User Manual

ManualsBrandsTwo Brothers Racing ManualsSensorsCan-Am Spyder Renegade 800

ITBR001-256 www.twobros.com 2006-09 Outlander 800/2007-10 Renegade 800 - 1

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION

2006-09 Outlander 800/2007-10 Renegade 800

Installation Instructions

401 S. Grand Ave. Santa Ana, CA 92705

(800) 211-2767 www.twobros.com

DOWNLOAD THE TOPTUNE SOFTWARE

AND LATEST MAPS FROM OUR

WEBSITE:

www.twobros.com

THE IGNITION MUST BE TURNED

OFF BEFORE INSTALLATION!

PARTS LIST

1 Juice Box Pro™

1 USB Cable

1 Top Tune CD-ROM

1 Installation Guide

2 Velcro strip

1 Alcohol swab

1 Posi tap

Summary of content (5 pages)

PAGE 1
PARTS LIST 2006-09 Outlander 800/2007-10 Renegade 800 I n s t a l l a t i o n I n s t ru c t i o n s 1 1 1 1 2 1 1 Juice Box Pro™ USB Cable Top Tune CD-ROM Installation Guide Velcro strip Alcohol swab Posi tap THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION! DOWNLOAD THE TOPTUNE SOFTWARE AND LATEST MAPS FROM OUR WEBSITE: www.twobros.com PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION 401 S. Grand Ave. Santa Ana, CA 92705 (800) 211-2767 www.twobros.com ITBR001-256 www.twobros.
PAGE 2
S electing the M ap Pos ition T he J uice B ox Pro com es loaded with up to ten m aps . U s ing a #1 Phillips s crewdriver, turn the m ap s elect dial to toggle between the loaded m aps . R efer to the m ap pos ition table below for the m aps included in your J uice B ox Pro. U s ing the R PM R ange Dials T he Low, M id, and High R PM Dials refer to the R PM range, in thirds , of your vehicle. E ach dial allows +/- 10% fuel adjus tm ent on top of what fuel changes are done in the m ap.
PAGE 3
1. Remove the seat. Figure A 2. Remove the right hand side covers as shown in Figure A. remove 3. Using the supplied velcro, secure the Juice Box Pro to the underside of the airbox cover as shown in Figure B. air box cover Make sure to clean both surfaces with the alcohol swab before attaching. Figure B Note: Figure B shows the Juice Box Pro in the general location of the install. Place the unit above this location. 4. Route the Juice Box Pro wiring harness to the right side of the ATV.
PAGE 4
Figure D stock connector 6. Attach the yellow colored wires from the Juice Box Pro to the stock wiring harness and the rear fuel injector as shown in Figure D. Juice Box Pro connectors 7. Unplug the stock wiring harness from the front injector as shown in Figure E. Figure E unplug stock harness 9. Attach the orange colored wires from the Juice Box Pro to the stock wiring harness and front fuel injector as shown in Figure F. Figure F stock connector 8.
PAGE 5
10. Locate the Throttle Position Sensor (TPS) connector. The TPS connector is located on the rear of the throttle body as shown in Figure G. Figure G 11. Unplug the TPS connector. unplug grey wire from Juice Box Pro 12. Attach the supplied posi-tap to the white/brown wire of the TPS harness. 13. Attach the grey wire from the Juice Box Pro to the posi-tap. Figure H Note: It is recommended to use dielectric grease on these connections. 14. Plug the wiring harness back onto the TPS. 15.