User guide

TORCH DATA 8-32 Manual 0-4801 Rev. AJ
(ga) (in) inch (PSI) (Ball) (PSI)
(Ball)
(PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/8 0.375 20 100 100 NA 110 165 0.300 180 0.400 0.4 0.113
1/2 0.500 20 100 100 NA 110 168 0.300 150 0.350 0.2 0.119
5/8 0.625 20 100 100 NA 110 170 0.300 110 0.350 0.3 0.120
3/4 0.750 20 100 100 NA 110 172 0.300 70 0.400 0.4 0.130
7/8 0.875 20 100 100 NA 110 178 0.350 55 0.450 0.5 0.139
1 1.000 20 100 100 NA 110 180 0.350 40 0.500 0.7 0.150
1 1/4 1.250 20 100 100 NA 110 185 0.400 32 0.161
1 1/2 1.500 20 100 100 NA 110 195 0.400 25 0.170
2 2.000 20 100 100
NA
110 201 0.400 15 0.205
(Bar) (Ball) (Bar)
(Ball)
(Bar) Volts
(mm)
±0.1
(mm/min)
(mm) (sec) (mm)
1.4 100 6.9 NA 7.6 166 7.6 4500 10.2 0.4 2.9
1.4 100 6.9 NA 7.6 168 7.6 3850 8.9 0.2 3.0
1.4 100 6.9 NA 7.6 170 7.6 2800 8.9 0.3 3.0
1.4 100 6.9 NA 7.6 174 7.6 1600 10.2 0.5 3.3
1.4 100 6.9 NA 7.6 180 8.9 1050 12.7 0.7 3.8
1.4 100 6.9 NA 7.6 185 10.2 800 4.1
1.4 100 6.9 NA 7.6 195 10.2 640 4.3
1.4 100 6.9 NA 7.6 198 10.2 450 4.8
1.4 100 6.9 NA 7.6 200 10.2 380 5.2
Torch
Working
Height
Aluminum
200A
H35 Plasma / N
2
Shield
Travel
Speed
Initial
Piercing
Height
Material
Thickness
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures
Cut Flow Rates /
Pressures
NOTE:
Lock pierce height between 0.5" to 1" to avoid torch hitting the pierce metal puddle.
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later
Pierce
Delay
Kerf Width
@ Rec.
Speed
Plasma (H35)
Shield (N
2
)
Kerf Width
@ Rec.
Speed
Plasma
(H35)
38
Shield
Retainer
Shield Cap
Shield Gas
Distributor
Arc
Voltage
Tip
Plasma Gas
Distributor
Electrode Cartridge
21-1043 21-1096 21-102221-1015
< 1" / 25mm 21-1073
1" / 25mm + 21-1094
21-1284 21-1095
10
Travel
Speed
Initial
Piercing
Height
Pierce
DelayShield
(Air)
Arc
Voltage
Torch
Working
Height
(mm)
Material
Thickness
Pre Flow
Pressure
(N
2
)
25
50
Edge Start
Edge Start
12
32
44 Edge Start
15
20
Edge Start
Edge Start
Edge Start
Edge Start
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY