007130 Plant Part No Plant Part No (Mine Spec) W1007131 Power Source Part No (Mine Spec) Power Source Dimensions Power Source Mass Cooling Welder Type Australian Standard Number of Phases Nominal Supply Voltage W1007129 H306mmxW121mmxD376mm 7 KG Fan Cooled Multi Process Inverter Power Source AS 60974.1-2006 / IEC 60974.
TRANSARC 130i NOTE 4 Minimum Generator Recommendation at the Maximum Output Duty Cycle. Due to large variations in performance and specifications of different brands and types of generators, Cigweld cannot guarantee full welding output power or duty cycle on every brand or type of generator. Some small generators incorporate low cost circuit breakers on their outputs. These circuit breakers usually will have a small reset button, and will trip much faster than a switchboard type circuit breaker.
TRANSARC 130i SECTION 3: INSTALLATION, OPERATION AND SETUP 3.01 Environment These units are designed for use in environments with increased hazard of electric shock as outlined in AS 60974.1 and AS 1674.2. A. Examples of environments with increased hazard of electric shock are: 1. In locations in which freedom of movement is restricted, so that the operator is forced to perform the work in a cramped (kneeling, sitting or lying) position with physical contact with conductive parts. 2.
TRANSARC 130i C. Methods of Reducing Electromagnetic Emissions action may be as simple as earthing the welding circuit, see NOTE below. In other cases it could involve constructing an electromagnetic screen enclosing the Welding Power Source and the work, complete with associated input filters. In all cases, electromagnetic disturbances shall be reduced to the point where they are no longer troublesome. 1.
TRANSARC 130i bonding the workpiece to earth may reduce emissions in some, but not all instances. Care should be taken to prevent the earthing of the workpiece increasing the risk of injury to users, or damage to other electrical equipment.
TRANSARC 130i Fail to safe operation This welding power source is also protected by a special protection feature called “Fail to Safe Operation” which is available in all welding modes. The output of the power source will be disabled and the fault indicator will illuminate if the “Fail to Safe” protection has operated.. The “Fail to Safe” protection will not automatically reset. The mains power switch must be turned off to reset the power source.
TRANSARC 130i A-11734 Figure 3-3: Programming Mode STICK Programming Mode Programming Parameter Control Panel Display Hot Start This parameter operates in STICK mode to improve the start characteristics for stick electrodes HOT START current is on top of the BASE current. e.g. HOT START current = 130 amps when BASE (WELD) = 100 amps & HOT START = 30 amps Range is 0 to 70A. Factory default is 20A. Note that maximum weld current is 170A. Base Current This parameter sets the STICK weld current.
TRANSARC 130i Programming Parameter Control Panel Display Arc Force Arc Force is effective when in STICK mode only. Arc Force control provides an adjustable amount of Arc Force (or "dig") control. This feature can be particularly beneficial in providing the operator the ability to compensate for variability in joint fit-up in certain situations with particular electrodes. In general increasing the Arc Force control toward 100% (maximum Arc Force) allows greater penetration control to be achieved.
TRANSARC 130i Base Current This parameter sets the TIG welding current. Range is 5 to 130A. Factory default is 120A. Down Slope This parameter operates in TIG mode only and is used to set the time for the weld current to ramp down to the crater current. This control is used to eliminate the crater that can form at the completion of a weld. Range is 0.0 to 25.0 seconds. Factory default is 3.0 seconds. Crater Current This parameter operates in TIG mode only.
TRANSARC 130i Post Flow This parameter operates in TIG mode only and is used to adjust the post gas flow time once the arc has extinguished. This control is used to dramatically reduce oxidation of the tungsten electrode. Range is 0.0 to 30.0 seconds. Factory default is 5.0 seconds. 5. Positive Welding Output Terminal The positive welding terminal is used to connect the welding output of the power source to the electrode holder lead or work lead.
TRANSARC 130i Socket Pin Function 1 Not connected 2 Trigger Switch Input 3 Trigger Switch Input 4 Not connected 5 5k ohm (maximum) connection to 5k ohm remote control potentiometer. 6 Zero ohm (minimum) connection to 5k ohm remote control potentiometer. 7 Wiper arm connection to 5k ohm remote control Amps GTAW (TIG) mode potentiometer. 8 Not connected. Table 3-1 8.
TRANSARC 130i A-11725 STICK Dead Man Switch Mode A special trigger mode called “Dead Man Switch” mode is available on the 130i when welding with STICK electrodes. In this mode, there will be no output voltage at all from the Power Source until the trigger is pressed. This provides the greatest level of safety for the operator, and is mandatory on some work sites. While the Dead Man Switch function greatly increases operator safety, standard welding safety procedures should still be followed.
TRANSARC 130i A-11745 There will be 0V on the Power Source welding terminals and both VRD lights will be off. In both 2T and 4T modes, if the stick electrode is not touched to the work piece within three seconds, the welding output will be inhibited. Release the trigger to reset, and press the trigger again to reactivate the VRD. Note that if the Dead Man Switch function is disabled, 2T and 4T are not available in STICK mode.
TRANSARC 130i 10. Process Selection Control The process selection control is used to select the desired welding mode. Two modes are available, GTAW (Lift TIG) and MMAW (Stick) modes. Refer to section 3.08 for GTAW (TIG) set-up details or section 3.09 for MMAW (stick) set-up details. Note that when the unit is powered on the mode selection control will automatically default to LIFT TIG mode.
TRANSARC 130i 3.07 Shielding Gas Regulator Operating Instructions (where supplied) ! WARNING This equipment is designed for use with welding grade (Inert) shielding gases only. Shielding Gas Regulator Safety This regulator is designed to reduce and control high pressure gas from a cylinder or pipeline to the working pressure required for the equipment using it. If the equipment is improperly used, hazardous conditions are created that may cause accidents.
TRANSARC 130i Installation 1. Remove cylinder valve plastic dust seal. Clean the cylinder valve outlet of impurities that may clog orifices and damage seats before connecting the regulator. Crack the valve (open then close) momentarily, pointing the outlet away from people and sources of ignition. Wipe with a clean lint free cloth. 2. Match regulator to cylinder. Before connecting, check that the regulator label and cylinder marking agree and that the regulator inlet and cylinder outlet match.
TRANSARC 130i Shutdown Close cylinder valve whenever the regulator is not in use. To shut down for extended periods (more than 30 minutes). 1. Close cylinder or upstream valve tightly. 2. Open downstream equipment valves to drain the lines. Bleed gas into a well ventilated area and away from any ignition source. 3. After gas is drained completely, disengage adjusting screw and close downstream equipment valves. 4.
TRANSARC 130i Figure 3-7: Setup for TIG Welding 3.09 Foot Control Part No.
TRANSARC 130i Pin Description 1 Not Used 2 Trigger Switch 3 Trigger Switch 4 Not Used 5 Potentiometer Maximum 6 Potentiometer Minimum 7 Potentiometer Wiper 8 Not Used Table 3-2 Description The CIGWELD Foot Control is a foot operated switch and potentiometer which starts and stops the welding process and controls welding current through operation of the foot pedal. Refer to list below for compatible Cigweld power sources.
TRANSARC 130i 3.10 Setup for Manual Arc (MMAW) Welding A. Connect the Electrode Holder lead to the positive welding terminal (+). If in doubt, consult the electrode manufacturer. Welding current flows from the Power Source via heavy duty bayonet type terminals. It is essential, however, that the male plug is inserted and turned securely to achieve a sound electrical connection. B. Connect the work lead to the negative welding terminal (-). If in doubt, consult the electrode manufacturer.
TRANSARC 130i SECTION 4: BASIC WELDING GUIDE 4.01 Stick (MMAW) Basic Welding Technique Size of Electrode The electrode size is determined by the thickness of metals being joined and can also be governed by the type of welding machine available. Small welding machines will only provide sufficient current (amperage) to run the smaller size electrodes. For thin sections, it is necessary to use smaller electrodes otherwise the arc may burn holes through the job.
TRANSARC 130i Welding Position The electrodes dealt with in this publication can be used in most positions, i.e. they are suitable for welding in flat, horizontal, vertical and overhead positions. Numerous applications call for welds to be made in positions intermediate between these. Some of the common types of welds are shown in Figures 4-1 through 4-8.
TRANSARC 130i Art# A-07693 Figure 4-7: Overhead Position, Butt Weld Art # A-07694 Figure 4-8: Overhead Position, Fillet Weld Joint Preparations In many cases, it will be possible to weld steel sections without any special preparation. For heavier sections and for repair work on castings, etc., it will be necessary to cut or grind an angle between the pieces being joined to ensure proper penetration of the weld metal and to produce sound joints.
TRANSARC 130i Arc Welding Technique - A Word to Beginners For those who have not yet done any welding, the simplest way to commence is to run beads on a piece of scrap plate. Use mild steel plate about 6.0mm thick and a 3.2mm electrode. Clean any paint, loose scale or grease off the plate and set it firmly on the work bench so that welding can be carried out in the downhand position. Make sure that the work clamp is making good electrical contact with the work, either directly or through the work table.
TRANSARC 130i If the travel is too fast, the bead will be narrow and strung out and may even be broken up into individual globules. If the travel is too slow, the weld metal piles up and the bead will be too large. Making Welded Joints Having attained some skill in the handling of an electrode, you will be ready to go on to make up welded joints. A. Butt Welds Set up two plates with their edges parallel, as shown in Figure 4-11, allowing 1.6mm to 2.4mm gap between them and tack weld at both ends.
TRANSARC 130i to prevent slag from running ahead of the weld. Refer to Figure 4-13. Do not attempt to build up much larger than 6.4mm width with a 3.2mm electrode, otherwise the weld metal tends to sag towards the base, and undercut forms on the vertical leg. Multi-runs can be made as shown in Figure 4-14. Weaving in HV fillet welds is undesirable.
TRANSARC 130i Art # A-07702 Figure 4-16: Multi Run Vertical Fillet Weld Art # A-07703 Figure 4-17: Examples of Vertical Fillet Welds 2. Vertical Down The Ferrocraft 21 electrode makes welding in this position particularly easy. Use a 3.2mm electrode at 100 amps. The tip of the electrode is held in light contact with the work and the speed of downward travel is regulated so that the tip of the electrode just keeps ahead of the slag. The electrode should point upwards at an angle of about 45º. 3.
TRANSARC 130i Distortion Distortion in some degree is present in all forms of welding. In many cases it is so small that it is barely perceptible, but in other cases allowance has to be made before welding commences for the distortion that will subsequently occur. The study of distortion is so complex that only a brief outline can be attempted hear. The Cause of Distortion Distortion is caused by: A.
TRANSARC 130i B. Distribution of Stresses Distortion may be reduced by selecting a welding sequence which will distribute the stresses suitably so that they tend to cancel each other out. See Figures 4-20 through 4-23 for various weld sequences. Choice of a suitable weld sequence is probably the most effective method of overcoming distortion, although an unsuitable sequence may exaggerate it. Simultaneous welding of both sides of a joint by two welders is often successful in eliminating distortion. C.
TRANSARC 130i 3 2 1 Art # A-07710_AB Block Sequence. The spaces between the welds are filled in when the welds are cool.
TRANSARC 130i Electrode Selection Chart CIGWELD Electrode Selection Chart Pack Part No. Description Diameter Satincraft 13 2.5mm 2.5mm 3.2mm 3.2mm 1kg 2.5kg 1kg 2.5kg 322135 612182 322136 612183 2.0mm 2.0mm 2.5mm 2.5mm 3.2mm 3.2mm 2.0mm 2.0mm 2.5mm 2.5mm 2.5mm 3.2mm 3.2mm 3.2mm 1kg 2.5kg 1kg 2.5kg 1kg 2.5kg 1 kg 2.5 kg 1 kg 2.5 kg 5 kg 1 kg 2.5 kg 5 kg 322128 612231 322129 612232 322138 612233 WEG1020 WEG2520 WEG1025 WEG2525 WEG5025 WEG1032 WEG2532 WEG5032 Ferrocraft 16 Twincoat 2.5mm 3.
TRANSARC 130i 4.02 Stick (MMAW) Welding Troubleshooting FAULT 1 Welding current varying CAUSE REMEDY ARC FORCE is set at a value that causes the welding current to vary excessively with the arc length. A Welding current too low 2 A gap is left by failure of the weld B Electrode too large for metal to fill the joint. root of the weld. C Insufficient gap.
TRANSARC 130i 5 Portions of the A Small electrodes used on A Use larger electrodes and preheat the plate. weld run do not heavy cold plate. fuse to the surface B Welding current is too low. B Increase welding current. of the metal or C Adjust angle so the welding arc is directed more edge of the joint. C Wrong electrode angle. into the base metal. D Travel speed of electrode is too high. D Reduce travel speed of electrode. E Scale or dirt on joint surface. E Clean surface before welding.
TRANSARC 130i 4.03 TIG (GTAW) Basic Welding Technique Gas Tungsten Arc Welding (GTAW) or TIG (Tungsten Inert Gas) as it is commonly referred to, is a welding process in which fusion is produced by an electric arc that is established between a single tungsten (nonconsumable) electrode and the work piece. Shielding is obtained from a welding grade shielding gas or welding grade shielding gas mixture which is generally Argon based.
TRANSARC 130i Tungsten Electrode Types Electrode Type (Ground Finish) Welding Application Features Colour Code Thoriated 2% DC welding of mild steel, stainless steel and copper Excellent arc starting, Long life, High current carrying capacity Red Zirconated 1% High quality AC welding of aluminium, magnesium and their alloys. Self cleaning, Long life, Maintains balled end, High current carrying capacity.
TRANSARC 130i TIG Welding is generally regarded as a specialised process that requires operator competency. While many of the principles outlined in the previous Arc Welding section are applicable a comprehensive outline of the TIG Welding process is outside the scope of this Operating Manual. For further information please refer to www. cigweld.com.au or contact Cigweld. 4.04 TIG (GTAW) Welding Problems FAULT CAUSE REMEDY 1 Excessive bead build up or poor penetration or poor fusion at edges of weld.
TRANSARC 130i 7 Dirty weld pool A Electrode contaminated A Clean the electrode by grinding off the by contact with work contaminates. piece or filler rod material. B Work piece surface has B Clean surface. foreign material on it. C Gas contaminated with C Check gas lines for cuts and loose fitting air. or change gas cylinder. 8 Poor weld finish 9 Arc start is not smooth. Inadequate shielding gas. Increase gas flow or check gas line for gas flow problems.
TRANSARC 130i BASIC WELDING GUIDE 4-18 Manual 0-5283
TRANSARC 130i SECTION 5: POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS 5.01 Power Source Problems FAULT CAUSE REMEDY 1 Mains supply voltage A Power source is not in the coris ON, Amps Display is rect mode of operation. illuminated however unit will not commence weld- B Faulty torch trigger. ing when the torch trigger switch is depressed. 2 Fault Indicator is illuminated and unit will not commence welding when the torch trigger switch is depressed. 3 Welding arc cannot be established.
TRANSARC 130i 10 Fault light is on, and E-1 is shown on the Amps display. A Fail to Safe protection has operated in STICK mode- VRD fault. A Reset mains power, if fault does not clear then have an accredited CIGWELD service provider repair unit. B Fail to safe protection has operated in TIG mode- Inverter fault. B Reset mains power, if fault does not clear then have an accredited CIGWELD service provider repair unit.
TRANSARC 130i Minimum Insulation Resistance (MΩ) Components to be Tested Input circuit (including any connected control circuits) to welding circuit (including any connected control circuits) 5 All circuits to exposed conductive parts 2.
TRANSARC 130i F. Accessories Accessory equipment, including output leads, electrode holders, torches, wire feeders and the like shall be inspected at least monthly by a competent person to ensure that the equipment is in a safe and serviceable condition. All unsafe accessories shall not be used. G. Repairs If any parts are damaged for any reason, it is recommended that replacement be performed by an accredited Cigweld Service Provider. Power Source Calibration A.
TRANSARC 130i 5.03 Cleaning the Welding Power Source ! WARNING There are dangerous voltage and power levels present inside this product. Do not attempt to open or repair unless you are a qualified electrical tradesperson. Disconnect the Welding Power Source from the Mains Supply Voltage before disassembling. To clean the Welding Power Source, open the enclosure and use a vacuum cleaner to remove any accumulated dirt, metal filings, slag and loose material. 5.
TRANSARC 130i POWER SOURCE PROBLEMS AND ROUTINE SERVICE REQUIREMENTS 5-6 Manual 0-5283
TRANSARC 130i SECTION 6: KEY SPARE PARTS 6.
TRANSARC 130i TRANSARC 130i POWER SOURCE SPARE PARTS ITEM 1 2 3 4 5 PART NUMBER W7005808 W7005807 W7005809 W7005810 W7003019 6 W7005811 7 8 9 10 11 12 13 14 15 W7005812 W7005814 W7004908 W7005605 W7005813 W7004913 W7003004 W7003010 705152 DESCRIPTION PCB Power PCB Control 130i PCB Front Panel (Display) 130i Knob Control Dinse Socket 25mm2 Control Socket 8 pin (Note that 8 pin control plug is part number UOA706900) Shielding Gas Outlet 5/8-18 CT Output Shielding Gas Solenoid Valve Assembly Shielding Ga
TRANSARC 130i 6.03 Stick Electrode Holder with Trigger Switch 646762(where supplied) Stick Electrode Holder with Trigger Switch 646762 spare parts diagram A-11710 Figure 6-3 ELECTRODE HOLDER SPARE PARTS ITEM PART NO.
TRANSARC 130i KEY SPARE PARTS 6-4 Manual 0-5283
TRANSARC 130i APPENDIX: TRANSARC 130i CIRCUIT DIAGRAM A N E SW1 24VDC FAN SOLENOID CY1 EMC FILTER FJ TH1 J1 R2 POSITIVE INPUT RECTIFIER L4 V7 DY1 4R 50W DY2 DY V8 IN SOURCE NEGATIVE DRIVE MAIN CONTROL BOARD R39 R63 C20 C21 C17 C19 IFB T1 T4 CT1 T1 R100, 102 T14 T17 R101, 103 8 PIN REMOTE TORCH TRIGGER DISPLAY BOARD C100 C101 COUT1 COUT2 CT2 HALL EFFECT L1 POSITIVE NEGATIVE WELDING TERMINALS APPENDIX A-1 QF OT1 GUN OT2 Manual 0-5283 WELD NEGATIVE WEL
TRANSRC 130i APPENDIX A-2 Manual 0-5283
CIGWELD - LIMITED WARRANTY TERMS LIMITED WARRANTY: CIGWELD Pty Ltd, A Victor Technologies Company, hereafter, “CIGWELD” warrants to customers of its authorized distributors hereafter “Purchaser” that its products will be free of defects in workmanship or material.
TERMS OF WARRANTY – January 2013 1. The Trade Practices Act 1974 (Commonwealth) and similar State Territory legislation relating to the supply of goods and services, protects consumers’ interests by ensuring that consumers are entitled in certain situations to the benefit of various conditions, warranties, guarantees, rights and remedies (including warranties as to merchantability and fitness for purpose) associated with the supply of goods and services.
WARRANTY SCHEDULE – January 2013 These warranty periods relate to the warranty conditions in clause 2. All warranty periods are from date of sale from the Accredited Distributor of the equipment. Notwithstanding the foregoing, in no event shall the warranty period extend more than the time stated plus one year from the date CIGWELD delivered the product to the Accredited Distributor. Unless otherwise stated the warranty period includes parts and labour.
Australia Terms of Warranty – 2013 Effective 1st January 2012, all warranties against defects (also known as a manufacturer’s warranty) supplied with goods or services must comply with the new Australian consumer law regulations (2010). This Warranty Statement should be read in conjunction with the Warranty Schedule contained in the operating instructions of the product.
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION CIGWELD, Australia 71 Gower Street Preston, Victoria Australia, 3072 Telephone: 61-3-9474-7400 Fax: 61-3-9474-7391 Email: enquiries@cigweld.com.au Victor Technologies USA 2800 Airport Road Denton, Tx 76207 USA Telephone: (940) 566-2000 800-426-1888 Fax: 800-535-0557 Email: sales@thermalarc.
Asia Pacific Regional Headquarters 71 Gower Street Preston, Victoria, Australia, 3072 Telephone: +61 3 9474 7400 +61 3 9474 7391 FAX: Email: enquiries@cigweld.com.au www.cigweld.com.
