Owner's manual
TORCH DATA for Ultra-Cut 8-60 Manual 0-4828 Rev BA
Stainless Steel
Flow Rates
300A Bevel Cut
N₂ (SLPM / SCFH) H₂O (GPH / LPH)
Preow
23 / 48 8 / 30
N₂ Plasma / H₂O Shield
Culow
63 / 134 8 / 30
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1015 21-1046 21-1284 21-1066 21-1043 21-1089 21-1022
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
inch (in) (psi) Ball (psi) Ball (psi)* (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.375 0.080 20 120 100 8 55 0.150 - 0.550 0.3 0.250 0.200 0.2 0.350 140 0.3 0.144
0.500 0.080 20 120 100 8 55 0.150 - 0.550 0.5 0.250 0.200 0.2 0.350 100 0.5 0.154
0.625 0.080 20 120 100 8 55 0.150 - 0.550 0.8 0.250 0.200 0.2 0.350 75 0.6 0.153
0.750 0.080 20 120 100 8 55 0.200 - 0.550 0.9 0.400 0.300 0.2 0.500 55 0.7 0.173
0.875 0.080 20 120 100 8 55 0.300 - 0.550 1.8 0.400 0.300 0.2 0.500 45 1.1 0.210
1.000 0.080 20 120 100 8 55 0.300 - 0.550 2.1 0.400 0.300 0.2 0.500 40 1.3 0.210
1.250 0.080 20 120 100 8 55 0.350 - 0.550 3.5 0.400 0.300 0.2 0.500 30 2.0 0.230
1.500 0.080 20 120 100 8 55 0.350 - 0.550 1.0 Edge Start 0.2 Edge 25 1.0 0.232
1.750 0.080 20 120 100 8 55 0.350 - 0.550 1.0 Edge Start 0.2 Edge 18 1.0 0.237
2.000 0.080 20 120 100 8 55 0.350 - 0.550 1.0 Edge Start 0.2 Edge 12 1.0 0.253
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar)* (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
10 2.0 1.4 120 6.9 8 3.8 3.8 - 14 0.3 6.4 5.1 0.2 8.9 3400 0.3 3.7
12 2.0 1.4 120 6.9 8 3.8 3.8 - 14 0.5 6.4 5.1 0.2 8.9 2760 0.5 3.9
15 2.0 1.4 120 6.9 8 3.8 3.8 - 14 0.7 6.4 5.1 0.2 8.9 2080 0.6 3.9
20 2.0 1.4 120 6.9 8 3.8 5.8 - 14 1.2 10.2 7.6 0.2 12.7 1320 0.8 4.7
25 2.0 1.4 120 6.9 8 3.8 7.6 - 14 2.1 10.2 7.6 0.2 12.7 1030 1.3 5.3
30 2.0 1.4 120 6.9 8 3.8 8.5 - 14 3.1 10.2 7.6 0.2 12.7 830 1.8 5.7
35 2.0 1.4 120 6.9 8 3.8 8.9 - 14 1.0 Edge Start 0.2 Edge 720 1.0 5.8
40 2.0 1.4 120 6.9 8 3.8 8.9 - 14 1.0 Edge Start 0.2 Edge 580 1.0 5.9
50 2.0 1.4 120 6.9 8 3.8 8.9 - 14 1.0 Edge Start 0.2 Edge 320 1.0 6.4
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
* Pressure of the water supply line should be regulated by customer pressure regulator.
Note 1: Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic sensing circuit.
Note 2: Water source used for shield must be demineralized.
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-08552
This Art Is For Reference ONLY