Owner's manual

Manual 0-4829 Rev AN 8-43 TORCH DATA for Ultra-Cut
(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
1/4 0.250 70 60 90 8 55 135 0.100 110 0.250 0.3 0.104
3/8 0.375 70 60 90 8 55 139 0.100 70 0.350 0.3 0.107
1/2 0.500 70 60 90 8 55 149 0.150 60 0.350 0.5 0.111
5/8 0.625 70 60 90 8 55 159 0.180 45 0.350 0.5 0.128
3/4 0.750 70 60 90 4 55 159 0.180 40 0.350 0.9 0.130
(Bar) (Ball) (Bar) (Ball) (Bar) Volts
(mm)
±0.1
( mm/min)
(mm) (sec) (mm)
4.8 60 6.2 8 3.8 137.0 2.5 2265 6.4 0.3 2.7
4.8 60 6.2 8 3.8 140.0 2.5 1740 8.9 0.3 2.7
4.8 60 6.2 8 3.8 147.5 3.8 1580 8.9 0.5 2.8
4.8 60 6.2 8 3.8 156.2 4.6 1248 8.9 0.5 3.2
4.8 60 6.2 4 3.8 162.0 4.6 1010 8.9 0.9 3.3
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
Volts
in ±0.005 /
mm ±0. 1
ipm /
mm/min
in ±0.005 /
mm ±0.1
(sec)
20 60 80 0.120 300 0.120
1.4 4.1 5.5 3.0 7600 3.0
12.0
15.0
20.0
Mate ri a l
Thickness
22-1016
Marking
17A Arc Current
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures Arc
Volta ge
Torch
Working
Height
(mm)
8.0
10.0
Stainless Steel
150A
N
2
Plasma / H
2
O Shield
Shield Cup Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
22-1048 22-1278 22-1092 22-1041 22-1081 22-1020
Mate ri a l
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Arc
Volta ge
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf Width
@ Rec.
SpeedPlasma (N
2
)
Shield
(H
2
O)*
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures Arc
Volta ge
Torch
Working
Height
Plasma (N
2
)
Shield
(H
2
O)*
Initial
Trans fer
Height
Pierce
Delay
Marki ng
quality
degrades
as
thickness
decreases
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf Width
@ Rec.
Speed
130 0
BOLD TYPE
indicates maximum piercing parameters.
Burn-through
may occur
for thickness es
< 1/16" (0.063") / 1.6
mm.
Plasma (N
2
) Shield (N
2
)
60 75
Travel
Speed
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB