Owner's manual

Manual 0-4829 Rev AN 8-49 TORCH DATA for Ultra-Cut
(ga) (in) inch (PSI) (Ball) (PSI)
(Ball)
(PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/8 0.375 20 100 100 NA 110 165 0.300 180 0.400 0.4 0.113
1/2 0.500 20 100 100 NA 110 168 0.300 150 0.350 0.2 0.119
5/8 0.625 20 100 100 NA 110 170 0.300 110 0.350 0.3 0.120
3/4 0.750 20 100 100 NA 110 172 0.300 70 0.400 0.4 0.130
7/8 0.875 20 100 100 NA 110 178 0.350 55 0.450 0.5 0.139
1 1.000 20 100 100 NA 110 180 0.350 40 0.500 0.7 0.150
1 1/4 1.250 20 100 100 NA 110 185 0.400 32 0.161
1 1/2 1.500 20 100 100 NA 110 195 0.400 25 0.170
2 2.000 20 100 100 NA 110 201 0.400 15 0.205
(Bar) (Ball) (Bar)
(Ball)
(Bar) Volts
(mm)
±0.1
(mm/min)
(mm) (sec) (mm)
1.4 100 6.9 NA 7.6 166 7.6 4500 10.2 0.4 2.9
1.4 100 6.9 NA 7.6 168 7.6 3850 8.9 0.2 3.0
1.4 100 6.9 NA 7.6 170 7.6 2800 8.9 0.3 3.0
1.4 100 6.9 NA 7.6 174 7.6 1600 10.2 0.5 3.3
1.4 100 6.9 NA 7.6 180 8.9 1050 12.7 0.7 3.8
1.4 100 6.9 NA 7.6 185 10.2 800
Edge
Start
0.0 4.1
1.4 100 6.9
NA
7.6 195 10.2 640
Edge
Start
0.0 4.3
1.4 100 6.9
NA
7.6 198 10.2 450 4.8
1.4 100 6.9
NA
7.6 200 10.2 380 5.2
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
Volts
in ±0.005 /
mm ±0.1
ipm /
mm/ min
in ±0.005 /
mm ±0. 1
(sec)
15 60 80 0.120 300 0.120
1.0 4.1 5.5 3.0 7600 3.0
140 0
Plasma (N
2
) Shield (N
2
)
80 NA
Marking
20A Arc Current
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures Arc
Voltag e
Torch
Working
Height
Travel
Speed
Initial
Transfer
Height
Pierce
Delay
Marki ng
quality
degrades
as
thickness
decreases
Aluminum
200A
H35 Plasma / N
2
Shield
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later
22-102222-1015
< 1" / 25mm 22-1073
1" / 25mm + 22-1094
22-1284 22-1095
Mate ri a l
Thickness
Pre Flow
Pressure
(N
2
)
NOTE:
Lock pierce height between 0.5" to 1" to avoid torch hitting the pierce metal puddle.
Shield
Retainer
Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
22-1043 22-1096
Initial
Piercing
Height
Pierce
Delay
Edge Start
Edge Start
Edge Start
Kerf Width
@ Rec.
Speed
Plasma (H35)
Shield (N
2
)
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
C
ut Flow Rates
/
Pressures Arc
Voltag e
Kerf Width
@ Rec.
Speed
Plasma (O
2
) Shield (Air)
(mm)
Mate ri a l
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Arc
Voltag e
Torch
Working
Height
Travel
Speed
50 Edge Start
25
32
38
44 Edge Start
12
15
20
10
Electrode
Shield Retainer
Tip
Art # A-08567
Plasma Gas
Distributor
Cartridge Assembly
This Art Is For Reference ONLY
Shield Cap
Shield Gas
Distributor