TWIN EAGLES POWER BURNER INSTALLATION, USE & CARE MANUAL Models: TEPB24HG-B (As Shown) TEPB24-B P/N: 18652B (05/14)
IMPORTANT SAFETY INFORMATION – TWIN EAGLES GAS POWER BURNER WARNING! Read this manual carefully and completely before using your Power Burner to ensure proper operation, proper installation, proper servicing and to reduce the risk of fire, burn hazard and/ or other injury. FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid. 4. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.
GENERAL SAFETY REQUIREMENTS: 1. The installation of this appliance must conform with local codes or, in the absence of local codes, either the National Fuel Gas Code, ANZI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code. 2. This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles and /or boats. 3.
TABLE OF CONTENTS – TWIN EAGLES GAS POWER BURNER GETTING STARTED…………………………………………………………………………………….. 1 GAS REQUIREMENTS o GAS SAFETY REQUIREMENT…………………………………………..……………... 2 o LP GAS HOOKUP………….………………………………………………………..…… 3 o NATURAL GAS INSTALLATION…………………………………………………..….. 4 o LEAK TEST…………………………………………………………………………….… 4 ELECTRICAL REQUIREMENTS ……..…………………………..………………………………..… 5 ELECTRICAL WIRING DIAGRAM AND CUTOUT DIMENSIONS…………..…………………..
3. Fill up the Warranty Registration Card and mail it to the indicated address. Specifications Counter Opening Height Counter Opening Width Counter Opening Depth Btu NG Orifice Outer Ring NG Orifice Inner Ring LP Orifice Outer Ring LP Orifice Inner Ring Value 11.50” 22.00” 20.50” 70,000 #30 #41 #49 #53 GAS SAFETY REQUIREMENTS – TWIN EAGLES GAS POWER BURNER Each appliance is set and tested at the factory for the type of gas supply to be used.
It must be provided with a shut-off valve terminating in gas tank valve outlet. It must include a collar to protect the cylinder valve. The cylinder supply system must be arranged for vapor withdrawal. Do not operate the gas Power Burner indoors or in any enclosed area. If the gas Power Burner is not in use, the gas must be turned off at the supply cylinder. If the Power Burner is to be stored indoors, disconnect the gas supply cylinder and leave the cylinder outdoors.
NATURAL GAS INSTALLATION – TWIN EAGLES GAS POWER BURNER The installation must conform with local codes or, in the absence of local codes, with either the national Fuel Gas Code, ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas Installation Code or CAN/CGA-B149.2, Propane Installation Code. 1. This gas appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at the test pressures in excess of 1/2 psi (3.5 kPa). 2.
LEAK TEST 1) Prepare a leak testing solution of sudsy water by mixing in a spray bottle with half liquid soap and half water. 2) Confirm that all control knobs are in the OFF position. 3) Turn the main gas valve supply ON. 4) Apply leak testing solution by spraying on the pipe joints, fittings, and hose.
ELECTRICAL WIRING DIAGRAM AND TYPICAL CUTOUT DIMENSION CONNECTION DIAGRAM LADDER DIAGRAM Note: It is recommended to build the enclosure for the power burner 6”-12” lower than the countertop. LOCATING THE POWER BURNER – TWIN EAGLES GAS POWER BURNER This gas appliance is designed and certified for outdoor use only. Do not locate this Power Burner under overhead combustible surfaces. Do not operate the Power Burner inside a building, garage, recreation vehicle or any enclosed area.
CLEARANCE TO COMBUSTIBLE CONSTRUCTION A minimum clearance of 12” from the sides and 6” from the back of the Power Burner to adjacent vertical combustible construction must be maintained. DÉGAGEMENT DE TOUTE CONSTRUCTION COMBUSTIBLE Il faut maintenir une distance minimum de 12 po (30.48 cm) sur les côtés et de 6 po (15.24 cm) sur l’arrière du gril par rapport aux constructions combustibles verticales adjacentes.
CLEANING & MAINTENANCE – TWIN EAGLES GAS POWER BURNER STAINLESS STEEL The TWIN EAGLES Power Burner is made of stainless steel construction. It is non-rusting and nonmagnetic. Never clean the stainless steel when it is hot. After the initial cooking use, certain areas of the Power Burner may discolor. This is a normal discoloration caused by the intense heat given off by the burner. Specks of grease can gather on the surface of the stainless steel and get baked-on.
OPERATING INSTRUCTIONS – TWIN EAGLES GAS POWER BURNER BEFORE LIGHTING THE POWER BURNER DO NOT ATTEMPT TO LIGHT THE POWER BURNER IF YOU SMELL GAS. WARNING! IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED WITH THEIR ORIFICES INSIDE THE BURNERS AIR SHUTTERS. If not properly installed, gas may leak outside of the burner that could lead to fire, potential damage to your Power Burner and bodily injury. Inspect the gas supply piping or hose prior to turning the gas ON.
S22321 Power Burner Cover 1 1 2 S22330Y Power Burner HD Grate 1 1 3 S16230 Hot Surface Igniter 1 1 1 4 S22309 Top Trim 1 1 5 S13362Y Brass Burner 1 6 S22328 Transformer Cover 7 S16111 8 TEPB 24-BN 1 TEPB 24-BL Description TEPB 24HG-BN TE Part Number TEPB24HG-BL Item No. TEPB 24-BN TEPB 24-BL TEPB 24HG-BN TEPB24HG-BL REPLACEMENT PARTS – TWIN EAGLES GAS POWER BURNER Item No.
TROUBLESHOOTING GUIDE – TWIN EAGLES GAS POWER BURNER BEFORE CALLING FOR SERVICE: If your Twin Eagles Power Burner does not function properly, use the following troubleshooting guide before contacting your dealer for service. The troubleshooting guide may save the cost of a service call and the inconvenience of being without your Power Burner. PROBLEM Power Burner will not light. WHAT TO DO 1. Push in the knob and verify that the igniter glow. 2. If the igniter does not glow, verify proper power supply.
TWIN EAGLES POWER BURNER WARRANTY LIMITED LIFETIME WARRANTY: Twin Eagles warrants the main burners, grates and all fabricated stainless steel components, to be free from defects in materials and workmanship under normal residential use for the lifetime of the product. This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust and oxidation which are normal conditions and to be expected with any outdoor product.
HOW TO OBTAIN SERVICE For service, please contact your TWIN EAGLES dealer or call TWIN EAGLES direct at (800) 7892206 or (562) 802-3488 or fax (562) 802-3391 Mailing address: Twin Eagles, Inc. 13231 East 166th Street Cerritos, CA 90703 Visit us at www.twineaglesbbq.
FOR YOUR RECORDS Please record the following information and refer to them when contacting the company or an authorized service agent. This information is found on the data nameplate, located on the panel behind the control panel of the Power Burner. Remove the drip pan to visually access the nameplate from the front of the Power Burner. A second label with model number and serial number is located under the right side of the control panel.
