Owner's manual

Manual 0-4829 Rev AN 8-47 TORCH DATA for Ultra-Cut
(ga) (in) inch (PSI) (Ball) (PSI)
(Ball)
(PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/8 0.375 20 120 100 NA 120 168 0.300 90 0.400 0.4 0.131
1/2 0.500 20 120 100 NA 120 170 0.300 65 0.400 0.5 0.135
5/8 0.625 20 120 100 NA 100 173 0.300 50 0.350 0.6 0.142
3/4 0.750 20 120 100 NA 100 175 0.300 40 0.400 0.8 0.143
7/8 0.875 20 120 100 NA 100 178 0.300 35 0.450 1.0 0.148
1 1.000 20 120 100 NA 120 184 0.350 30 0.450 1.0 0.162
1 1/4 1.250 20 120 100 NA 120 185 0.350 20 0.170
1 1/2 1.500 20 120 100 NA 120 190 0.350 16 0.175
2 2.000 20 120 100 NA 120 193 0.350 12 0.182
(Bar) (Ball) (Bar)
(Ball)
(Bar) Volts
(mm)
±0.1
( mm/min)
(mm) (sec) (mm)
1.4 120 6.9 NA 8.3 168 7.6 2200 10.2 0.3 3.4
1.4 120 6.9 NA 8.3 170 7.6 1700 10.2 0.5 3.4
1.4 120 6.9 NA 6.9 172 7.6 1300 8.9 0.6 3.6
1.4 120 6.9 NA 6.9 176 7.6 950 10.2 0.9 3.7
1.4 120 6.9 NA 8.3 183 8.9 770 11.4 1.2 4.0
1.4 120 6.9 NA 8.3 186 8.9 500
Edge
Start
0.0 4.3
1.4 120 6.9
NA
8.3 190 8.9 400
Edge
Start
0.0 4.4
1.4 120 6.9
NA
8.3 192 8.9 340 4.5
1.4 120 6.9
NA
8.3 193 8.9 300 4.6
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
Volts
in ±0.005 /
mm ±0.1
ipm /
mm/ min
in ±0.005 /
mm ±0.1
(sec)
15 60 80 0.120 300 0.120
1.0 4.1 5.5 3.0 7600 3.0
140 0
Plasma (N
2
) Shield (N
2
)
80 NA
Marking
20A Arc Current
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures Arc
Vo l tage
Torch
Working
Height
Travel
Speed
Initial
Transfer
Height
Pierce
Delay
Ma rki n g
quality
degrades
as
thickness
decreases
Stainless Steel
200A
H35 Plasma / N
2
Shield
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later
22-102222-1015 22-1073 22-1284 22-1095
Ma te ri a l
Thickness
Pre Flow
Pressure
(N
2
)
NOTE:
Lock pierce height between 0.5" to 1" to avoid torch hitting the pierce metal puddle.
Shield
Retainer
Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
22-1042 22-1096
Initial
Piercing
Height
Pierce
Delay
Edge Start
Edge Start
Edge Start
Kerf Width
@ Rec.
Speed
Plasma (H35)
Shield (N
2
)
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Cut Flow Rates /
Pressures Arc
Vo l tage
Kerf Width
@ Rec.
Speed
Plasma (O
2
) Shield (Air)
(mm)
Ma te ri a l
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Arc
Vo l tage
Torch
Working
Height
Travel
Speed
50 Edge Start
25
32
38
44 Edge Start
12
15
20
10
Cartridge
Electrode
Shield
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Shield Retainer
Art # A-07917_AC
This Art Is For Reference ONLY