Owner's manual

TORCH DATA for Ultra-Cut 8-62 Manual 0-4828 Rev BA
Aluminum
Flow Rates
300A Bevel Cut
N₂ (SLPM / SCFH) H₂O (GPH / LPH)
Preow
23 / 48 8 / 30
N₂ Plasma / H₂O Shield
Culow
63 / 134 8 / 30
Shield Retainer Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1015 21-1046 21-1284 21-1066 21-1043 21-1089 21-1022
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
inch (in) (psi) Ball (psi) Ball (psi)* (in) (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
0.500 0.080 20 120 100 8 55 0.200 - 0.450 0.4 0.250 0.150 0.2 0.300 120 0.3 0.161
0.625 0.080 20 120 100 8 55 0.200 - 0.450 0.5 0.250 0.150 0.2 0.300 100 0.4 0.165
0.750 0.080 20 120 100 8 55 0.250 - 0.450 0.9 0.400 0.300 0.2 0.500 80 0.5 0.174
0.875 0.080 20 120 100 8 55 0.250 - 0.450 1.0 0.400 0.300 0.2 0.500 70 0.6 0.175
1.000 0.080 20 120 100 8 55 0.250 - 0.450 1.2 0.400 0.300 0.2 0.500 60 0.7 0.190
1.250 0.080 20 120 100 8 55 0.250 - 0.450 2.2 0.400 0.300 0.2 0.500 40 1.2 0.185
1.500 0.080 20 120 100 8 55 0.300 - 0.450 3.5 Edge Start 0.2 Edge 25 1.6 0.190
1.750 0.080 20 120 100 8 55 0.300 - 0.450 0.6 Edge Start 0.2 Edge 15 0.6 0.213
2.000 0.080 20 120 100 8 55 0.300 - 0.450 0.6 Edge Start 0.2 Edge 10 0.6 0.205
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Eecve
Material
Thickness
Min.
Clearance
Pre Flow
Pressure
(N₂)
Cut Flow Rates / Pressures
Eecve Cut
Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
(mm) (mm) (Bar) Ball (Bar) Ball (Bar)* (mm) (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
15 2.0 1.4 120 6.9 8 3.8 5.1 - 11.4 0.5 6.4 3.8 0.2 7.6 2680 0.4 4.2
20 2.0 1.4 120 6.9 8 3.8 6.4 - 11.4 0.9 10.2 7.6 0.2 12.7 1960 0.5 4.4
25 2.0 1.4 120 6.9 8 3.8 6.4 - 11.4 1.2 10.2 7.6 0.2 12.7 1560 0.7 4.8
30 2.0 1.4 120 6.9 8 3.8 6.4 - 11.4 1.9 10.2 7.6 0.2 12.7 1160 1.1 4.7
35 2.0 1.4 120 6.9 8 3.8 7.6 - 11.4 3.4 Edge Start 0.2 Edge 760 1.6 4.5
40 2.0 1.4 120 6.9 8 3.8 7.6 - 11.4 2.6 Edge Start 0.2 Edge 560 1.3 5.0
50 2.0 1.4 120 6.9 8 3.8 7.6 - 11.4 0.6 Edge Start 0.2 Edge 270 0.6 5.2
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
* Pressure of the water supply line should be regulated by customer pressure regulator.
Note 1: Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic sensing circuit.
Note 2: Water source used for shield must be demineralized.
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-08552
This Art Is For Reference ONLY