Owner's manual

Manual 0-4828 Rev BA 8-37 TORCH DATA for Ultra-Cut
Aluminum
Flow Rates
150A
N₂ (SLPM / SCFH) H₂O (GPH / LPH)
Preow
24 / 51 8 / 30
N₂ Plasma / H₂O Shield
Culow
16 / 35 8 / 30
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1016 21-1048 21-1278 21-1092 21-1041 21-1081 21-1020
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
ga (in) inch (psi) Ball (psi) Ball (psi)* (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
- 3/16 0.188 70 60 90 8 55 130 0.100 0.2 0.250 0.200 0.2 0.350 150 0.2 0.107
- 1/4 0.250 70 60 90 8 55 133 0.120 0.2 0.250 0.200 0.2 0.350 120 0.2 0.108
- 3/8 0.375 70 60 90 8 55 140 0.120 0.2 0.250 0.200 0.2 0.350 100 0.2 0.116
- 1/2 0.500 70 60 90 8 55 152 0.200 0.3 0.250 0.200 0.2 0.350 75 0.3 0.126
- 5/8 0.625 70 60 90 8 55 155 0.200 0.7 0.250 0.200 0.2 0.350 50 0.4 0.142
- 3/4 0.750 70 60 90 8 55 165 0.250 1.0 0.250 0.200 0.2 0.350 35 0.5 0.141
- 7/8 0.875 70 60 90 8 55 172 0.275 1.7 0.250 0.200 0.2 0.350 28 0.8 0.148
- 1 1.000 70 60 90 8 55 178 0.300 2.5 0.250 0.200 0.2 0.350 20 1.0 0.155
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
(mm) (Bar) Ball (Bar) Ball (Bar)* (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
5 4.8 60 6.2 8 3.8 130 2.6 0.2 6.4 5.1 0.2 8.9 3700 0.2 2.7
6 4.8 60 6.2 8 3.8 132 2.9 0.2 6.4 5.1 0.2 8.9 3220 0.2 2.7
8 4.8 60 6.2 8 3.8 137 3.0 0.2 6.4 5.1 0.2 8.9 2780 0.2 2.8
10 4.8 60 6.2 8 3.8 142 3.4 0.2 6.4 5.1 0.2 8.9 2450 0.2 3.0
12 4.8 60 6.2 8 3.8 149 4.6 0.3 6.4 5.1 0.2 8.9 2050 0.3 3.1
15 4.8 60 6.2 8 3.8 154 5.1 0.6 6.4 5.1 0.2 8.9 1450 0.4 3.5
20 4.8 60 6.2 8 3.8 167 6.5 1.2 6.4 5.1 0.2 8.9 830 0.6 3.6
25 4.8 60 6.2 8 3.8 177 7.5 2.4 6.4 5.1 0.2 8.9 530 1.0 3.9
Marking
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height
THC and CNC
Delay
Control
Delay
Travel
Speed
Marking quality
degrades as
thickness
decreases.
17A Arc Current
Plasma (N₂) Shield (N₂)
Burn-through may
happen for thicknesses
< 1/16” (0.063”) /
1.6 mm.
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) /
(mm/ min)
20 / 1.4 60
60 /
4.1
75
80 /
5.5
130 0.120 / 3.0 0.120 / 3.0 0 0.4
300 /
7620
BOLD TYPE indicates maximum piercing parameters.
* Pressure of the water supply line should be regulated by customer pressure regulator.
Note 1: Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic sensing circuit.
Note 2: Water source used for shield must be demineralized.
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB