Owner's manual
TORCH DATA for Ultra-Cut 8-66 Manual 0-4829 Rev AN
Stainless Steel
300A
H35 Plasma / N
2
Shield
(ga) (in) inch psi Ball psi Ball psi Volts
(in)
±0.005
(ipm) (in) (sec) (in)
1/2 0.500 15 104 90 NA 40 147 0.130 150 0.400 0.4 0.190
-1282
5/8 0.625 15 104 100 NA 50 152 0.130 115 0.400 0.5 0.190
-1282
3/4 0.750 15 104 100 NA 60 154 0.140 100 0.450 0.7 0.190
-1282
7/8 0.875 15 104 100 NA 60 155 0.140 85 0.450 0.8 0.190
-1282
1 1.000 15 104 100 NA 60 160 0.150 70 0.450 0.9 0.195
-1282
1.25 1.250 15 104 100 NA 60 169 0.220 50 0.450 1.0 0.230
-1283
1 1/2 1.500 15 104 100 NA 80 176 0.230 35 0.450 1.7 0.245
-1283
1 3/4 1.750 15 104 100
NA
90 182 0.230 25 0.450 3.000 0.275
-1283
2 2.000 15 104 100 NA 90 187 0.230 18 0.280
-1283
2 1/2 2.500 15 104 100 NA 90 208 0.230 10 NA
-1283
3 3.000 15 104 100 NA 90 219 0.230 7 NA -1283
bar Ball bar Ball bar Volts
(mm)
±0.1
( mm/min)
(mm) (sec) (mm)
1 104 6.2 NA 2.8 146 3.3 3810 10.2 0.4 4.8
-1282
1 104 6.9 NA 3.5 151 3.3 2920 10.2 0.5 4.8
-1282
1 104 6.9 NA 4.1 155 3.6 2540 12.7 0.7 4.8
-1282
1 104 6.9 NA 4.1 160 3.8 1780 12.7 0.9 5.0
-1282
1 104 6.9 NA 4.1 168 5.6 1270 12.7 1.0 5.8
-1283
1 104 6.9 NA 5.5 175 5.8 900 12.7 1.7 6.2
-1283
1 104 6.9
NA
6.2 180 5.8 660 12.7 3.0 6.6
-1283
1 104 6.9
NA
6.2 187 5.8 460 7.1
-1283
1 104 6.9
NA
6.2 201 7.6 325 NA
-1283
1 104 6.9
NA
6.2 212 7.6 285 NA -1283
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
(Ball)
(PSI) /
(Bar)
Vo l ts
in ±0.005 /
mm ±0. 1
ipm /
mm/min
in ±0.005 /
mm ±0.1
(sec)
15 60 90 0.120 300 0.120
1.0 4.1 6.2 3.0 7600 3.0
Mild Steel
300A
O
2
Plasma / Air Shield
Shield
Retainer
Shield Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode Cartridge
22-1042 22-1090 22-102222-1021 22-1029
22-1282
22-1283
22-1057
Material
Thickness
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures Arc
Volta g e
Kerf Width
@ Rec.
Speed
Shield
Gas
Distributor
Plasma (O
2
) Shield (Air)
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Edge Start
Edge Start
Edge Start
Material
Thickness
Pre Flow
Pressure
(Air
2
)
Cut Flow Rates /
Pressures Arc
Volta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf Width
@ Rec.
Speed
Shield
Gas
Distributor
Plasma (O
2
) Shield (Air)
(mm)
12
15
20
25
30
35
40
70
Edge Start
50 Edge Start
60 Edge Start
Marking
30A Arc Current
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures Arc
Volta g e
Torch
Working
Height
Travel
Speed
Initial
Transfer
Height
Pierce
Delay
Marking
quality
degrades
as
thickness
decreases
158 0
BOLD TYPE
indicates m axim um piercing param eters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later
Plasma (N
2
) Shield (N
2
)
80 NA
Electrode
Shield Cap
Shield Retainer
Tip
Shield Gas Distributor
Art # A-08551_AB
Plasma Gas
Distributor
(Straight)
(Swirl)
Cartridge Assembly
This Art Is For Reference ONLY