Owner's manual
Manual 0-4828 Rev BA 8-43 TORCH DATA for Ultra-Cut
Mild Steel
Flow Rates (SLPM / SCFH)
200A Bevel Cut
O₂ Air
Preow
- / - 162 / 343
O₂ Plasma / Air Shield
Culow
102 / 217 133 / 281
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1014 21-1030 21-1285 21-1055 21-1042 21-1093 21-1022
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
inch (in) (psi) Ball (psi) Ball (psi) (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.188 0.080 15 100 100 NA 100 0.130 - 0.550 0.2 0.200 0.150 0.5 0.300 250 0.2 0.142
0.250 0.080 15 100 100 NA 100 0.130 - 0.550 0.2 0.200 0.150 0.5 0.300 200 0.2 0.148
0.375 0.080 15 100 100 NA 100 0.150 - 0.550 0.3 0.250 0.200 0.5 0.350 140 0.3 0.162
0.500 0.080 15 100 100 NA 100 0.170 - 0.550 0.7 0.250 0.200 0.5 0.350 115 0.5 0.167
0.625 0.080 15 100 100 NA 100 0.200 - 0.550 0.9 0.250 0.200 0.5 0.350 80 0.6 0.186
0.750 0.080 15 100 100 NA 100 0.200 - 0.550 1.3 0.300 0.250 0.5 0.400 65 0.8 0.186
0.875 0.080 15 100 100 NA 100 0.200 - 0.550 1.6 0.300 0.250 0.5 0.400 57 1.0 0.185
1.000 0.080 15 100 100 NA 100 0.200 - 0.550 1.9 0.300 0.250 0.5 0.400 48 1.2 0.193
1.250 0.080 15 100 100 NA 100 0.200 - 0.550 3.2 0.325 0.250 0.5 0.425 30 2.0 0.196
1.500 0.080 15 100 100 NA 100 0.200 - 0.550 5.8 0.350 0.300 0.5 0.450 20 4.0 0.201
1.750 0.080 15 100 100 NA 100 0.200 - 0.550 1.0 Edge Start 0.5 Edge 15 1.0 0.203
2.000 0.080 15 100 100 NA 100 0.200 - 0.550 1.0 Edge Start 0.5 Edge 10 1.0 0.204
2.500 0.080 15 100 100 NA 100 0.200 - 0.550 1.0 Edge Start 0.5 Edge 8 1.0 0.210
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (O₂) Shield (Air)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar) (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
5 2.0 1.0 100 6.9 NA 6.9 3.3 - 14.0 0.2 5.1 3.8 0.5 7.6 6170 0.2 3.6
6 2.0 1.0 100 6.9 NA 6.9 3.3 - 14.0 0.2 5.1 3.8 0.5 7.6 5360 0.2 3.7
8 2.0 1.0 100 6.9 NA 6.9 3.6 - 14.0 0.3 5.7 4.5 0.5 8.3 4290 0.3 3.9
10 2.0 1.0 100 6.9 NA 6.9 3.9 - 14.0 0.4 6.4 5.1 0.5 8.9 3460 0.3 4.1
12 2.0 1.0 100 6.9 NA 6.9 4.2 - 14.0 0.6 6.4 5.1 0.5 8.9 3060 0.5 4.2
15 2.0 1.0 100 6.9 NA 6.9 4.9 - 14.0 0.8 6.4 5.1 0.5 8.9 2280 0.6 4.6
20 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.4 7.6 6.4 0.5 10.2 1590 0.9 4.7
25 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.9 7.6 6.4 0.5 10.2 1250 1.2 4.9
30 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 2.8 8.1 6.4 0.5 10.6 890 1.8 5.0
35 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 4.5 8.6 7.0 0.5 11.1 630 3.0 5.0
40 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.0 Edge Start 0.5 Edge 470 1.0 5.1
50 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.0 Edge Start 0.5 Edge 270 1.0 5.2
60 2.0 1.0 100 6.9 NA 6.9 5.1 - 14.0 1.0 Edge Start 0.5 Edge 220 1.0 5.3
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY
8.04 Robotic and Bevel Cutting 150 - 200 Amp