Owner's manual

TORCH DATA for Ultra-Cut 8-56 Manual 0-4829 Rev AN
Shield
22-1073
22-1094
in in (PSI) (Ball) (PSI)
(Ball)
(PSI) (ipm) (in) (sec) (in)
3/8 0.07 20 120 100 NA 120 90 0.400 0.4 0.131
1/2 0.07 20 120 100 NA 120 65 0.400 0.5 0.135
5/8 0.07 20 120 100 NA 100 50 0.350 0.6 0.142
3/4 0.07 20 120 100 NA 100 40 0.400 0.8 0.143
7/8 0.07 20 120 100 NA 100 35 0.450 1.0 0.148
1 0.07 20 120 100 NA 120 30 0.450 1.0 0.162
1 1/4
0.07
20 120 100 NA 120 20 0.170
1 1/2
0.07
20 120 100 NA 120 16 0.175
2
0.07
20 120 100 NA 120 12 0.182
mm mm (Bar) (Ball) (Bar)
(Ball)
(Bar)
( mm/ min )
(mm) (sec) (mm)
10 1.8 1.4 120 6.9 NA 8.3 2200 10.2 0.3 3.4
12 1.8 1.4 120 6.9 NA 8.3 1700 10.2 0.5 3.4
15 1.8 1.4 120 6.9 NA 6.9 1300 8.9 0.6 3.6
20 1.8 1.4 120 6.9 NA 6.9 950 10.2 0.9 3.7
25 1.8 1.4 120 6.9 NA 8.3 770 11.4 1.2 4.0
32 1.8 1.4 120 6.9 NA 8.3 500 4.3
38 1.8 1.4 120 6.9 NA 8.3 400 4.4
44 1.8 1.4 120 6.9 NA 8.3 340 4.5
50 1.8 1.4 120 6.9 NA 8.3 300 4.6
Stainless Steel
200A Bevel Cut
H35 Plasma / N
2
Shield
Electrode Cartridge
22-1096
Shield
Retainer
Shield Gas
Distributor
Tip
22-1022
Plasma Gas
Distributor
Minimum Clearance
22-1042
Eff
ec
ti
ve
Material
Thi
c
kn
ess
Minimum
Clearance
Eff
ec
ti
ve
Material
Thi
c
kn
ess
22-1015 22-1284 22-1095
Edge Start
Edge Start
Edge Start
Effective Cut Height
(in)
.300-.450
.300-.451
.300-.452
.300-.453
.300-.454
.300-.455
Kerf Width
@ Rec.
Speed
Plasma (H35)
Shield (N
2
)
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
C
ut Flow Rates
/
Pressures
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later
Pre Flow
Pressure
(N
2
)
Kerf Width
@ Rec.
Speed
Plasma (O
2
) Shield (Air)
Pre Flow
Pressure
(Air)
C
ut Flow Rates
/
Pressures
Travel
Speed
Pierce
Delay
Initial
Piercing
Height
Edge Start
Edge Start
Edge Start
Edge Start
.300-.456
.300-.457
.300-.458
Effective Cut Height
(mm)
7.6-13.97
7.6-13.97
7.6-13.97
8.9-13.97
8.9-13.97
7.6-13.97
8.9-13.97
8.9-13.97
8.9-13.97
Electrode
Shield Retainer
Tip
Art # A-08567
Plasma Gas
Distributor
Cartridge Assembly
This Art Is For Reference ONLY
Shield Cap
Shield Gas
Distributor