User Manual

Torch Data 8-15 Manual 0-4821 Rev. AG
(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
3/8 0.375 20 80 90 5 55 155 0.160 95 0.300 0.0 0.110
1/2 0.500 20 80 90 5 55 156 0.160 85 0.300 0.4 0.115
5/8 0.625 20 80 90 5 55 158 0.180 65 0.300 0.5 0.122
3/4 0.750 20 80 90 5 55 163 0.200 50 0.300 0.7 0.133
7/8 0.875 20 80 90 5 55 177 0.250 40 0.400 0.9 0.149
1 1.000 20 80 90 5 55 183 0.300 35 0.450 1.0 0.148
1 1/ 4 1. 250 20 80 90 5 55 185 0. 300 20 0.176
1 1/ 2 1. 50 0 20 80 90
5
55 200 0.350 10 0.211
1 3/ 4 1. 75 0 20 80 90
5
55 207 0.350 8 0.216
(Bar) (Ball) (Bar) (Ball) (Bar) Volts
(mm)
±0.1
( mm/min)
(mm) (sec) (mm)
1.4 80 6.3 5 3.8 155 4.1 2400 7.6 0.0 2.8
1.4 80 6.3 5 3.8 156 4.1 2000 7.6 0.4 2.9
1.4 80 6.3 5 3.8 157 4.4 1550 7.6 0.5 3.1
1.4 80 6.3 5 3.8 165 5.1 1100 7.6 0.7 3.4
1.4 80 6.3 5 3.8 183 7.6 900 11.4 0.9 3.7
1.4 80 6.3 5 3 .8 18 5 7.6 500 4.5
1.4 80 6.3
5
3.8 200 8.9 250 5.4
1.4 80 6.3
5
3.8 206 8.9 200 5.5
* P r e ssur e o f the water supply line should be r egu lated by cu st omer pr essure r egu lator.
Note1:
Ohmic h eight sensing is not r ecommended with wate r shield. W ater on the plate interferes elec tri c ally with t h e
ohmic sensing c i r c uit.
Note2:
Wa ter sourc e used for shield must be demineralized.
Pierce
Delay
K er f W i dth
@ Rec.
SpeedPlasma (N
2
)
Shield
(H
2
O)*
Arc
Volta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
38
Ma te ri al
Thicknes s
Pre Flow
Pressure
(N
2
)
Cut Flow Rates /
Pressures
10
12
(mm)
Edge Start
20
K er f W i dth
@ Rec.
SpeedPlasma (N
2
)
Cut Flow Rates /
Pressures Arc
Volta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height
Pierce
DelayShield
(H
2
O)*
CartridgeShield Cup Shield Cap
Shield Gas
Distributor
Tip
35-1048 35-1089
Pre Flow
Pressure
(N
2
)
Stainless Steel
200A
N
2
Plasma / H
2
O Shield
Edge Start
35-102035-1016 35-1039 35-1273 35-1064
Plasma Gas
Distributor
Electrode
B OLD TYPE
indicates maxim um piercing param eters.
B OLD ITALIC
indic a tes edge st ar ts only.
Requir e s CCM version 3.4 or l ater. Requir es GCM version 3.2 or later .
Edge Start
Edge Start
25
32
44
Edge Start
Edge Start
15
Ma te ri al
Thicknes s
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB