Owner's manual

Manual 0-4828 Rev BA 8-47 TORCH DATA for Ultra-Cut
Aluminum
Flow Rates
200A Bevel Cut
N₂ (SLPM / SCFH) H₂O (GPH / LPH)
Preow
13 / 28 5 / 19
N₂ Plasma / H₂O Shield
Culow
28 / 59 5 / 19
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1015 21-1049 21-1284 21-1067 21-1043 21-1089 21-1022
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
inch (in) (psi) Ball (psi) Ball (psi)* (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.500 0.080 20 100 90 5 55 0.250 - 0.550 0.3 0.200 0.150 0.2 0.300 110 0.3 0.120
0.625 0.080 20 80 100 5 55 0.300 - 0.550 0.7 0.250 0.200 0.2 0.350 105 0.5 0.126
0.750 0.080 20 80 100 5 55 0.300 - 0.550 0.9 0.250 0.200 0.2 0.350 90 0.6 0.127
0.875 0.080 20 80 100 5 55 0.300 - 0.550 1.2 0.250 0.200 0.2 0.350 75 0.8 0.133
1.000 0.080 20 80 100 5 55 0.350 - 0.550 1.6 0.300 0.250 0.2 0.400 50 1.0 0.144
1.250 0.080 20 80 100 5 55 0.400 - 0.550 3.4 0.350 0.300 0.2 0.450 25 2.0 0.180
1.500 0.080 20 80 100 5 55 0.400 - 0.550 0.8 Edge Start 0.2 Edge 20 0.8 0.197
1.750 0.080 20 80 100 5 55 0.400 - 0.550 0.8 Edge Start 0.2 Edge 18 0.8 0.201
2.000 0.080 20 80 100 5 55 0.400 - 0.550 0.8 Edge Start 0.2 Edge 12 0.8 0.204
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar)* (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
12 2.0 1.4 100 6.1 5 3.8 6.1 - 14.0 0.2 4.8 3.5 0.2 7.3 2820 0.3 3.0
15 2.0 1.4 85 6.7 5 3.8 7.3 - 14.0 0.6 6.0 4.7 0.2 8.5 2700 0.4 3.2
20 2.0 1.4 80 6.9 5 3.8 7.6 - 14.0 1.0 6.4 5.1 0.2 8.9 2170 0.7 3.3
25 2.0 1.4 80 6.9 5 3.8 8.7 - 14.0 1.5 7.5 6.2 0.2 10.0 1350 1.0 3.6
30 2.0 1.4 80 6.9 5 3.8 9.8 - 14.0 2.9 8.5 7.3 0.2 11.1 810 1.7 4.3
35 2.0 1.4 80 6.9 5 3.8 10.2 - 14.0 0.8 Edge Start 0.2 Edge 530 0.8 5.0
40 2.0 1.4 80 6.9 5 3.8 10.2 - 14.0 0.8 Edge Start 0.2 Edge 490 0.8 5.0
50 2.0 1.4 80 6.9 5 3.8 10.2 - 14.0 0.8 Edge Start 0.2 Edge 320 0.8 5.2
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
* Pressure of the water supply line should be regulated by customer pressure regulator.
Note 1: Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic sensing circuit.
Note 2: Water source used for shield must be demineralized.
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY