User Manual

Torch Data 8-13 Manual 0-4821 Rev. AG
Stainless Steel
200A
Air Plasma / Air Shield
35-1018
35-1019
35-1281
35-1057
35-1085
35-1020
Shield
Retainer
Shield Cup
Shield
Cap
Shield Gas
Distributor
Tip
Plasma Gas
Distributor
Electrode
Cartridge
Art # A-07596
35-1046
35-1029
(ga) (in) inch (PSI) Ball (PSI) Ball (PSI) Volts
(in)
±0.005
(ipm ) (in) (s ec) (in)
3/16
0.1875
56 90 110 70
170
0.140
300 0.300 0 0 .16 3
1/4 0.250 56 90 110 70 173 0.140 275 0.300 0.1 0.162
3/8 0.375 56 90 110 70 173 0.140 200 0.300 0.2 0.169
1/2 0.500 56 90 110 70 175 0.140 145 0.350 0.3 0.169
5/8 0.625 56 90 110 70 177 0.140 110 0.400 0.4 0.174
3/4 0.750 56 90 110 70 179 0.160 80 0.450 0.5 0.176
7/8 0.875
56
90 110 70 181 0.170 60 0.450 0.6 0.181
11.000
56
90 110 70 184 0.180 45 0.500 1.1 0.181
1 1/4 1.25 0
56 90 110 70 196 0.200 25 0.500 2.0 0.207
1 1/2 1. 500
56 90 110 70 204 0.200 15 0.220
2
2.000 56 90 110 70 20 5 0.200 10 0.230
(Bar) Ball (Bar) Ball (Bar) Volts
(mm)
±0.1
(mm/min) (mm) (sec) (mm)
3.9 90 7.6 4.8 170 3.6 7530 7.6 0 4.1
3.9 90 7.6 4.8 173 3.6 7130 7.6 0.1 4.1
3.9 90 7.6 4.8 173 3.6 6000 7.6 0.2 4.2
3.9 90 7.6 4.8 175 3.6 4870 4.8 0.2 4.3
3.9 90 7.6 4.8 177 3.6 3990 8.6 0.3 4.3
3.9 90 7.6 4.8 179 3.6 3040 9.8 0.4 4.4
3.9 90 7.6 4.8 181 4.4 1880 11.4 0.5 4.5
3.9 90 7.6 4.8 184 4.5 1190 12.5 1 4.6
3.9 90 7.6 4.8 196 5.1 630 12.7 1.9 5.3
3.9 90 7.6 4.8 204 5.1 390 5.6
3.9 90 7.6 4.8 205 5.1 250 5.8
200A Stain l ess Steel (Air/Ai r)
Material
Thicknes s
Pre Flow
Pres s ure
(Air)
Cut Flow Rates / Pres s ures
Arc
Volta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf W idth
@ Min/Max
Plasma (Air) Shield (Air)
See
Note
Edg e Start
Edg e Start
Material
Thicknes s
Pre Flow
Pres s ure
(Air)
Cut Flow Rates / Pres s ures
Arc
Volta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Kerf W idth
@ Rec.
Speed
Plasma (Air) Shield (Air)
(mm)
5
See
Note
6
8
10
12
15
20
25
32
38
Note: Set air shield parameters by pressure only.
Edg e Start
50 Edg e Start
Bold
type in dic ates maximum piercing par a met ers.
Bold italic
indic a tes edge st ar ts only.