Owner's manual

Manual 0-4829 Rev AN 8-73 TORCH DATA for Ultra-Cut
Shield
22-1029
in in psi Ball psi Ball psi (ipm) (in) (sec) (in)
1/2 0.08 15 104 90 NA 40 150 0.400 0.4 0.190
-1282
5/8 0.08 15 104 100 NA 50 115 0.400 0.5 0.190
-1282
3/4 0.08 15 104 100 NA 60 100 0.450 0.7 0.190
-1282
7/8 0.08 15 104 100 NA 60 85 0.450 0.8 0.190
-1282
1 0.08 15 104 100 NA 60 70 0.450 0.9 0.195
-1282
1.25 0.08 15 104 100 NA 60 50 0.450 1.0 0.230
-1283
1 1/2 0.08 15 104 100 NA 80 35 0.450 1.7 0.245
-1283
1 3/4 0.08 15 104 100 NA 90 25 0.450 3.000 0.275
-1283
2 0.08 15 104 100 NA 90 18 0.280
-1283
2 1/2 0.08 15 104 100 NA 90 10 NA
-1283
3 0.08 15 104 100 NA 90 7 NA -1283
mm mm bar Ball bar Ball bar
(mm/min)
(mm) (sec) (mm)
12 2.00 1 104 6.2 NA 2.8 3810 10.2 0.4 4.8
-1282
15 2.00 1 104 6.9 NA 3.5 2920 10.2 0.5 4.8
-1282
20 2.00 1 104 6.9 NA 4.1 2540 12.7 0.7 4.8
-1282
25 2.00 1 104 6.9 NA 4.1 1780 12.7 0.9 5.0
-1282
30 2.00 1 104 6.9 NA 4.1 1270 12.7 1.0 5.8
-1283
35 2.00 1 104 6.9 NA 5.5 900 12.7 1.7 6.2
-1283
40 2.00 1 104 6.9 NA 6.2 660 12.7 3.0 6.6
-1283
50 2.00 1 104 6.9 NA 6.2 460 7.1
-1283
60 2.00 1 104 6.9 NA 6.2 325 NA
-1283
70 2.00 1 104 6.9 NA 6.2 285 NA -1283
5.8-13.97
5.8-13.97
7.6-13.97
7.6-13.97
3.6-13.97
3.8-13.97
5.6-13.97
5.8-13.97
.150-.550
.220-.550
.230-.550
.230-.550
.130-.550
.130-.550
.140-.550
.140-.550
Minimum
Clearance
Eff
ec
ti
ve
t
Material
Thi
c
kn
ess
Edge Start
Edge Start
Edge Start
Pierce
Delay
Effective Cut Height
(mm)
3.3-13.97
3.3-13.97
Kerf Width
@ Rec.
Speed
Shield
Gas
Distributor
Plasma (O
2
)
Shield
(Air)
Edge Start
Edge Start
Edge Start
Pre Flow
Pressure
(Air
2
)
Cut Flow Rates /
Pressures Travel
Speed
Initial
Piercing
Height
.230-.550
.230-.550
.230-.550
Kerf Width
@ Rec.
Speed
Shield
Gas
Distributor
Plasma (O
2
)
Shield
(Air)
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Effective Cut Height
(in)
Eff
ec
ti
ve
Material
Thi
c
kn
ess
22-1282
22-1283
22-1057
Cartridge
22-1042 22-1090 22-1022
Pre Flow
Pressure
(Air)
Cut Flow Rates /
Pressures
Minimum Clearance
Mild Steel
300A Bevel Cut
O
2
Plasma / Air Shield
BOLD TYPE
indicates maximum piercing parameters.
BOLD ITALIC
indicates edge starts only.
Requires CCM version 3.4 or later. Requires GCM version 3.2 or later.
Shield
Retainer
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode
22-1021
Electrode
Shield Cap
Shield Retainer
Tip
Shield Gas Distributor
Art # A-08551_AB
Plasma Gas
Distributor
(Straight)
(Swirl)
Cartridge Assembly
This Art Is For Reference ONLY
8.06 Bevel Cutting 250 - 300 Amp