TYAN GT24 B7016 Service Engineer’s Manual 1 http://www.tyan.
http://www.tyan.
PREFACE Copyright This publication, including all photographs, illustrations, and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any material contained herein, may be reproduced without written consent of manufacturer. Copyright 2009 MiTAC International Corporation. All rights reserved. ® TYAN is a registered trademark of MiTAC International Corporation. Version 1.
Federal Communication Commission (FCC) Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC Part 15: This device complies with part 15 of the FCC Rules Operation is subject to the following conditions: 1) This device may not cause harmful interference; 2) This device must accept any interference received including interference that may cause undesired operation.
About this Manual This manual provides you with instructions on installing your TYAN GT24-B7016. This Manual is intended for experienced users and integrators with hardware knowledge of personal computers. This manual consists of the following parts: Chapter1: Provides an introduction to the TYAN GT24-B7016 barebones, standard parts list, describes the external components, gives a table of key components, and provides block diagram of the system.
SAFETY INFORMATION Before installing and using TYAN GT24-B7016, take note of the following precautions: ·Read all instructions carefully. ·Do not place the unit on an unstable surface, cart, or stand. ·Do not block the slots and opening on the unit, which are provided for ventilation. ·Only use the power source indicated on the marking label. If you are not sure, contact the power company.
Table of Contents Chapter 1: Overview ......................................................................... 9 1.1 About the TYAN GT24-B7016 .................................................. 9 1.2 Product Models....................................................................... 10 1.3 Features.................................................................................. 11 1.4 Standard Parts List ................................................................. 15 1.4 Standard Parts List .......
2.2 Rack Mounting........................................................................ 40 2.2.1 Installing the Server in a Rack......................................... 40 2.2.2 Installing the inner Rails to the Chassis........................... 41 2.2.3 Installing the Outer Rails to the Rack .............................. 42 2.2.4 Rack mounting the Server ............................................... 44 Chapter 3: Replacing Pre-Installed Components ........................ 47 3.
Chapter 1: Overview 1.1 About the TYAN GT24-B7016 ® Congratulations on your purchase of the TYAN GT24-B7016, a highly optimized rack-mountable barebone system. GT24-B7016 is designed to ® support up to two Intel “Nehalem-EP processors and up to 144GB DDR3-800/1066/1333 memory, providing a rich feature set and incredible ® performance.
1.2 Product Models Model B7016G24W4H B7016G24V4H HDD Bays Hot-swap, 4HDDs Hot-swap, 4HDDs 10 http://www.tyan.
1.3 Features TYAN GT24-B7016 (B7016G24W4H/B7016G24V4H) System Front Panel Form Factor 1U Rackmount Chassis Name GT24 Dimension (D x W x H) 25.4" x 17.2" x 1.72" (645 x 436 x 43.6mm) Motherboard S7016WGM3NR/S7016GM3NR Gross Weight 16 kg Buttons (1) RST / (1) NMI / (1) ID / (1) PWR w/ LED LEDs (1) ID / (1) Warning / (3) LAN / (1) BMC I/O Ports (2) USB ports Type / Q'ty 3.5" Hot-Swap / (4) External Drive Bay Supported HDD SAS 3.0Gb/s / SATA-II 3.
Chipset Memory IOH / ICH Intel 5520 / ICH10R Supported DIMM Qty (18) DIMM sockets DIMM Type / Speed DDR3 800/1066/1333 RDIMM/UDIMM Capacity Up to 144GB at launch w/ dual rank RDIMMs Memory channel 6 Channels (3 Channels per CPU) Memory voltage 1.5V PCI-E (1) PCI-E Gen.2 x8 slot / (1) PCI-E Gen.
Temperature Monitors temperature for CPU & system environment LED Fan fail LED indicator / Over temperature warning indicator Others Chassis intrusion detection / Watchdog timer support Onboard Chipset Onboard ServerEngines Pilot2 IPMI 2.
Heatsink / Cooler (2) CHSK-0380, LGA1366 CPU heatsinks for S7016 Rail kit (1) CRAL-0031, sliding rail kit for KGT24 Mounting Ear (1) CEAR-0050, mounting ear kit for GT20/ GT24 Others (1) HDD screw pack (1) CCBL-0310, US type power cord / (1) CCBL-0300, EU Power Cord type power cord 14 http://www.tyan.
1.4 Standard Parts List This section describes GT24-B7016 package contents and accessories. Open the box carefully and ensure that all components are present and undamaged. The product should arrive packaged as illustrated below. 1.4.
1.4.2 Accessories If any items are missing or appear damaged, contact your retailer or browse to TYAN®’s website for service: http://www.tyan.com ® The web site also provides information of other TYAN products, as well as FAQs, compatibility lists, BIOS settings, etc. ® 1 x TYAN Motherboard Drive CD 2 x Heatsinks HDD Screws Power Cables Left to right: Europe, US Mounting Ears & Screws Barebone Manual & Mainboard Manual 16 http://www.tyan.
Rail Kit Rail with Bracket x 2 1.5 Screw Pack Optional Parts Item Chassis Front-Bezel Model Number CFBZ-0070 Picture Quantity Description 1 Front Bezel for GT series 1U chassis 17 http://www.tyan.
1.6 About the Product The following views show you the product. 1.6.1 System Front View Control board Slim SATA DVD-ROM drive Hot-swap HDD Bays USB ports ID button Reset button NMI button 1.6.2 System Rear View LAN3 Power supply (IPMI shared NIC) Serial port & VGA port KB/MS USB ports LAN1 LAN2 18 http://www.tyan.
1.6.
LAN3 LED RJ-45 Linkage/ Activity(left) RJ-45 Linkage/ Activity(Right) State On Blinking Off On On Off Color Green Green Off Amber Green Off Description 10Mb/100Mb/1000Mb linked 10Mb/100Mb/1000Mb activity No LAN linked 1000Mb linked/activity 100Mb linked/activity 10Mb mode or No LAN linked State On Off Color Blue Off Description System identified System not identified ID LED LED ID LED 20 http://www.tyan.
1.6.4 Motherboard (S7016) Layout The diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. 21 http://www.tyan.
1.6.
1.6.6 System Block Diagram 23 http://www.tyan.
1.6.7 Internal View 5 4 3 2 1 1 2 3 4 5 HDD Cage M1232 HDD Board System Fan Unit Power Supply PCI-E Riser Card Assembly 24 http://www.tyan.
Chapter 2: Setting Up 2.0.1 Before you Begin This chapter explains how to install the CPUs, CPU heatsinks, memory modules, and hard drives. Instructions on inserting add on cards are also given. 2.0.2 Work Area Make sure you have a stable, clean working environment. Dust and dirt can get into components and cause malfunctions. Use containers to keep small components separated. Putting all small components in separate containers prevents them from becoming lost.
2.0.4 Precautions Components and electronic circuit boards can be damaged by discharges of static electricity. Working on a system that is connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to GT24-B7016 or injury to yourself. z Ground yourself properly before removing the top cover of the system. Unplug the power from the power supply and then touch a safely grounded object to release static charge (i.e. power supply case).
2.1 Installing Motherboard Components This section describes how to install components on to the motherboa-rd, including CPUs, memory modules and add on cards. 2.1.1 Removing the Chassis Cover Follow these instructions to remove GT24-B7016 chassis cover. 1. Unscrew the rear top cover on the back side as shown in the small diagram. 2. Slide the rear top cover out. 27 http://www.tyan.
2.1.2 Installing the CPU and Heatsink Follow the steps below on installing CPUs and CPU heatsinks. 1. Locate the CPU socket. 2. Press the lever and unlock the CPU socket. 28 http://www.tyan.
A 3. Lift the CPU protection cap up and lay the CPU into the socket(A), ensuring pin1 is correctly located(B); B 4. Close the socket cover and press the CPU lever down to secure the CPU; 29 http://www.tyan.
5. Place the heatsink on top of the CPU and secure it with 8 screws. Note: The system supports two CPUs. For CPU sequence please refer to Chapter 1.6.4. 30 http://www.tyan.
2.1.3 Installing the Memory Follow these instructions to install the memory modules onto the motherboard. 1. Locate the memory slots on the motherboard. 2. Press the memory slot locking levers in the direction of the arrows as shown in the following illustration. 3. Align the memory module with the slot. When inserted properly, the memory slot locking levers lock automatically onto the indentations at the ends of the module. 31 http://www.tyan.
Note: 1). For the DIMM number please refer to the motherboard placement in “2.3 - Board Parts, Jumpers and Connectors” for memory installation. 2). Refer to the memory population option table for recommended memory installation instruction. Memory Population Option Table The following pictures show common types of DDR3 memory modules. 32 http://www.tyan.
CPU0 CPU1 Channel D DIMM D0, D1 & D2 Channel A DIMM A0, A1 & A2 Channel E DIMM E0, E1 & E2 Channel B DIMM B0, B1 & B2 Channel F DIMM F0, F1 & F2 Channel C DIMM C0, C1 & C2 33 http://www.tyan.
The following table outlines the suggested rules for populating memory. For 3 slots per channel RDIMM DIMM2 DIMM1 Single Rank x x x x x x Dual Rank x x x x x x Quad Rank UDIMM x DIMM2 x x DIMM1 DIMM0 Single Rank x x Dual Rank DIMM with heat spreader DIMM0 x x DIMM2 x x DIMM1 DIMM0 x x x x x x 34 http://www.tyan.
Note: 1). “X” indicates a populated DIMM slot. 2). If installing only one processor, you can choose either CPU0 or CPU1. 3). For two slots per channel configuration, it requires population to start with the DIMM slots furthest away from the processor. 35 http://www.tyan.
2.1.4 Installing Hard Drives The GT24-B7016 supports four 3.5” hard drives. Follow these instructions to install a hard drive. 4. 1. Press the locking lever latch and pull the locking lever open. 2. Slide the HDD tray out. 3. Remove the 6 screws. Place a hard drive into the drive tray. 36 http://www.tyan.
5. Use 6 HDD screws to secure the HDD. 6. Reinsert the HDD tray into the chassis and press the locking lever to secure the tray. 37 http://www.tyan.
2.1.5 Installing the PCI-E Cards The GT24-B7016 supports two PCI-E expansion slots. Follow these instructions to install PCI-E cards. 1. Pull open the tab of PCI-E slot on the rear panel in the direction as shown to release the PCI bracket. 2. Take off the PCI bracket. 3. Insert the PCI-E card in the direction of arrow as shown. Close the tab of PCI-E slot to secure PCI-E card. 4. Repeat the same procedures to insert the second PCI-E card into the expansion slot. 38 http://www.tyan.
1 2 3 4 5. The installation of two PCI-E expansion cards are now complete. 39 http://www.tyan.
2.2 Rack Mounting After installing the necessary components, the TYAN GT24-B7016 can be mounted in a rack using the supplied rack mounting kit. Rack mounting kit Sliding Rails x 2 Sliding Brackets x 4 (Front x 2, Rear x 2) Mounting Ears (including screws) x 2 Screws Kit x 1 Mounting Brackets x 4 2.2.1 Installing the Server in a Rack Follow these instructions to mount the TYAN GT24-B7016 into an industry standard 19" rack.
2.2.2 Installing the inner Rails to the Chassis 1. Screw the mounting ear to each side of TYAN GT24-B7016 as shown using 2 screws from the supplied screws kit. 2. Draw out the inner rails from rail assembly. Install inner rails to left and right sides of chassis using 1 M4-4L(A) screw for each side. 41 http://www.tyan.
2.2.3 Installing the Outer Rails to the Rack 1. Measure the distance between inner side of the front and rear mounting brackets in the rack. 2. Locate the front and rear brackets. Rear Bra cket x 2 Front Brack et x2 3. Secure the front bracket to outer rail with 2 M4-4L(A) screws. 4. Reserve the distance same as in Step 2 on rear bracket. Secure the rear bracket to outer rail with 2 M4-4L(A) screws. 5. Secure the outer rail to the rack using 2 brackets and 4 M5-8L(B) screws for each side.
Mounting Bra cket 43 http://www.tyan.
2.2.4 Rack mounting the Server 3. Draw out the middle rail to the latch position. 4. Lift the chassis and then insert the inner slide rails into the middle rails. 5. Push the chassis in and press the latch key (A). Then push the whole system into the rack (B) A 6. B Secure the mounting ears of chassis to the rack with 2 M5-15L(C) screws. 44 http://www.tyan.
Note: To avoid injury, it is strongly recommended that two people lift the TYAN GT24-B7016 into the place while a third person screws it to the rack. 45 http://www.tyan.
NOTE 46 http://www.tyan.
Chapter 3: Replacing Pre-Installed Components 3.1 Introduction This chapter explains how to replace the pre-installed components, including the Motherboard, M1008 LED control board, M1232 HDD board, M2083-RS/M2081-2 PCI-E Riser card, System fan, ODD drive, Power supply unit etc. 3.2 Disassembly Flowchart The following flowchart outlines the disassembly procedure.
Front Components Chassis rear cover DVD ROM PCBs M1008 LED Control Board M1232 HDD Board 48 http://www.tyan.
3.3 Removing the Cover Before replacing any parts you must remove the chassis cover. Follow Chapter 2.1.1 to remove the cover of the GT24-B7016. 3.4 Replacing Motherboard Components Follow these instructions to replace motherboard components, including the motherboard. 3.4.1 Replacing Expansion Card The GT24-B7016 has one preinstalled PCI-E×16 riser card, Follow the instructions below to disassemble the M2083-RS PCI-E riser card. 1.
3. Unscrew the cards from the bracket. a. remove Card M2083 b. remove Card M2081-2 4. Install a new riser card onto the bracket following the procedures mentioned earlier in reverse order. 50 http://www.tyan.
3.4.2 Disconnecting All Motherboard Cables Before replacing the motherboard or certain components, remove cables connected to the motherboard. Follow these instructions to remove all motherboard cables. 1. Disconnect all the power cable. 2. Disconnect SATA DVD cable, Mini SAS cable, USB cable and front panel cable. 3. Disconnect fan cables. 51 http://www.tyan.
3.4.3 Removing the Motherboard After removing all of the aforementioned cables, follow the instructions below to remove the motherboard from the chassis. 1. Remove the heatsinks and processors if installed. 2. Remove the nine screws securing the motherboard to the chassis. 3. Carefully lift the motherboard from the chassis. 52 http://www.tyan.
3.5 Replacing the Slim DVD-ROM Follow these instructions to replace the M1008 LED control board. 1. Remove the power and data cables from the slim DVD-ROM adapter. 2. Press the tab in the directions as shown to release the DVD-ROM drive. 3. The DVD-ROM drive will be freed from the drive bay after pressing the tab. 4. Disconnect the power and data cables from the DVD-ROM drive. 53 http://www.tyan.
5. Remove two screws that secure DVD-ROM drive to the bracket. 6. 7. Replace the DVD-ROM drive. Secure DVD-ROM to the bracket using two screws. Then replace the unit into the drive bay and connect the DVD-ROM power and data cables. 54 http://www.tyan.
3.6 Replacing the LED Control Board Follow these instructions to replace the M1008 LED control board. 1. Remove the two screws securing the LED control board unit to the chassis. 2. Push the LED control board unit out and unplug the cables from the connectors at the back of the unit. 3. Remove three screws securing the LED control board to the bracket. 55 http://www.tyan.
4. Lift the LED control board free from the chassis. After replacing the LED control board, insert the unit into the chassis following the above procedures in reverse. 56 http://www.tyan.
3.6.1 M1008 LED Control Board Features J1 3.6.2 J3 M1008 LED Control Board Connector Pin Definition J1: USB Header Definition VCC USB1USB1+ GND Key Pin 1 3 5 7 9 Pin 2 4 6 8 10 Definition VCC USB2USB2+ GND GND Pin 1 3 5 7 9 11 13 15 17 19 21 23 Pin 2 4 6 8 10 12 14 16 18 20 22 24 Definition J3: SSI Definition PW_LED+ KEY PW_LEDHD/LAN3 LED+ HD/LAN3 LEDPWR_SW+ PWR_SWRESET+ RESETID_SW+ TEMP_SENSER EXT_INT 57 http://www.tyan.
3.7 Replacing the System Fan Follow these instructions to replace the cooling fans in your system. 1. 2. Locate the cooling fans in your system. Unplug the cables connected to the mainboard and lift the fan unit up from the chassis. 3. Follow Step A and B to unlock the fans. After replacing the new fans, reinstall the fans into the chassis following Step A and B in reverse order. 58 http://www.tyan.
A B C 1. Push the fan unit away from the case. 2. After replacing the new fan unit, push the new fan back into the case. D 59 http://www.tyan.
E 4. Connect the fan cables. 60 http://www.tyan.
3.8 Replacing the M1232 HDD Board Step 1: Disconnect all cables connected to M1232 HDD Board. Power cable: SATA Power cable and Mini SAS cable: Step 2: Remove the three screws securing the bracket to the chassis base. 61 http://www.tyan.
Step 3: Lift the bracket up from the chassis. Step 4: Unscrew M1232 board from the bracket. Step 5: Replace a new M1232 HDD Board and reinstall it into the chassis following the above steps in reverse. 62 http://www.tyan.
3.8.1 M1232 HDD Board Features Front View J5 PW2 PW1 J40 J18 J15 J39: Mini SAS Connector J41 J7 63 http://www.tyan.
Rear View: J10 LED1 LED2 J11 LED3 LED4 J13 LED5 LED6 J14 LED7 LED8 64 http://www.tyan.
3.8.2 M1232 HDD Board Connector Pin Definitions PW1 Pin Definition 1 +12V 2 GND 3 GND 4 +5V PW2 Definition GND +12V Pin 1 3 Pin 2 4 Definition GND +12V Pin 1 3 5 7 9 Pin 2 4 6 8 10 Definition GND 3.
J40 PWM select for system FAN3 Pin Definition 1 CPU_PWM 2 PWM_12(FAN3) 3 CPU_PWM2 Pin 1-2 chose by CPU_PWM (Default) Pin 2-3 chose by CPU_PWM2 LED Definition: LED Color State Description HDD fail LED Amber On SATA/SAS HDD fail Off No failure found (LED 2/4/6/8) Power/Access LED SATA/SAS HDD On HDD ready Green Blinking (LED 1/3/5/7) SATA/SAS HDD access activity Off 66 http://www.tyan.
3.9 Replacing the Power Supply 1. Disconnect the power cables from the motherboard and the HDD/FAN board. 2. Remove the screws that secure the power supply to the chassis. 67 http://www.tyan.
3. Take out the power unit and install a new one follow the above steps in reverse. 68 http://www.tyan.
Appendix I: Cable Connection Tables System Fan to S7016 MB System Fan Connect to S7016 MB Fan1 → → → → → J54 Fan2 Fan3 Fan4 Fan5 J53 J52 J51 J49 M1232 HDD Board to S7016 MB Cable M1232 Connect to S7016 MB Mini-SAS Cable J39 → J13 M1008 LED Control Board to S7016 MB Cable M1008 Connect to S7016 MB Control Cable J3 J4 USB Cable J1 → → J11 Power Supply Cables PSU to S7016 MB PSU Connect to S7016 MB 2X12 PWR → → → PW1 P2 P8 69 http://www.tyan.
PSU to M1232 PSU Connect to M1232 P3 → PW2 P4 → PW1 DVD-ROM to S7016 MB & M1232 Cable Connect to S7016 & M1232 SATA Cable → S7016 MB J26 Slim DVD SATA PWR Cable → M1232 J18 70 http://www.tyan.
Appendix II: FRU Parts Table GT24-B7016 FRU Parts Item Model Number Part Number Picture Motherboard S7016WGM3NR / 1 TYAN S7016WGM3NR Motherboard Chassis Unit CCHA-0370 43278090001 1 Chassis Unit;GT24 B7016 Chassis Top Cover CCCV-0180 34078090001 1 GT24 Top Cover Chassis Front Bezel CFBZ-0070 541273910008 1 Front Bezel for GT24 Series 1U Chassis HDD Tray CHDT-0051 340746300001 4 3.
Item Model Number Part Number Picture Quantity Description M1232 / 1 FAN/HDD adapter board M1008 / 1 Front Control Board M2081-2 / 1 Riser Card M2083-RS / 1 PCI-E X16 1U Riser Card CRAL-0031 452783400001 1 Slide Rail Kit CEAR-0050 340740900010 1 Mounting Ear Kit CCBL-072R 422780900001 1 Control Cable, 800mm CCBL-035E 422771000009 1 USB Cable, 500mm CCBL-067O 422784300005 1 Mini SAS Cable, 400mm CCBL-032M 422784300007 1 SATA Cable, 400mm CCBL-0422 422772300003
Appendix III: Technical Support If a problem arises with your system, you should first turn to your dealer for direct support. Your system has most likely been configured or designed by them and they should have the best idea of what hardware and software your system contains. Hence, they should be of the most assistance for you.
Returning Merchandise for Service During the warranty period, contact your distributor or system vendor FIRST for any product problems. This warranty only covers normal customer use and does not cover damages incurred during shipping or failure due to the alteration, misuse, abuse, or improper maintenance of products. Note: A receipt or copy of your invoice marked with the date of purchase is required before any warranty service can be rendered.
