Manual

6
OPERATION, REFRIGERATOR
During ini al startup, or any me power is interrupted, there will
be an approximate 5 minute delay before the refrigerator starts.
During this period the controller will be assessing the tempera-
ture in the refrigerator and the display will appear erra c, this is
normal. The desired temperature set point can be programmed
during this start up period.
Star ng your refrigerator
The refrigerator will begin start up when ini ally plugged in or
when power resumes a er a power outage. At this  me the re-
frigerator will take approximately 5 minutes to begin running as
noted above. If the refrigerator has been turned off during use,
“OFF” will appear on the display. To start the refrigerator from
the “OFF” posi on press and hold the ON/OFF bu on for three
seconds.
Set temperature
To set temperature set point, press and con nue to hold “SET”
bu on. A er one second, set point will be displayed. While
holding “SET” bu on use the “WARMER” or “COLDER” bu on to
desired set point.
NOTE: Momentarily pressing & releasing “SET” bu on will access
informa on menu of control. Refer to appendix A for informa on
on this feature.
Refrigerator opera on
The available temperature range of the refrigerator is 33° to 45°
(1° to 7° C).
It may take up to 24 hours for your refrigerator to reach desired
temperature. This will depend on amount of contents loaded
and number of openings and closings of the door.
For best results allow refrigerator to “pull down” to desired set
point before loading. Once contents are loaded, allow at least 48
hours for temperature to stabilize before making any adjust-
ments to the set point.
Alarms
Your refrigerator control will monitor refrigerator func on and
alert you with a series of audible and visual alarms.
• Door Ajar Alarm: If the door has been le
open for over fi ve (5) minutes, the alarm
will sound in one (1) second intervals. The
display panel will fl ash “do” and the LED light will be a steady
amber color. This will stop as soon as the door is closed.
• High and Low Temperature Alarm: If your
unit reaches an unacceptable temperature
outside of your set point, the alarm will
sound in one (1) second intervals. The
display panel will fl ash either “hi” or “Lo”
depending upon the condi on and the LED light will be a steady
amber color. “hi” indicates that the temperature is 10° F (5.5°C)
above the set point and “Lo” indicates that the temperature is
10° F (5.5°C) below the set point. The alarm will remain ac ve
un l the condi on is corrected.
NOTE: During ini al appliance start-up, the high temperature
alarm may sound un l the interior temperature reaches set
point.
• Temperature Sensor Fault: If the controller
detects that the temperature sensor is
not properly func oning, a temperature
sensor alarm will sound. “E1” will fl ash on the display, and an
alarm will sound. Please call AGA MARVEL Customer Service or
your dealer if this error code is displayed.
• Condenser Needs Cleaning:
When the refrigerator has reached the
recommended amount of run  me to neces-
sitate cleaning the air fl ow, “cL” will fl ash on the display as a
reminder. See the “Care and Cleaning” sec on for cleaning
instruc ons.
To clear the alarm:
1) Press and release the “SET bu on four  mes.
“cnd” will be displayed on the screen.
2) While “cnd” is displayed, press and hold the “SET” but-
ton. The display will show the number of weeks the
refrigerator has been running.
3) While holding the “SET” bu on, press and release the
ON/OFF bu on. The number shown on the display will
reset to 0.
4) Release the “SET” key.
NOTE
Control
Figure 4
Door Switch
Alarm Mute
Press any key to mute the audible por on of an alarm,.
NOTE-This ac on will only mute the alarm. If the condi on that
caused the alarm con nues, the alarm code will con nue to fl ash
and will sound for 20 seconds every 60 minutes.
Turning Refrigerator Off
To turn refrigerator off , press and hold “ON/OFF” bu on for
three (3) seconds. “OFF” will appear on the display.