Owner's manual

TORCH DATA for Ultra-Cut 8-44 Manual 0-4828 Rev BA
Stainless Steel
Flow Rates (SLPM / SCFH)
200A Bevel Cut
H35 N₂
Preow
- / - 73 / 154
H35 Plasma / N₂ Shield
Culow
35 / 74 49 / 103
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1015 21-1073 21-1284 21-1095 21-1042 21-1096 21-1022
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H35) Shield (N₂)
inch (in) (psi) Ball (psi) Ball (psi) (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.375 0.080 20 120 100 NA 120 0.300 - 0.550 0.5 0.300 0.250 0.4 0.400 90 0.4 0.131
0.500 0.080 20 120 100 NA 120 0.300 - 0.550 0.8 0.300 0.250 0.3 0.400 65 0.5 0.135
0.625 0.080 20 120 100 NA 100 0.300 - 0.550 1.0 0.250 0.200 0.2 0.350 50 0.6 0.142
0.750 0.080 20 120 100 NA 100 0.300 - 0.550 1.4 0.300 0.250 0.2 0.400 40 0.8 0.143
0.875 0.080 20 120 100 NA 100 0.300 - 0.550 1.8 0.350 0.300 0.2 0.450 35 1.0 0.148
1.000 0.080 20 120 100 NA 120 0.350 - 0.550 2.0 0.350 0.300 0.2 0.450 30 1.0 0.162
1.250 0.080 20 120 100 NA 120 0.350 - 0.550 0.5 Edge Start 0.3 Edge 20 0.5 0.170
1.500 0.080 20 120 100 NA 120 0.350 - 0.550 0.5 Edge Start 0.3 Edge 16 0.5 0.175
1.750 0.080 20 120 100 NA 120 0.350 - 0.550 0.5 Edge Start 0.3 Edge 14 0.5 0.179
2.000 0.080 20 120 100 NA 120 0.350 - 0.550 0.5 Edge Start 0.3 Edge 12 0.5 0.182
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (H35) Shield (N₂)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar) (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
10 2.0 1.4 120 6.9 NA 8.3 7.6 - 14.0 0.5 7.6 6.4 0.4 10.2 2190 0.4 3.3
12 2.0 1.4 120 6.9 NA 8.3 7.6 - 14.0 0.7 7.6 6.4 0.3 10.2 1790 0.5 3.4
15 2.0 1.4 120 6.9 NA 7.3 7.6 - 14.0 0.9 6.7 5.4 0.2 9.2 1380 0.6 3.6
20 2.0 1.4 120 6.9 NA 6.9 7.6 - 14.0 1.5 8.0 6.7 0.2 10.5 980 0.9 3.7
25 2.0 1.4 120 6.9 NA 8.1 8.7 - 14.0 2.0 8.9 7.6 0.2 11.4 780 1.0 4.1
30 2.0 1.4 120 6.9 NA 8.3 8.9 - 14.0 0.5 Edge Start 0.3 Edge 540 0.5 4.3
35 2.0 1.4 120 6.9 NA 8.3 8.9 - 14.0 0.5 Edge Start 0.3 Edge 460 0.5 4.4
40 2.0 1.4 120 6.9 NA 8.3 8.9 - 14.0 0.5 Edge Start 0.3 Edge 390 0.5 4.5
50 2.0 1.4 120 6.9 NA 8.3 8.9 - 14.0 0.5 Edge Start 0.3 Edge 310 0.5 4.6
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-08552
This Art Is For Reference ONLY