Owner's manual

TORCH DATA for Ultra-Cut 8-56 Manual 0-4828 Rev BA
Aluminum
Flow Rates
300A
N₂ (SLPM / SCFH) H₂O (GPH / LPH)
Preow
23 / 48 8 / 30
N₂ Plasma / H₂O Shield
Culow
63 / 134 8 / 30
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1015 21-1046 21-1284 21-1066 21-1043 21-1089 21-1022
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
ga (in) inch (psi) Ball (psi) Ball (psi)* (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
- 1/2 0.500 20 120 100 8 55 160 0.200 0.4 0.250 0.150 0.2 0.300 120 0.3 0.161
- 5/8 0.625 20 120 100 8 55 164 0.200 0.5 0.250 0.150 0.2 0.300 100 0.4 0.165
- 3/4 0.750 20 120 100 8 55 170 0.250 0.9 0.400 0.300 0.2 0.500 80 0.5 0.174
- 7/8 0.875 20 120 100 8 55 173 0.250 1.0 0.400 0.300 0.2 0.500 70 0.6 0.175
- 1 1.000 20 120 100 8 55 175 0.250 1.2 0.400 0.300 0.2 0.500 60 0.7 0.190
- 1 1/4 1.250 20 120 100 8 55 180 0.250 2.2 0.400 0.300 0.2 0.500 40 1.2 0.185
- 1 1/2 1.500 20 120 100 8 55 184 0.300 3.5 Edge Start 0.2 Edge 25 1.6 0.190
- 1 3/4 1.750 20 120 100 8 55 196 0.300 0.6 Edge Start 0.2 Edge 15 0.6 0.213
- 2 2.000 20 120 100 8 55 200 0.300 0.6 Edge Start 0.2 Edge 10 0.6 0.205
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
(mm) (Bar) Ball (Bar) Ball (Bar)* (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
15 1.4 120 6.9 8 3.8 163 5.1 0.5 6.4 3.8 0.2 7.6 2680 0.4 4.2
20 1.4 120 6.9 8 3.8 171 6.4 0.9 10.2 7.6 0.2 12.7 1960 0.5 4.4
25 1.4 120 6.9 8 3.8 175 6.4 1.2 10.2 7.6 0.2 12.7 1560 0.7 4.8
30 1.4 120 6.9 8 3.8 179 6.4 1.9 10.2 7.6 0.2 12.7 1160 1.1 4.7
35 1.4 120 6.9 8 3.8 178 7.6 3.4 Edge Start 0.2 Edge 760 1.6 4.5
40 1.4 120 6.9 8 3.8 188 7.6 2.6 Edge Start 0.2 Edge 560 1.3 5.0
50 1.4 120 6.9 8 3.8 199 7.6 0.6 Edge Start 0.2 Edge 270 0.6 5.2
Marking
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height
THC and CNC
Delay
Control
Delay
Travel
Speed
Marking quality
degrades as
thickness
decreases.
24A Arc Current
Plasma (N₂) Shield (N₂)
Burn-through may
happen for thicknesses
< 1/16” (0.063”) /
1.6 mm.
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) /
(mm/ min)
15 / 1.0 80
60 /
4.1
NA
90 /
6.2
115 0.120 / 3.0 0.120 / 3.0 0 0.3
300 /
7620
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
* Pressure of the water supply line should be regulated by customer pressure regulator.
Note 1: Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic sensing circuit.
Note 2: Water source used for shield must be demineralized.
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY