User Manual

Torch Data 8-22 Manual 0-4821 Rev. AG
(ga) (in) inch (PSI) (Ball) (PSI) (Ball) (PSI) Volts
(in)
±0.005
(ipm) (in) (sec) (in)
1/2 0.500 20 100 90 5 55 168 0.250 110 0.300 0.3 0.120
5/8 0.625 20 80 100 5 55 170 0.300 105 0.350 0.5 0.126
3/4 0.750 20 80 100 5 55 175 0.300 90 0.350 0.6 0.127
7/8 0.875 20 80 100 5 55 180 0.300 75 0.350 0.8 0.133
1 1.000 20 80 100 5 55 194 0.350 50 0.400 1.0 0.144
1.25 1.250 20 80 100 5 55 208 0.400 25 0.450 2.0 0.180
1 1/2 1. 50 0 20 80 100 5 55 210 0.400 20 0.500 3.0 0.197
1 3/ 4 1. 75 0 20 80 100
5
55 212 0.400 18 0.201
2 2.000 2 0 80 100
5
55 215 0.400 12 0.204
(Bar) (Ball) (Bar) (Ball) (Bar) Volts
(mm)
±0.1
(mm/min)
(mm) (sec) (mm)
1.4 100 6.3 5 3.8 167 6.3 2900 7.6 0.3 3.0
1.4 80 6.9 5 3.8 170 7.5 2700 8.9 0.5 3.2
1.4 80 6.9 5 3.8 176 7.5 2200 8.9 0.6 3.3
1.4 80 6.9 5 3.8 194 8.9 1300 10.2 1.0 3.6
1.4 80 6.9 5 3.8 208 10.2 630 11.4 2.0 4.6
1.4 80 6.9 5 3.8 210 10.2 500 12.7 3.0 5.0
1.4 80 6.9 5 3.8 212 10.2 460 5.1
1.4 80 6.9
5
3.8 215 10.2 300 5.2
* P r e ssur e of t h e wa ter supply line should be r egu lated by custo mer pressure reg ulator.
Note1:
Ohm ic height sens ing is not recommended with water shield. Water on the plate interferes electrically with the
ohmic sensing circuit.
Note2:
Wa ter sourc e used fo r shield must be deminerali zed.
Aluminum
200A
N
2
Plasma / H
2
O Shield
B OLD TYPE
indic ates maximum pier c in g paramet er s.
B OLD ITALIC
indic ates edge st a r ts only.
Requir e s CCM version 3.4 or later. Requir es G CM version 3 .2 or l ater.
Edge Start
Edge Start
32
38
50 Edge Start
Edge Start
25
Kerf W idth
@ Rec.
Speed
Plasma (N
2
)
Travel
Speed
Initial
Piercing
Height
Pierce
Delay
Shield
(H
2
O)*
Cut Flow Rate s /
Pressures Arc
Volta g e
Torch
Working
Height
35-102035-1016 35-1039 35-1273 35-1064
Pierce
Delay
Kerf W idth
@ Rec.
SpeedPlasma (N
2
)
Plasma Gas
Distributor
Electrode CartridgeShield Cup Shield Cap
Shield Gas
Distributor
Tip
35-1048 35-1089
44
Mate ri al
Thicknes s
Pre Flow
Pres sure
(N
2
)
Cut Flow Rate s /
Pres sures
12
15
(mm)
20
Mate ri al
Thicknes s
Pre Flow
Pres sure
(N
2
)
Initial
Piercing
Height
Shield
(H
2
O)*
Arc
Volta g e
Torch
Working
Height
Travel
Speed
Electrode
Shield Cap
Tip
Shield Gas
Distributor
Plasma Gas
Distributor
Cartridge
Shield Cup
This Art Is For Reference ONLY
Art # A-07958_AB