Owner's manual

Manual 0-4829 Rev AN 8-15 TORCH DATA for Ultra-Cut
(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
14 0.078 100 62 120 75 120 109 0.060 180 0.120 0.0 0.044
12 0.109 100 62 120 75 120 114 0.060 130 0.150 0.0 0.049
10 0.141 100 62 120 75 120 118 0.060 120 0.180 0.1 0.050
3/16
0.188 100 62 120 75 120 124 0.080 70 0.200 0.3 0.059
(Bar) (Ball) (Bar) (Ball) (Bar) Volts
(mm)
±0.1
( mm/min)
(mm) (sec) (mm)
6.9 62.0 8.3 75.0 8.3 106.0 1.5 5350.0 2.6 0.0 1.0
6.9 62.0 8.3 75.0 8.3 109.0 1.5 4540.0 3.1 0.0 1.1
6.9 62.0 8.3 75.0 8.3 115.0 1.5 3229.7 4.0 0.0 1.3
6.9 62.0 8.3 75.0 8.3 120.0 1.7 2600.0 4.8 0.2 1.4
6.9 62.0 8.3 75.0 8.3 125.0 2.1 1520.0 5.2 0.3 1.5
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
Volts
in ±0.005 /
mm ±0. 1
ipm /
mm/min
in ±0.005 /
mm ±0.1
(sec)
20 40 80 0.120 300 0.120
1.4 2.8 5.5 3.0 7600 3.0
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Pierce
Delay
Marki ng
quality
degrades
as
thickness
decreases
Burn-through
may occur
for thickness es
< 1/16" (0.063") / 1.6
mm.
Plasma (N
2
) Shield (N
2
)
40 75 120 0
4
5
Marking
16A Arc Current
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures Arc
Volta ge
Torch
Working
Height
Travel
Speed
Initial
Trans fer
Height
(mm)
1.5
2.0
3.0
Pierce
Delay
Kerf Width
@ Rec.
Speed
Plasma (Air) Shield (Air)
Kerf Width
@ Rec.
SpeedPlasma (Air) Shield (Air)
Mate ri a l
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures Arc
Volta ge
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Mate ri a l
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Arc
Volta ge
22-1041 22-1078 22-102022-1016 22-1034 22-1274 22-1060
Stainless Steel
50A
Air Plasma / Air Shield
Shield Cup Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB