User Manual

Torch Data 8-21 Manual 0-4821 Rev. AG
Aluminum
200A
H35 Plasma / N
2
Shield **
35-1273
Shield Cup
35-1016
Shield Cap
Shield Gas
Distributor
Tip
35-1058
Art # A-07610
Plasma Gas
Distributor
35-1043
< 1” (25mm)
1” + (25mm)
35-1032
Electrode
35-1087
Cartridge
35-1020
35-1031
>
(ga) (in) inch (PSI) Ball (PSI) Ball (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
1/2 0.500 20 100 100 40 148 0.300 150 0.350 0.2 0.179
5/8 0.625 20 100 100 40 153 0.300 110 0.350 0.3 0.166
3/4 0.750 20 100 100 40 160 0.300 70 0.400 0.4 0.178
7/8 0.875
20
100 100 40 164 0.350 55 0.450 0.5 0.215
1 1.000
20
100 100 100 173 0.350 40 0.500 0.7 0.187
1 1/ 4 1. 250
20 100 100 100 176 0.350 32 0.170
1 1/ 2 1. 500
20 100 100 100 183 0.375 25 0.175
2 2.000
20 100 100 100 186 0.375 15 0.215
(Bar) Ball (Bar) Ball (Bar) Volts
(mm)
±0.1
(mm/mi
n)
(mm) (sec) (mm)
1.8 1 00 6.9 2.8 148 7.6 3810 8.9 0.2 4.5
1.8 1 00 6.9 2.8 152 7.6 3070 8.9 0.3 4.3
1.8 1 00 6.9 2.8 161 8.0 1750 10.5 0.4 4.8
1.8 1 00 6.9 2.8 172 8.9 1060 12.5 0.7 4.8
1.8 1 00 6.9 6.9 176 8.9 500 4.3
1.8 1 00 6.9 6.9 183 9.5 330 4.4
1.8 1 00 6.9 6.9 186 9.5 210 5.4
Not e: S et ai r s hi eld parameters by pres s ure only.
See
Note
See
Note
** Requi res Fi rm ware vers i on 3. 2 or higher for t he Power S upply and 2. 1 or higher for t he Gas Cont rol Box .
50 E dge S tart
* Loc k pi erc e height for firs t 0. 5" t o 1" of c utt i ng t o avoi d t orch hitt i ng t he pierce metal puddle.
S l i ght ly decreas ing the s hi eld gas press ure m i nim i z es dros s on alum i num cut ting
32 E dge S tart
38 E dge S tart
12
15
20
25
K er f Width
@ Rec.
Speed
Plasma
(H35)
Shield (N
2
)
(mm)
E dge S tart
Ma te ri a l
Thicknes s
P r e Flow
Pressure
(N
2
)
Cut Flow Rate s / P r essures
Arc
Vo l ta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height*
Pierce
Delay
Plasma
(H35)
Shield (N
2
)
E dge S tart
E dge S tart
200A Al umi n u m (H35/ N
2
)
Ma te ri a l
Thicknes s
P r e Flow
Pressure
(N
2
)
Cut Flow Rate s / P r essures
Arc
Vo l ta g e
Torch
Working
Height
Travel
Speed
Initial
Piercing
Height*
Pierce
Delay
K er f Width
@
Mi n /Max