User guide

Manual 0-4801 Rev. AJ 8-9 TORCH DATA
(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/16 0.188 15 100 100 NA 100 151 0.130 250 0.300 0.2 0.142
1/4 0.250 15 100 100 NA 100 151 0.130 200 0.300 0.2 0.148
3/8 0.038 15 100 100 NA 100 154 0.150 140 0.350 0.3 0.162
1/2 0.500 15 100 100 NA 100 159 0.170 115 0.350 0.5 0.167
5/8 0.625 15 100 100 NA 100 161 0.200 80 0.350 0.6 0.186
3/4 0.750 15 100 100 NA 100 163 0.200 65 0.400 0.8 0.186
7/8 0.875 15 100 100 NA 100 166 0.200 57 0.400 1.0 0.185
1 1.000 15 100 100 NA 100 167 0.200 48 0.400 1.2 0.193
1 1/4 1.250 15 100 100 NA 100 170 0.200 30 0.425 2.0 0.196
1 1/2 1.500 15 100 100
NA
100 185 0.200 20 0.450 4.0 0.201
2 2.000 15 100 100
NA
100 192 0.200 10 0.204
(Bar) (Ball) (Bar) (Ball) (Bar) Volts
(mm)
±0.1
(mm/min)
(mm) (sec) (mm)
1.0 100 6.9 NA 6.9 151 3.3 6170 7.6 0.2 3.6
1.0 100 6.9 NA 6.9 151 3.3 5360 7.6 0.2 3.7
1.0 100 6.9 NA 6.9 153 3.6 4290 8.3 0.3 3.9
1.0 100 6.9 NA 6.9 155 3.9 3460 8.9 0.3 4.1
1.0 100 6.9 NA 6.9 158 4.2 3060 8.9 0.5 4.2
1.0 100 6.9 NA 6.9 160 4.0 2280 8.9 0.6 4.6
1.0 100 6.9 NA 6.9 164 5.1 1590 10.2 0.9 4.7
1.0 100 6.9 NA 6.9 167 5.1 1250 10.2 1.2 4.9
1.0 100 6.9 NA 6.9 171 5.1 750 10.8 2.1 5.0
1.0 100 6.9 NA 6.9 185 5.1 510 11.4 4.0 5.1
1.0 100 6.9
NA
6.9 188 5.1 390 5.1
1.0 100 6.9
NA
6.9 192 5.1 270 5.2
Mild Steel
200A
O
2
Plasma / Air Shield
NOTE:
Lock pierce height between 0.5" to 1" to avoid torch hitting the pierce metal puddle.
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later
Pierce
Delay
Kerf Width
@ Rec.
SpeedPlasma (O
2
) Shield (Air)
Kerf Width
@ Rec.
Speed
Plasma (O
2
)
38
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Arc
Voltage
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
6
Shield
Retainer
Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
21-1042 21-1093 21-102221-1014 21-1030 21-1285 21-1055
10
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Shield (Air)
Arc
Voltage
Torch
Working
Height
(mm)
5
8
25
50
Edge Start
Edge Start
12
32
44 Edge Start
15
20
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY