Owner's manual

TORCH DATA for Ultra-Cut 8-8 Manual 0-4828 Rev BA
Stainless Steel
Flow Rates (SLPM / SCFH)
30A
Air
Preow
22 / 47
Air Plasma / Air Shield
Culow
40 / 85
Shield Cup Shield Cap
Shield Gas
Distributor
Tip Plasma Gas Distributor Electrode Cartridge
21-1016 21-1033 21-1274 21-1059 21-1045 21-1077 21-1020
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (Air) Shield (Air)
ga (in) inch (psi) Ball (psi) Ball (psi) (Volts) (in) ±0.005 (sec) (in) (in) (sec) (in) (ipm) (sec) (in)
26 - 0.019 60 64 120 20 120 87 0.020 0.0 0.040 0.030 0.7 0.040 350 0.0 0.029
24 - 0.025 60 64 120 20 120 85 0.020 0.0 0.040 0.030 0.7 0.040 320 0.0 0.028
22 - 0.031 60 64 120 20 120 80 0.020 0.0 0.040 0.030 0.7 0.040 310 0.0 0.034
20 - 0.038 60 64 120 20 120 75 0.020 0.1 0.060 0.040 0.6 0.060 300 0.1 0.025
18 - 0.050 60 64 120 20 120 78 0.020 0.2 0.070 0.040 0.5 0.080 150 0.2 0.032
16 - 0.063 60 64 120 20 120 76 0.020 0.2 0.070 0.040 0.5 0.080 110 0.2 0.030
GCM-2010 SC-3000 Torch Height Control (THC) Basic THC CNC Control
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates / Pressures
Arc
Voltage
Cut Height
THC
Pierce
Delay
Pierce
Ignion
Height
Elevaon
Height
Control
Delay
Pierce
Height
without
Elevaon
Travel
Speed
CNC
Moon
Delay
Max Kerf Width
@ Rec. Speed
Plasma (Air) Shield (Air)
(mm) (Bar) Ball (Bar) Ball (Bar) (Volts) (mm) ±0.1 (sec) (mm) (mm) (sec) (mm)
(mm/
min)
(sec) (mm)
0.6 4.1 64 8.3 20 8.3 85 0.5 0.0 1.0 0.8 0.7 1.0 8300 0.0 0.7
0.8 4.1 64 8.3 20 8.3 80 0.5 0.0 1.1 0.8 0.7 1.1 7860 0.0 0.8
1 4.1 64 8.3 20 8.3 75 0.5 0.1 1.6 1.0 0.6 1.6 7190 0.1 0.7
1.5 4.1 64 8.3 20 8.3 77 0.5 0.2 1.8 1.0 0.5 2.0 3100 0.2 0.8
2 4.1 64 8.3 20 8.3 74 0.5 0.2 1.8 1.0 0.5 2.0 2600 0.2 0.7
Marking
Pre Flow
Pressure
(N₂)
Marking Flow Rates /
Pressures
Arc
Voltage
Marking
Height
Pierce Ignion Height
THC and CNC
Delay
Control
Delay
Travel
Speed
Marking quality
degrades as
thickness
decreases.
16A Arc Current
Plasma (N₂) Shield (N₂)
Burn-through may
happen for thicknesses
< 1/16” (0.063”) /
1.6 mm.
(psi) /
(Bar)
Ball
(psi) /
(Bar)
Ball
(psi) /
(Bar)
(Volts)
(in) ±0.005 /
(mm) ±0.1
(in) ±0.005 / (mm) ±0.1 (sec) (sec)
(ipm) /
(mm/ min)
20 / 1.4 20
40 /
2.8
70
80 /
5.5
93 0.100 / 2.5 0.100 / 2.5 0 0.4
300 /
7620
BOLD TYPE indicates maximum piercing parameters.
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB