Owner's manual

TORCH DATA for Ultra-Cut 8-68 Manual 0-4828 Rev BA
Stainless Steel
400A
N₂ Plasma / H₂O Shield
Flow Rates
N₂ (SLPM / SCFH)
H₂O (GPH /
LPH)
Preow
22 / 47 8 / 30
Culow 72 / 153 8 / 30
Shield Cup Shield Cap Shield Gas Distributor Tip Plasma Gas Distributor Electrode Cartridge
21-1305 21-1501 21-1500 21-1302 21-1043 21-1502 21-1300
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N2)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC Moon
Delay
Max Kerf
Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
ga (in) inch (psi) Ball (psi) Ball (psi)* (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
- 3/8 0.375 17 150 119 8 NA 163 0.200 0.4 0.400 0.300 0.2
Not Recommended without
Elevaon Height
150 0.3 0.132
- 1/2 0.500 17 150 119 8 NA 164 0.200 0.6 0.450 0.300 0.2 130 0.4 0.200
- 5/8 0.625 17 150 119 8 NA 164 0.200 0.8 0.450 0.400 0.2 110 0.6 0.200
- 3/4 0.750 17 150 119 8 NA 166 0.200 1.2 0.450 0.400 0.2 90 0.7 0.200
- 1 1.000 17 150 119 8 NA 171 0.200 2.0 0.450 0.400 0.2 75 1.0 0.230
- 1 1/4 1.250 17 150 119 8 NA 179 0.250 2.5 0.450 0.450 0.2 40 1.5 0.230
- 1 1/2 1.500 17 150 119 8 NA 184 0.250 3.0 0.450 0.500 0.2 30 2.3 0.240
- 1 3/4 1.750 17 150 119 8 NA 193 0.300 3.5 0.450 0.500 0.2 25 2.7 0.245
- 2 2.000 17 150 119 8 NA 201 0.300 4.0 Edge Start 0.2 17 4.0 0.245
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(N2)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC Moon
Delay
Max Kerf
Width
@ Rec. Speed
Plasma (N₂) Shield (H₂O)
(mm) (Bar) Ball (Bar) Ball (Bar)* (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
10 1.2 150 8.2 8 NA 163 5.1 0.4 10.4 7.6 0.2
Not Recommended without
Elevaon Height
3730 0.3 3.6
12 1.2 150 8.2 8 NA 164 5.1 0.6 11.2 7.6 0.2 3410 0.4 4.7
15 1.2 150 8.2 8 NA 164 5.1 0.7 11.4 9.5 0.2 2930 0.5 5.1
20 1.2 150 8.2 8 NA 167 5.1 1.3 11.4 10.2 0.2 2230 0.7 5.2
25 1.2 150 8.2 8 NA 171 5.1 1.9 11.4 10.2 0.2 1930 1.0 5.8
30 1.2 150 8.2 8 NA 177 6.0 2.4 11.4 11.1 0.2 1260 1.4 5.8
40 1.2 150 8.2 8 NA 187 6.7 3.1 11.4 12.7 0.2 720 2.4 6.1
50 1.2 150 8.2 8 NA 200 7.6 3.9 Edge Start 0.2 460 3.8 6.2
Marking
45A Arc Current
Burn-through
may happen for
thicknesses <
1/16” (0.063”) /
1.6mm.
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height THC and CNC Delay
Control
Delay
Travel
Speed
Marking
quality
degrades as
thickness
decreases.
Plasma (N₂) Shield (N₂)
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) / (mm/
min)
15 / 1.0 80
60 /
4.1
NA
90 /
6.2
123 0.400 / 10.2 0.400 / 10.2 0 0 200 / 5080
BOLD TYPE indicates maximum piercing parameters. BOLD ITALIC indicates edge starts only.
BOLD TYPE indicates maximum piercing parameters.
* Pressure of the water supply line should be regulated by customer pressure regulator.
Note 1: Ohmic height sensing is not recommended with water shield. Water on the plate interferes electrically with the ohmic sensing circuit.
Note 2: Water source used for shield must be demineralized.
This Art Is For Reference Only
Shield Cup
Shield Cap
Shield Gas
Distributor
Tip
Gas
Distributor
Electrode
Cartridge Assembly
Art# A-10445