Owner's manual

Manual 0-4829 Rev AN 8-45 TORCH DATA for Ultra-Cut
(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/16 0.188 70 60 90 8 55 130 0.100 150 0.350 0.2 0.107
1/4 0.250 70 60 90 8 55 133 0.120 120 0.350 0.2 0.108
3/8 0.375 70 60 90 8 55 140 0.120 100 0.350 0.2 0.116
1/2 0.500 70 60 90 8 55 152 0.200 75 0.350 0.3 0.126
5/8 0.625 70 60 90 8 55 155 0.200 50 0.350 0.4 0.142
3/4 0.750 70 60 90 8 55 165 0.250 35 0.350 0.5 0.141
1 1.000 70 60 90 8 55 178 0.300 20 0.350 1.0 0.155
(Bar) (Ball) (Bar) (Ball) (Bar) Volts
(mm)
±0.1
( mm/min)
(mm) (sec) (mm)
4.8 60 6.2 8 3.8 130 2.5 3700 8.9 0.2 2.7
4.8 60 6.2 8 3.8 132 3.0 3220 8.9 0.2 2.7
4.8 60 6.2 8 3.8 137 3.0 2785 8.9 0.2 2.8
4.8 60 6.2 8 3.8 142 3.0 2445 8.9 0.2 2.9
4.8 60 6.2 8 3.8 149 5.1 2050 8.9 0.3 3.2
4.8 60 6.2 8 3.8 154 5.1 1445 8.9 0.4 3.4
4.8 60 6.2 8 3.8 167 6.4 830 8.9 0.5 3.7
4.8 60 6.2 8 3.8 177 7.6 535 8.9 1.0 3.9
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
Volts
in ±0.005 /
mm ±0. 1
ipm /
mm/min
in ±0.005 /
mm ±0.1
(sec)
20 60 80 0.120 300 0.120
1.4 4.1 5.5 3.0 7600 3.0
130 0
BOLD TYPE
indicates maximum piercing parameters.
Burn-through
may occur
for thickness es
< 1/16" (0.063") / 1.6
mm.
Plasma (N
2
) Shield (N
2
)
60 75
Travel
Speed
Initial
Trans fer
Height
Pierce
Delay
Marki ng
quality
degrades
as
thickness
decreases
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf Width
@ Rec.
Speed
Kerf Width
@ Rec.
SpeedPlasma (N
2
)
Shield
(H
2
O)*
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures Arc
Volta ge
Torch
Working
Height
Plasma (N
2
)
Shield
(H
2
O)*
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Mate ri a l
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Arc
Volta ge
Aluminum
150A
N
2
Plasma / H
2
O Shield
Shield Cup Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
Torch
Working
Height
(mm)
5
6
17A Arc Current
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures Arc
Volta ge
25
15
22-1016
Marking
22-1048 22-1278 22-1092 22-1041 22-1081 22-1020
20
12
8
10
Mate ri a l
Thickness
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB