Emissions Legal Owner manual

Two Brothers Racing
Juice Box™ - Fuel Controller
2006-07 Honda CBR1000RR Installation & Operation Manual
Part # 008-181C
Parts Incuded
Installation Instructions
Qty. Description Part Number
1 Juice Box™ Fuel Control Kit 008-181C
3 Zip Ties
1 Adhesive Velcro Square
V.A.L.E .
V A R I A B L E A X I S L O C K I N G E X H A U S T
TM
Remove fuel tank support bolts (both sides) (Fig 6) and
raise or remove fuel tank.
Place JUICE BOX™ in tail section and route the JUICE
BOX™ harness towards injectors.
You will be plugging the JUICE BOX™ harness into the
lower injectors not the uppers. Disconnect stock injector
(one at a time) connect JUICE BOX™ connector to bikes
injector then connect stock injector connector to JUICE
BOX™’s black connector. (Fig 7)
Connect ground lead to either the negative post of the
battery or suitable frame ground.
Assembly is the opposite of disassembly.
Start the bike. The green LED should scroll left to right and
back for about 3-5 seconds and then go to 1-2 steady or
slowly flashing green LED’s. If the number 1 green LED
and number 8 red LED’s continue flashing after startup
or idling, an injector wiring error is indicated. Re-check
the wires from the JUICE BOX™ and make sure they are
connected to the proper wire of your bike’s stock harness.
MAKE SURE you have the correct wires selected in
the stock harness. DO NOT PROCEED UNLESS ABOVE
CONDITIONS ARE MET.
NOTE: Re check your wire routing and JUICE BOX™
location and make certain that in no way the wires can
come into contact with any moving parts or high heat
source and that the JUICE BOX™ is mounted in a way as
to not cause a handling problem with the machine.
5.
6.
7.
8.
9.
10.
11.
IMPORTANT - PLEASE READ CAREFULLY
Warranty
Two Brothers Racing warrants that this product carries a warranty for 2 years from date of purchase against original
defects in materials and workmanship. Should this product fail to perform for either of the above reasons, Two Brothers
Racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser.
To obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of
original purchase.
We recommend that this performance part be installed by a qualied motorcycle
technician. If you have any doubts as to your ability to install this performance part,
please consult with your local motorcycle dealer. Read all instructions rst before
starting installation. Make sure the vehicle and exhaust system are completely cool
before starting the installation. Also, make sure the vehicle is secure during installation.
Be sure to save all stock components for possible use later.
This Juice Box is legal for use on Emissions Controlled street and highway vehicles.
The Juice Box™ is not applicable, nor inteded for use on aircraft.
Thank you for purchasing a genuine Two Brothers Racing
JUICE BOX™. This product represents a radical step
forward in tuning fuel-injected motorcycles and ATVs for
optimal performance using “load-based” technology.
We at Two Brothers Racing hope that you will find this
development as exciting and useful as we do. And
remember: Proper Fuel = Maximum Power!
Make sure the vehicle is completely cool before starting
the installation. Also, make sure the vehicle is secure and
will not roll around.
Remove rider and passenger seat.
Remove the 3 Allen bolts from the large side panel (Fig
1) and the 2 plastic screw type fasteners (Fig 2) and the 2
plastic pull style fasteners, all located on the inside of the
main fairing and remove fairing. Repeat on opposite side.
Remove the 12mm bolt and the 2 plastic fasteners from
the rear tank cover (Fig 3). Also remove the 5mm Allen
bolt from the side panel,(both sides) (Fig 3) and plastic
pull style fasteners (Fig 5) and remove tank cover.
1.
2.
3.
4.
Tools Needed For Install
- Phillips Screwdriver
- 12mm Wrench or Socket
- 5mm Allen Wrench
Continued on page 2
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
Fig 6
Fig 7